Determination of the Cyclic Properties of Silty Sands

2018 ◽  
pp. 416-445
Author(s):  
Eyyüb Karakan ◽  
Selim Altun
Keyword(s):  
Cyclic Loading ◽  
Pore Water ◽  
Pore Water Pressure ◽  
Water Pressure ◽  
Triaxial Tests ◽  
Loading Conditions ◽  
Systematic Testing ◽  
Geotechnical Problems ◽  
Insight Into

Liquefaction may be triggered by cyclic loading on saturated silty sands, which is responsible of severe geotechnical problems. Development of excess pore water pressure in soil results in a liquid-like behavior and may be the reason of unavoidable superstructural damage. In this study, in order to investigate the behavior of saturated silty sands exposed to cyclic loading under undrained conditions, a systematic testing program of stress-controlled cyclic triaxial tests was performed on specimens of different silt contents, under different loading conditions and environment. The effect of parameters such as silt content on the liquefaction behavior of specimens was studied. Pore water pressure and shear strain curves were obtained for the silty sands. Furthermore, the boundaries existing in the literature on sands are compared with the results current research, on silty sands. Conclusively, the outcomes of this study were useful to develop insight into the behavior of clean and silty sands under seismic loading conditions.

TIME TO THE END OF PRIMARY CONSOLIDATION (EOP) OF SOFT CLAYEY SOILS: CONCERNING THE EFFECT OF ATTERBERG’S LIMIT AND CYCLIC LOADING HISTORY

2019 ◽  
Vol 128 (2B) ◽  
pp. 29-41
Author(s):  
Trần Thanh Nhàn
Keyword(s):  
Cyclic Loading ◽  
Pore Water ◽  
Pore Water Pressure ◽  
Water Pressure ◽  
Clayey Soils ◽  
Loading History ◽  
Cyclic Shear ◽  
Wide Range ◽  
Primary Consolidation ◽  
Time Required

In order to observe the end of primary consolidation (EOP) of cohesive soils with and without subjecting to cyclic loading, reconstituted specimens of clayey soils at various Atterberg’s limits were used for oedometer test at different loading increments and undrained cyclic shear test followed by drainage with various cyclic shear directions and a wide range of shear strain amplitudes. The pore water pressure and settlement of the soils were measured with time and the time to EOP was then determined by different methods. It is shown from observed results that the time to EOP determined by 3-t method agrees well with the time required for full dissipation of the pore water pressure and being considerably larger than those determined by Log Time method. These observations were then further evaluated in connection with effects of the Atterberg’s limit and the cyclic loading history.

scholarly journals Mechanical response and pore pressure generation in granular filters subjected to uniaxial cyclic loading

2018 ◽  
Vol 55 (12) ◽  
pp. 1756-1768
Author(s):  
Jahanzaib Israr ◽  
Buddhima Indraratna
Keyword(s):  
Cyclic Loading ◽  
Pore Pressure ◽  
Pore Water ◽  
Mechanical Response ◽  
Pore Water Pressure ◽  
Axial Strain ◽  
Water Pressure ◽  
Internal Erosion ◽  
Excess Pore Water Pressure ◽  
Excess Pore

This paper presents results from a series of piping tests carried out on a selected range of granular filters under static and cyclic loading conditions. The mechanical response of filters subjected to cyclic loading could be characterized in three distinct phases; namely, (I) pre-shakedown, (II) post-shakedown, and (III) post-critical (i.e., the occurrence of internal erosion). All the permanent geomechanical changes such, as erosion, permeability variations, and axial strain developments, took place during phases I and III, while the specimen response remained purely elastic during phase II. The post-critical occurrence of erosion incurred significant settlement that may not be tolerable for high-speed railway substructures. The analysis revealed that a cyclic load would induce excess pore-water pressure, which, in corroboration with steady seepage forces and agitation due to dynamic loading, could then cause internal erosion of fines from the specimens. The resulting excess pore pressure is a direct function of the axial strain due to cyclic densification, as well as the loading frequency and reduction in permeability. A model based on strain energy is proposed to quantify the excess pore-water pressure, and subsequently validated using current and existing test results from published studies.

scholarly journals Soil liquefaction as an identification test

2019 ◽  
Vol 92 ◽  
pp. 08008
Author(s):  
Bozana Bacic ◽  
Ivo Herle
Keyword(s):  
Pore Water ◽  
Laboratory Testing ◽  
Pore Water Pressure ◽  
Water Pressure ◽  
Initial Density ◽  
Soil Liquefaction ◽  
Triaxial Tests ◽  
Cyclic Triaxial ◽  
Cyclic Triaxial Tests ◽  
Identification Test

Time-consuming and complicated investigations of soil liquefaction in cyclic triaxial tests are the most common way of laboratory analysis of this phenomenon. Moreover, the necessary equipment for the performance of cyclic triaxial tests is very expensive. Much simpler method for laboratory testing of the soil liquefaction has been developed at the Institute of Geotechnical Engineering at the TU Dresden. This method takes into account the pore water pressure build-up during cyclic shearing within a short time period. During the test, the soil sample is subjected to horizontal cyclic loading and the generated pore water pressure is measured. In the first series of these experiments, a dependence of the pore water pressure buildup on the initial density of soil could be observed, as expected. When comparing different soils, it is shown that the tendency to liquefaction depends also on the granulometric properties (e.g. grain size distribution) of the soil. The aim of the further development is to establish a simple identification test for laboratory testing of the soil liquefaction.

scholarly journals Implications of the principle of effective stress

2020 ◽  
Author(s):  
Gerd Gudehus
Keyword(s):  
Critical Phenomena ◽  
Pore Water ◽  
Effective Stress ◽  
Critical Points ◽  
Pore Water Pressure ◽  
Numerical Models ◽  
Water Pressure ◽  
Shear Bands ◽  
Triaxial Tests ◽  
Water Saturated

AbstractWhile Terzaghi justified his principle of effective stress for water-saturated soil empirically, it can be derived by means of the neutrality of the mineral with respect to changes of the pore water pressure $$p_w$$ p w . This principle works also with dilating shear bands arising beyond critical points of saturated grain fabrics, and with patterns of shear bands as relics of critical phenomena. The shear strength of over-consolidated clay is explained without effective cohesion, which results also from swelling up to decay, while rapid shearing of water-saturated clay can lead to a cavitation of pore water. The $$p_w$$ p w -neutrality is also confirmed by triaxial tests with sandstone samples, while Biot’s relation with a reduction factor for $$p_w$$ p w is contestable. An effective stress tensor is heuristically legitimate also for soil and rock with relics of critical phenomena, particularly for critical points with a Mohr–Coulomb condition. Therein, the $$p_w$$ p w -neutrality of the solid mineral determines the interaction of solid fabric and pore water, but numerical models are questionable due to fractal features.

EXPERIMENT STUDY ON DYNAMIC STRENGTH OF LOESS UNDER REPEATED LOAD

2008 ◽  
Vol 22 (31n32) ◽  
pp. 5825-5830 ◽  
Author(s):  
ZHENGHUA XIAO ◽  
BO HAN ◽  
HONGJIAN LIAO ◽  
AKENJIANG TUOHUTI
Keyword(s):  
Shear Strength ◽  
Pore Water ◽  
Pore Water Pressure ◽  
Axial Strain ◽  
Water Pressure ◽  
Dynamic Strength ◽  
Triaxial Tests ◽  
Dynamic Shear ◽  
Anisotropic Consolidation ◽  
Dynamic Shear Strength

A series of dynamic triaxial tests are performed on normal anisotropic consolidation and over anisotropic consolidation specimens of loess. Based on the test results, the variable regularity of dynamic shear stress, axial strain and pore water pressure of loess under dynamic loading are measured and analyzed. The influences of the dynamic shear strength and pore water pressure at different over consolidation ratio are analyzed. The relationship between dynamic shear strength and over consolidation ratio of loess is obtained. The evaluating standard of dynamic shear strength of loess is discussed. Meanwhile, how to determine the effective dynamic shear strength index of normal anisotropic consolidated loess is also discussed in this paper. Several obtained conclusions can be referenced for studying the dynamic shear strength of loess foundation.

scholarly journals Evaluation of local friction and pore-water pressure evolution along instrumented probes in saturated clay for large numbers of cycles

2019 ◽  
Vol 56 (12) ◽  
pp. 1953-1967
Author(s):  
Rawaz Dlawar Muhammed ◽  
Jean Canou ◽  
Jean-Claude Dupla ◽  
Alain Tabbagh
Keyword(s):  
Cyclic Loading ◽  
Pore Water ◽  
Pore Water Pressure ◽  
Water Pressure ◽  
Static Friction ◽  
Good Picture ◽  
Friction Resistance ◽  
Saturated Clay ◽  
Tip Resistance ◽  
Number Of Cycles

To investigate local friction mobilization along piles subjected to cyclic axial loadings, a calibration chamber experiment is presented based on the implementation of instrumented probes in specimens of saturated clay. Typical results obtained with a piezo-probe are presented, allowing not only tip resistance and local friction to be measured, but also the local pore-water pressure developed on the probe shaft. In addition, specific piezometers installed in the clay specimen allow a good picture to be obtained of the pore-water pressure field around the probe during installation and loading. After installation of the probe, a succession of monotonic and cyclic displacement-controlled loading phases is applied. Upon displacement-controlled cyclic loading of the piezo-probe up to a very large number of cycles (105 cycles), an initial degradation of local friction is observed followed by a subsequent reinforcement, which continues until the end of the cyclic sequence. The friction evolution is related to the evolution of the pore-water pressure measured during cyclic loading. In particular, the influence of the cyclic loading sequence on the post-cyclic static friction resistance is evaluated. A comparison is finally made with the results obtained with another type of probe, showing a good consistency between both types of results.

Sign in / Sign up

Export Citation Format

Share Document