Influence of Process Parameters on Microstructure of Friction Stir Processed Mg AZ31 Alloy

2014 ◽  
Vol 2 (1) ◽  
pp. 47-58
Author(s):  
G. Venkateswarlu ◽  
M.J. Davidson ◽  
G.R.N. Tagore ◽  
P. Sammaiah
Keyword(s):  
Plastic Deformation ◽  
Grain Refinement ◽  
Process Parameters ◽  
Tilt Angle ◽  
Friction Stir Processing ◽  
Rotational Speed ◽  
Traverse Speed ◽  
Homogeneous Microstructure ◽  
Influence Of Process Parameters ◽  
Friction Stir

Friction stir processing (FSP) has been developed on the principles of friction stir welding (FSW) as an effective and efficien new method for grain refinement and microstructural modification, providing intense plastic deformation as well as higher strain rates than other conventional severe plastic deformation methods. FSP produces an equiaxed homogeneous microstructure consisting of fine grains, resulting in the enhancement of the properties of the material at room temperature. The objective of the present paper is to examine the influence of friction stir processing (FSP) parameters namely tool rotational speed (RS), tool traverse speed (TS) and tool tilt angle (TA) on the microstructures of friction stir processed AZ31B-O magnesium alloy. This investigation has focused on the microstructural changes occurred in the dynamically recrystallised nugget zone/ stir zone and the thermo mechanically affected zone during FSP. The results presented in this work indicate that all the three FSP process parameters have a significant effect on the resulting microstructure and also found that the rotational speed has greatly influenced the homogenization of the material. The grain refinement is higher at intermediate rotational speed (1150 rpm), traverse speed (32 mm / min and tilt angle (10). It is established that FSP can be a good grain refinement method for improving the properties of the material.

Influence of Process Parameters on Microstructure of Friction Stir Processed Mg AZ31 Alloy

2017 ◽  
pp. 1293-1305
Author(s):  
G. Venkateswarlu ◽  
M.J. Davidson ◽  
G.R.N. Tagore ◽  
P. Sammaiah
Keyword(s):  
Plastic Deformation ◽  
Grain Refinement ◽  
Process Parameters ◽  
Tilt Angle ◽  
Friction Stir Processing ◽  
Rotational Speed ◽  
Traverse Speed ◽  
Homogeneous Microstructure ◽  
Friction Stir ◽  
Tool Tilt Angle

Friction stir processing (FSP) has been developed on the principles of friction stir welding (FSW) as an effective and efficien new method for grain refinement and microstructural modification, providing intense plastic deformation as well as higher strain rates than other conventional severe plastic deformation methods. FSP produces an equiaxed homogeneous microstructure consisting of fine grains, resulting in the enhancement of the properties of the material at room temperature. The objective of the present paper is to examine the influence of friction stir processing (FSP) parameters namely tool rotational speed (RS), tool traverse speed (TS) and tool tilt angle (TA) on the microstructures of friction stir processed AZ31B-O magnesium alloy. This investigation has focused on the microstructural changes occurred in the dynamically recrystallised nugget zone/ stir zone and the thermo mechanically affected zone during FSP. The results presented in this work indicate that all the three FSP process parameters have a significant effect on the resulting microstructure and also found that the rotational speed has greatly influenced the homogenization of the material. The grain refinement is higher at intermediate rotational speed (1150 rpm), traverse speed (32 mm / min and tilt angle (10). It is established that FSP can be a good grain refinement method for improving the properties of the material.

scholarly journals Influence of Friction Stir Processing Parameters on Mg ZE 41-SiC Surface Composite

2019 ◽  
Vol 8 (2) ◽  
pp. 6058-6061
Keyword(s):  
Process Parameters ◽  
Tilt Angle ◽  
Friction Stir Processing ◽  
Rotational Speed ◽  
Traverse Speed ◽  
Nano Particles ◽  
Micro Hardness ◽  
Friction Stir ◽  
Surface Composite ◽  
Tool Tilt Angle

In this study, the influence of friction stir processing process parameters (FSP), such as tool rotational speed, tool traverse speed, and the tool tilt angle on the mechanical properties of Sic reinforced surface magnesium rare earth ZE41 alloy composite was studied. The process was carried at tool rotational speeds of 710, 900, 1120, 1600, 1400 and 1800 rpm, tool traverse speeds of 16, 25, 40 and 63 mm/min and tool tilt angle of degree 1. Nano-particles of SiC (40 microns) were used as reinforcements to produce a composite surface. The grain refinement of the processed specimens was analyzed using scanning electron microscope. It is observed from the results that FSP process parameters influenced the surface composite area, SiC particles distribution and micro hardness of the composite. The outcomes indicated that the higher micro hardness was obtained at rotational speed of 1100 RPM, traverse speed 40mm/min and tilt angle 10 .

scholarly journals Process Parameters Optimization for Producing AA6061/TiB2 Composites by Friction Stir Processing

2017 ◽  
Vol 67 (1) ◽  
pp. 101-118 ◽  
Author(s):  
Dakarapu Rao Santha ◽  
Nallu Ramanaiah
Keyword(s):  
Mechanical Properties ◽  
Tensile Strength ◽  
Aluminium Alloy ◽  
Process Parameters ◽  
Friction Stir Processing ◽  
Rotational Speed ◽  
Single Variable ◽  
Influence Of Process Parameters ◽  
Percentage Reinforcement ◽  
Friction Stir

Abstract Friction stir processing (FSP) is solid state novel technique developed to refine microstructure and to improve the mechanical properties and be used to fabricate the aluminium alloy matrix composites. An attempt is made to fabricate AA6061/TiB2 aluminium alloy composite (AMCs) and the influence of process parameters like rotational speed, transverse feed, axial load and percentage reinforcement on microstructure and mechanical properties were studied. The microstructural observations are carried out and revealed that the reinforcement particles (TiB2) were uniformly dispersed in the nugget zone. The Tensile strength and Hardness of composites were evaluated. It was observed that tensile strength, and hardness were increased with increased the rotational speed and percentage reinforcement of particles. The process parameters were optimized using Taguchi analysis (Single Variable) and Grey analysis (Multi Variable). The most influential parameter was rotational speed in single variable method and multi variable optimization method. The ANOVA also done to know the percentage contribution of each parameter.

Procedure to find out the optimal ranges of process parameters for friction stir welding

2021 ◽  
pp. 146442072199314
Author(s):  
Shubham Verma ◽  
Joy Prakash Misra ◽  
Meenu Gupta
Keyword(s):  
Friction Stir Welding ◽  
Process Parameters ◽  
Tilt Angle ◽  
Welding Speed ◽  
Rotational Speed ◽  
Optical Microscope ◽  
Graphical Analysis ◽  
Friction Stir ◽  
Steepest Ascent ◽  
Vertical Milling Machine

The present study deals with the application of sequential procedure (i.e. steepest ascent) to obtain the optimum values of process parameters for conducting friction stir welding (FSW) experiments. A vertical milling machine is modified by fabricating fixture and tool ( H13 material) for performing FSW operation to join AA7039 plates. The steepest ascent technique is employed to design the experiments at different rotational speed, welding speed, and tilt angle. The ultimate tensile strength is considered as a performance characteristic for deciding the optimal levels. The mechanical and metallurgical characteristics of the joints are studied by executing tensile and microhardness tests. It is concluded from the graphical analysis of the steepest ascent technique that the optimal maximum and minimum values are 1812–1325 r/min for rotational speed, 43–26 mm/min for welding speed, and 2°–1.3° for tilt angle, respectively. Besides, optical microscope and scanning electron microscope are utilized for microstructural and fractographic analyses for a better understanding of the process.

Fabrication and characterization of friction stir processed Al 6061 reinforced with TiB2-Al2O3

2020 ◽  
Vol ahead-of-print (ahead-of-print) ◽  
Author(s):  
Ch. Mohana Rao ◽  
K. Mallikarjuna Rao
Keyword(s):  
Mechanical Properties ◽  
Aluminum Alloy ◽  
Process Parameters ◽  
Friction Stir Processing ◽  
Practical Implication ◽  
Research Work ◽  
Influence Of Process Parameters ◽  
Volume Percentage ◽  
Content Type ◽  
Friction Stir

PurposeThe objective of the paper is to evaluate the fabrication process and to study the influence of process parameters of friction stir processing of 6061-TiB2-Al2O3 Aluminum alloy surface composite on microhardness tensile strength, and microstructure.Design/methodology/approachFriction stir processing method is used for attaining the desired mechanical properties, and selectively processed reinforcements to fabricate the samples. The Taguchi technique was used to optimize rotational speed, travel speed and volume percentage of reinforcement particles to enhance the mechanical properties of 6061-TiB2-Al2O3 Aluminum alloy composite.FindingsThe fabrication of surface composites through FSP allows new inventions in terms of material with enhanced surface layers without changing the base metal.Practical implicationsTo examine the behavior of the surface of the composites in the different zones, the practical implication consists of the use of different characterization techniques like optical microscopy and scanning microscopy for microstructural behavior and the measurement of hardness and tensile tests for mechanical behavior.Originality/valueThe research work consists of tool design and process parameters, which can affect the final product (microstructural changes), and the performance of the modified surface layer behavior was studied and presented.

Friction Stir Processing: An Operational Method to Improve Ductility in Pure Copper

2013 ◽  
Vol 818 ◽  
pp. 14-19 ◽  
Author(s):  
Vahid Rezazadeh ◽  
Ali Sharbatzadeh ◽  
Ali Hosseinzadeh ◽  
Amir Safari ◽  
Salar Salahi
Keyword(s):  
Friction Stir Processing ◽  
Rotational Speed ◽  
Pure Copper ◽  
Traverse Speed ◽  
Ultrafine Grain ◽  
Work Piece ◽  
Cavity Formation ◽  
Nugget Zone ◽  
Friction Stir ◽  
Lower Heat

mproving ductility in metals using friction stir processing (FSP) is a challenging effort and is made by means of a rotating tool inserted in a work piece providing heat transfer and plastic deformation. In this investigation, improving ductility during FSP was determined as a purpose and the microstructure and mechanical properties of nugget zone were investigated during friction stir processing (FSP) of pure copper. Ductility was measured using tensile elongations at a temperature of 20 °C. By varying the traverse speed from 40 to 100 mm/min at rotation speeds of 300 and 600 rpm, the ultrafine grain microstructure was achieved .Defects were observed in rotational speed of 300 rpm. By increasing traverse speed at constant rotational speed of 600 rpm grain size of the nugget zone decreased and ductility increased. Achievable ductility was limited by cavity formation due to lower heat input and deformation in samples with defects.

Optimization of friction stir welding process parameters for AA6063-ETP copper using central composite design

2020 ◽  
Vol 17 (4) ◽  
pp. 491-507 ◽  
Author(s):  
Nitin Panaskar ◽  
Ravi Prakash Terkar
Keyword(s):  
Experimental Data ◽  
Tensile Strength ◽  
Friction Stir Welding ◽  
Process Parameters ◽  
Rotational Speed ◽  
Traverse Speed ◽  
Tool Rotational Speed ◽  
Content Type ◽  
Friction Stir ◽  
Central Composite

Purpose Recently, several studies have been performed on lap welding of aluminum and copper using friction stir welding (FSW). The formation of intermetallic compounds at the weld interface hampers the weld quality. The use of an intermediate layer of a compatible material during welding reduces the formation of intermetallic compounds. The purpose of this paper is to optimize the FSW process parameters for AA6063-ETP copper weld, using a compatible zinc intermediate filler metal. Design/methodology/approach In the present study, a three-level, three-factor central composite design (CCD) has been used to determine the effect of various process parameters, namely, tool rotational speed, tool traverse speed and thickness of inter-filler zinc foil on ultimate tensile strength of the weld. A total of 60 experimental data were fitted in the CCD. The experiments were performed with tool rotational speeds of 1,000, 1,200 and 1,400 rpm each of them with tool traverse speeds of 5, 10 and 15 mm/min. A zinc inter-filler foil of 0.2 and 0.4 mm was also used. The macrograph of the weld surface under different process parameters and the tensile strength of the weld have been investigated. Findings The feasibility of joining 3 mm thick AA6063-ETP copper using zinc inter-filler is established. The regression analysis showed a good fit of the experimental data to the second-order polynomial model with a coefficient of determination (R2) value of 0.9759 and model F-value of 240.33. A good agreement between the prediction model and experimental findings validates the reliability of the developed model. The tool rotational speed, tool traverse speed and thickness of inter-filler zinc foil significantly affected the tensile strength of the weld. The optimal conditions found for the weld were, rotational speed of 1,212.83 rpm and traverse speed of 9.63 mm/min and zinc foil thickness is 0.157 mm; by using optimized values, ultimate tensile strength of 122.87 MPa was achieved, from the desirability function. Originality/value Aluminium and copper sheets could be joined feasibly using a zinc inter-filler. The maximum tensile strength of joints formed by inter-filler (122.87 MPa) was significantly better as compared to those without using inter-filler (83.78 MPa). The optimum process parameters to achieve maximum tensile strength were found by CCD.

Effect of Tool Rotational Speed on Microstructure and Microhardness of AA6082/TiC Surface Composites using Friction Stir Processing

2014 ◽  
Vol 592-594 ◽  
pp. 234-239 ◽  
Author(s):  
A. Thangarasu ◽  
N. Murugan ◽  
I. Dinaharan ◽  
S.J. Vijay
Keyword(s):  
Friction Stir Processing ◽  
Rotational Speed ◽  
Traverse Speed ◽  
Tool Rotational Speed ◽  
Friction Stir ◽  
Surface Composite ◽  
Surface Composites ◽  
Homogenous Distribution ◽  
Tool Pin ◽  
Scanning Electron

Friction stir processing (FSP) is as a novel modifying technique to synthesize surface composites. An attempt has been made to synthesis AA6082/TiC surface composite using FSP and to analyze the effect of tool rotational speed on microstructure and microhardness of the same. The tool rotational speed was varied from 800 rpm to 1600 rpm in steps of 400 rpm. The traverse speed, axial force, groove width and tool pin profile were kept constant. Scanning electron microscopy was employed to study the microstructure of the fabricated surface composites. The results indicated that the tool rotational speed significantly influenced the area of the surface composite and distribution of TiC particles. Higher rotational speed provided homogenous distribution of TiC particles while lower rotational speed caused poor distribution of TiC particles in the surface composite. The effect of the tool rotational speed on microhardness is also reported in this paper.

Effect of Process Parameters on Defect Formation in Friction Stir Processed 6082-T6 Aluminium Alloy

2012 ◽  
Vol 232 ◽  
pp. 3-7
Author(s):  
Akinlabi Esther Titilayo ◽  
Akinlabi Stephen Akinwale
Keyword(s):  
Tensile Strength ◽  
Ultimate Tensile Strength ◽  
Aluminium Alloy ◽  
Process Parameters ◽  
Friction Stir Processing ◽  
Feed Rate ◽  
Rotational Speed ◽  
Defect Formation ◽  
Processing Parameters ◽  
Friction Stir

This paper reports the effects of processing parameters on defects formed during friction stir processing of 6082-T6 Aluminium Alloy. The plates were processed by varying the feed rate between 50 and 250 mm/min, while the rotational speed was varied between 1500 and 3500 rpm to achieve the best result. It was observed that the sheets processed at the highest feed rate considered in this research resulted in wormhole defect. These processed samples with defects were correlated to the tensile results and it was found that the Ultimate Tensile Strength (UTS) of these samples was relatively low compared to other samples without defects.

scholarly journals Surface modification of Aluminium alloy (7xxx series) by multipass friction stir processing

2021 ◽  
Vol 6 (2) ◽  
pp. 008-017
Author(s):  
P K Mandal
Keyword(s):  
Mechanical Properties ◽  
Surface Modification ◽  
Process Parameters ◽  
Friction Stir Processing ◽  
Rotational Speed ◽  
Aluminium Alloys ◽  
Research Work ◽  
Dendritic Structure ◽  
Similar Process ◽  
Friction Stir

Multipass friction stir processing (MP-FSP) is a solid-state surface modification technique, which was developed based on the simple principle of FSW. Aluminium plates were subjected to MP-FSP from 1 to 14 passes along the longitudinal direction with the specified process parameters such as rotational speed of 1000 rpm and travel speed of 70 mm/min and axial force of 15 kN. Subsequently, similar process parameters had followed by doublepass friction stir processing (DP-FSP) in order to help determine the effectiveness of multipass in creating high strength of aluminium alloys. Now-a-days extensive research had focused on various process parameters such as rotational speed, traverse speed, tool design on processing of aluminium alloys and proficiently enhanced material properties. This technique has considered mostly development of green technology, which is energy efficient and environment friendly technique. Experimentally proven that the Al-Zn-Mg-Sc alloys are characterized through OM, FESEM, DSC, SEM, TEM, and mechanical properties. The tensile strength and ductility of the MP-FSP specimen improved significantly to 122.48%, and 42.55% respectively, but hardness decline to 4.84% as compared to DP-FSP. This is due to not only for refinement of cast dendritic structure and eliminate segregation in the as-cast alloy, but also to the refining of grains, such as the uniform distribution of Al3Sc and hardening precipitates. To aim of this research work is to mainly focusing on MP-FSP may enhance mechanical properties better than DP-FSP and useful for macroscale applications.

Sign in / Sign up

Export Citation Format

Share Document