Finite Element Analysis of External Prestressing Beams Made of Strain Hardening Material

2012 ◽  
Vol 166-169 ◽  
pp. 259-268 ◽  
Author(s):  
Ahmed Atta
Keyword(s):  
Finite Element Analysis ◽  
Finite Element ◽  
Strain Hardening ◽  
High Performance ◽  
Concrete Strength ◽  
Element Model ◽  
Element Analysis ◽  
Hardening Material ◽  
External Prestressing ◽  
Prestressing Tendon

The use of finite element analysis has been widely used as a means to analyze individual elements and the effects of concrete strength under loading. This paper is a study of prestressed concrete beams made of strain hardening material called UHP-SHCC (Ultra High Performance Strain Hardening Cementitious Composite) using finite element analysis to understand their response. A finite element model is studied and compared to experimental data. The basic parameters included second order effect of prestressed beam, and prestressing tendon depths have been considered in the analysis. The present study indicated the following conclusions: the number of deviators significantly influences the ultimate capacity and the strains values of UHP-SHCC beams, the change of external prestressing tendon depth has a significant effect on the cracking load, failure load, deflection values, and ultimate stress in the tendon in case of using UHP-SHCC beams but keep the final mode of failure without change.

Finite Element Analysis on Contact Surface Slip of Profiled Steel Sheet and Composite Slab

2012 ◽  
Vol 568 ◽  
pp. 256-259
Author(s):  
Li Liu ◽  
Fang Wang ◽  
Kai Wang
Keyword(s):  
Numerical Simulation ◽  
Finite Element Analysis ◽  
Finite Element ◽  
Steel Sheet ◽  
Concrete Strength ◽  
Element Model ◽  
Element Analysis ◽  
Composite Slab ◽  
Calculation Results ◽  
Bonding Surface

In order to evaluate correctly the load-bearing performance of the prestressed profiled steel sheet composite slab，according to actual loading conditions, finite element model of the prestressed profiled steel sheet and concrete composite slab is established. Numerical simulation is made to the slip of the prestressed composite slab. The calculation results show that the slip of the prestressed composite slab at ultimate status will be gradually reduced with the improvement of the concrete strength. When increasing the prestress, the slip value at ultimate status will be less reduced and increasing the thickness of the concrete can reduce the slip value at ultimate status, the deformation of the prestressed composite slab will be increased by over 10% when considering the slip of the bonding surface.

A Finite Element Analysis on Metal Ball Effect on Dynamics of a Ball Bearing

2018 ◽  
Vol 875 ◽  
pp. 100-104
Author(s):  
Bo Wun Huang ◽  
Jia Sheng Chen ◽  
Zhi Yin Huang ◽  
Nan Wen Lin
Keyword(s):  
Finite Element Analysis ◽  
Finite Element ◽  
Dynamic Characteristic ◽  
High Performance ◽  
Ball Bearing ◽  
Dynamic Properties ◽  
Element Model ◽  
Element Analysis ◽  
Rotating Speed ◽  
The Finite Element Analysis

The bearings are widely used in the rotating machinery systems to support the mechanical, structural for system. In a high rotating speed, the spindle to be stable rotating is dependent on a high performance bearing. Therefore, the dynamic characteristic of a ball bearing is very importance and need to study. In this work, the dynamic characteristic of a ball bearing is focused to study. Because the geometric of ball bearing are so complex, the finite element analysis is employed to investigate. By using the finite element analysis software ANSYS, the bearings meshed model can be setup. The dynamic properties, natural frequency and mode shape of ball and global system, can be studied to improve the high spindle rotating stable performance. Numerical indicates that the stress, strain and dynamics of the ball bearing system can be investigated in this finite element model.

Finite Element Analysis of Nonuniformity of Tires with Imperfections5

2007 ◽  
Vol 35 (3) ◽  
pp. 226-238 ◽  
Author(s):  
K. M. Jeong ◽  
K. W. Kim ◽  
H. G. Beom ◽  
J. U. Park
Keyword(s):  
Finite Element Analysis ◽  
Finite Element ◽  
Three Dimensional ◽  
Element Model ◽  
Radial Force ◽  
Element Analysis ◽  
The Finite Element Analysis ◽  
Dimensional Finite Element ◽  
Force Variation ◽  
Three Dimensional Finite Element

Abstract The effects of variations in stiffness and geometry on the nonuniformity of tires are investigated by using the finite element analysis. In order to evaluate tire uniformity, a three-dimensional finite element model of the tire with imperfections is developed. This paper considers how imperfections, such as variations in stiffness or geometry and run-out, contribute to detrimental effects on tire nonuniformity. It is found that the radial force variation of a tire with imperfections depends strongly on the geometrical variations of the tire.

scholarly journals Comparison of Tooth- and Bone-Borne Appliances on the Stress Distributions and Displacement Patterns in the Facial Skeleton in Surgically Assisted Rapid Maxillary Expansion—A Finite Element Analysis (FEA) Study

Materials ◽  
2021 ◽  
Vol 14 (5) ◽  
pp. 1152
Author(s):  
Rafał Nowak ◽  
Anna Olejnik ◽  
Hanna Gerber ◽  
Roman Frątczak ◽  
Ewa Zawiślak
Keyword(s):  
Finite Element Analysis ◽  
Finite Element ◽  
Three Dimensional ◽  
Element Model ◽  
Rapid Maxillary Expansion ◽  
Stress Distributions ◽  
Maxillary Expansion ◽  
Facial Skeleton ◽  
Element Analysis ◽  
Maxillary Constriction

The aim of this study was to compare the reduced stresses according to Huber’s hypothesis and the displacement pattern in the region of the facial skeleton using a tooth- or bone-borne appliance in surgically assisted rapid maxillary expansion (SARME). In the current literature, the lack of updated reports about biomechanical effects in bone-borne appliances used in SARME is noticeable. Finite element analysis (FEA) was used for this study. Six facial skeleton models were created, five with various variants of osteotomy and one without osteotomy. Two different appliances for maxillary expansion were used for each model. The three-dimensional (3D) model of the facial skeleton was created on the basis of spiral computed tomography (CT) scans of a 32-year-old patient with maxillary constriction. The finite element model was built using ANSYS 15.0 software, in which the computations were carried out. Stress distributions and displacement values along the 3D axes were found for each osteotomy variant with the expansion of the tooth- and the bone-borne devices at a level of 0.5 mm. The investigation showed that in the case of a full osteotomy of the maxilla, as described by Bell and Epker in 1976, the method of fixing the appliance for maxillary expansion had no impact on the distribution of the reduced stresses according to Huber’s hypothesis in the facial skeleton. In the case of the bone-borne appliance, the load on the teeth, which may lead to periodontal and orthodontic complications, was eliminated. In the case of a full osteotomy of the maxilla, displacements in the buccolingual direction for all the variables of the bone-borne appliance were slightly bigger than for the tooth-borne appliance.

Finite Element Analysis and Optimization of Long-Span Gantry NC Machining Center Structure

2011 ◽  
Vol 346 ◽  
pp. 379-384
Author(s):  
Shu Bo Xu ◽  
Yang Xi ◽  
Cai Nian Jing ◽  
Ke Ke Sun
Keyword(s):  
Finite Element Analysis ◽  
Finite Element ◽  
Design Method ◽  
Dynamic Performance ◽  
Plate Thickness ◽  
Element Model ◽  
Wall Structure ◽  
Characteristic Analysis ◽  
Element Analysis ◽  
Dynamic Performance Analysis

The use of finite element theory and modal analysis theory, the structure of the machine static and dynamic performance analysis and prediction using optimal design method for optimization, the new machine to improve job performance, improve processing accuracy, shorten the development cycle and enhance the competitiveness of products is very important. Selected for three-dimensional CAD modeling software-UG NX4.0 and finite element analysis software-ANSYS to set up the structure of the beam finite element model, and then post on the overall structure of the static and dynamic characteristic analysis, on the basis of optimized static and dynamic performance is more superior double wall structure of the beam. And by changing the wall thickness and the thickness of the inner wall, as well as the reinforcement plate thickness overall sensitivity analysis shows that changes in these three parameters on the dynamic characteristics of post impact. Application of topology optimization methods, determine the optimal structure of the beam ultimately.

Evaluation of Compressive Strengths of HPS Plate Systems Stiffened with Trapezoidal Stiffeners

2013 ◽  
Vol 671-674 ◽  
pp. 1025-1028
Author(s):  
Dong Ku Shin ◽  
Kyungsik Kim
Keyword(s):  
Finite Element Analysis ◽  
Finite Element ◽  
High Performance ◽  
Nonlinear Finite Element ◽  
Linear Strain ◽  
Element Analysis ◽  
Geometric Imperfections ◽  
Eurocode 3 ◽  
Initial Geometric Imperfections ◽  
Plate System

The ultimate compressive strengths of high performance steel (HPS) plate system stiffened longitudinally by closed stiffeners have been investigated by the nonlinear finite element analysis. Both conventional and high performance steels were considered in models following multi-linear strain hardening constitutive relationships. Initial geometric imperfections and residual stresses were also incorporated in the analysis. Numerical results have been compared to compressive strengths from Eurocode 3 EN 1993-1-5 and FHWA-TS-80-205. It has been found that although use of Eurocode 3 EN 1993-1-5 and FHWA-TS-80-205 may lead to highly conservative design strengths when very large column slenderness parameters are encountered

scholarly journals Analysis for Wrinkling Behavior of Girth-Welded Line Pipe

1996 ◽  
Author(s):  
Luiz T. Souza ◽  
David W. Murray
Keyword(s):  
Finite Element Analysis ◽  
Finite Element ◽  
Finite Element Model ◽  
Internal Pressure ◽  
Experimental Test ◽  
Element Model ◽  
Element Analysis ◽  
Line Pipe ◽  
New Era ◽  
Analytical Tools

The paper presents results for finite element analysis of full-sized girth-welded specimens of line pipe and compares these results with the behavior exhibited by test specimens subjected to constant axial force, internal pressure and monotonically increasing curvatures. Recommendations for the ‘best’ type of analytical finite element model are given. Comparisons between the behavior predicted analytically and the observed behavior of the experimental test specimens are made. The mechanism of wrinkling is explained and the evolution of the deformed configurations for different wrinkling modes is examined. It is concluded that the analytical tools now available are sufficiently reliable to predict the behavior of pipe in a manner that was not previously possible and that this should create a new era for the design and assessment of pipelines if the technology is properly exploited by industry.

Sign in / Sign up

Export Citation Format

Share Document