Analysis of Slab and Beam’s Moment Influenced by Stiffness Ratio

2012 ◽  
Vol 166-169 ◽  
pp. 329-332
Author(s):  
Hai Xia Chen
Keyword(s):  
Finite Element Analysis ◽  
Beam Element ◽  
Main Beam ◽  
Secondary Beam ◽  
Stiffness Ratio ◽  
Analysis Software ◽  
Element Analysis ◽  
Calculation Process ◽  
Floor System ◽  
Factory Building

In this paper ,taking industrial factory building , the size of 33 * 19.8 m2 for example, analyzes Integral reinforced concrete floor system under the loads by Finite element analysis software ANSYS. In the calculation process, beam element is beam4, slab element is shell63, Changing the line stiffness ratio of beam and slab, main beam and secondary beam, researches of moment on the main beam and the secondary beam by means of line stiffness ratio. It is showed that , when the value of line stiffness ratio is more than 10, mid-span moment is fewer obviously with the Increasing K ; when the value of line stiffness ratio is between 2 and 5, mid-span moment is fewer, too; when the value of line stiffness ratio is shorter than 2, mid-span moment does almost not changed.

Design and Simulation Analysis for Power Plant Coal Storage Bunker Girder Structure

2013 ◽  
Vol 706-708 ◽  
pp. 488-491
Author(s):  
Hong Mei Fan ◽  
Yun Xu Shi
Keyword(s):  
Finite Element Analysis ◽  
Finite Element ◽  
Power Plant ◽  
Simulation Analysis ◽  
Secondary Beam ◽  
Analysis Software ◽  
Element Analysis ◽  
Main Structure ◽  
Design Requirements

The structure of the closed square storage bunker main, secondary beam are designed in detail, and has carried on the simulation using finite element analysis software ANSYS, results show that the main structure of the design to meet the design requirements.

Design Research of Steel Pipe Combination of Angle Steel Tower of XiYue 220kV Cross Section

2013 ◽  
Vol 470 ◽  
pp. 408-411 ◽  
Author(s):  
Yan Zhong Ju ◽  
Xiao Xu Fu ◽  
Neng Xian Zeng
Keyword(s):  
Finite Element Analysis ◽  
Cross Section ◽  
Design Research ◽  
Axial Stress ◽  
Steel Pipe ◽  
Stress Difference ◽  
Analysis Software ◽  
Element Analysis ◽  
The Finite Element Analysis ◽  
Angle Steel

Given the path situation of Xiyue substation 220kV four outlets project crossing Shunde waterway section,this article applies of Dao Heng tower full stress analysis software and the finite element analysis software ANSYS to two steel pipe combination of angle steel towers to carry on design research,contrast axial stress of two kinds of software,analyse the reasons of axial stress difference.

ANSYS Simply Supported Deep Beams Based on the Study of Mechanical Properties

2013 ◽  
Vol 351-352 ◽  
pp. 782-785
Author(s):  
Yong Bing Liu ◽  
Xiao Zhong Zhang
Keyword(s):  
Mechanical Properties ◽  
Finite Element Analysis ◽  
Mechanical Model ◽  
Work Performance ◽  
Deep Beam ◽  
Analysis Software ◽  
Deep Beams ◽  
Element Analysis ◽  
Simply Supported ◽  
Force Characteristics

Established the mechanical model of simply supported deep beam, calculation and analysis of simple supported deep beams by using finite element analysis software ANSYS, simulated the force characteristics and work performance of the deep beam. Provides the reference for the design and construction of deep beams.

Finite Element Analysis and Optimization of the Truss of Installing Wave-Maker Based on ANSYS

2013 ◽  
Vol 313-314 ◽  
pp. 1038-1041
Author(s):  
Shou Jun Wang ◽  
Xing Xiong ◽  
Chao Li
Keyword(s):  
Finite Element Analysis ◽  
Finite Element ◽  
Design Parameters ◽  
Analysis Software ◽  
Element Analysis ◽  
Large Span ◽  
The Finite Element Analysis ◽  
Wave Maker

According to uncertainty of the design parameters for large span truss of installing wave-maker, in order to avoid the waste of materials,the truss is analyzed based on the finite element analysis software ANSYS to find out its weaknesses and various parts of the deformation. On the premise of ensuring the intensity and stiffness, the weight of the truss is reduced by adjusting its sizes and selecting different profiles, so as to achieve the optimization of the truss of installing wave-maker.

Experimental Research on the Magnetic Field Sensitive Polymeric Actuator

2011 ◽  
Vol 287-290 ◽  
pp. 603-607
Author(s):  
Chun Lin Xia ◽  
Yang Fang Wu ◽  
Qian Qian Lu
Keyword(s):  
Magnetic Field ◽  
Finite Element Analysis ◽  
Finite Element ◽  
Energy Conversion ◽  
Experimental Research ◽  
Experimental Results ◽  
Deformation Characteristics ◽  
Analysis Software ◽  
Element Analysis ◽  
The Magnetic Field

Using domestic MFSP membrane as a medium of energy conversion, a kind of MFSP actuator was designed. The dedicated test equipment was constructed for experimental research, and the experimental results were given. The strip and circular MSFP membrane were analyzed qualitatively to obtain the deformation characteristics of membrane by finite element analysis software.

Incorporation of Spinal Flexibility Measurements Into Finite Element Analysis

1990 ◽  
Vol 112 (4) ◽  
pp. 481-483 ◽  
Author(s):  
Mack G. Gardner-Morse ◽  
Jeffrey P. Laible ◽  
Ian A. F. Stokes
Keyword(s):  
Experimental Data ◽  
Finite Element Analysis ◽  
Finite Element ◽  
Stiffness Matrix ◽  
Beam Element ◽  
Technical Note ◽  
Element Analysis ◽  
Spinal Motion ◽  
Spinal Flexibility

This technical note demonstrates two methods of incorporating the experimental stiffness of spinal motion segments into a finite element analysis of the spine. The first method is to incorporate the experimental data directly as a stiffness matrix. The second method approximates the experimental data as a beam element.

CAD/CAE on the Mould Plates of Vertical Type High-Pressure Grouting Machine

2012 ◽  
Vol 538-541 ◽  
pp. 2681-2684
Author(s):  
Zhi Cheng Huang
Keyword(s):  
Finite Element Analysis ◽  
Finite Element ◽  
High Pressure ◽  
3D Model ◽  
Stress And Strain ◽  
Analysis Software ◽  
Element Analysis ◽  
Pressure Grouting ◽  
Object Of Study

Took a type of ceramics for daily use vertical type high pressure grouting machine as the object of study, study the stress and strain of its upper and lower mould plates. Established their 3D model by CAD software Pro-E, and then import them into finite element analysis software to analysis the value and distribution of the stress and strain. The analysis results can provide some reference for design, and have some engineering and practical value.

Sign in / Sign up

Export Citation Format

Share Document