Fabrication of TiO2 Nanotube Arrays in Ethylene Glycol Electrolyte by the Electrochemical Anodization Method

2013 ◽  
Vol 302 ◽  
pp. 31-34 ◽  
Author(s):  
Rui Liu ◽  
Liang Sheng Qiang ◽  
Wein Duo Yang ◽  
Hsin Yi Liu
Keyword(s):  
Electron Microscopy ◽  
Ethylene Glycol ◽  
Tio2 Nanotube Arrays ◽  
Tio2 Nanotube ◽  
Electrochemical Anodization ◽  
Nanotube Arrays ◽  
Anodization Voltage ◽  
Good Uniformity ◽  
Anodization Method ◽  
Scanning Electron

Highly-ordered TiO2 nanotube arrays were successfully fabricated by electrochemical anodization of titanium. The morphology of TiO2 nanotube arrays, the length and pore size were represented by field emission scanning electron microscopy (FE-SEM). The parameters of various anodization including F- concentration, reaction temperature and anodization voltage were investigated in detail. The results show that as-prepared TiO2 nanotube arrays possess good uniformity and well-aligned morphology in mixture of ethylene glycol and 0.3 wt% NH4F electrolyte at 40 V for 25 °C. The growth rates of TiO2 nanotube arrays can show activation energy.

Electrochemically self-doped hierarchical TiO2 nanotube arrays for enhanced visible-light photoelectrochemical performance: an experimental and computational study

RSC Advances ◽  
2016 ◽  
Vol 6 (52) ◽  
pp. 46871-46878 ◽  
Author(s):  
Yue Yang ◽  
Jianjun Liao ◽  
Yanfang Li ◽  
Xiankun Cao ◽  
Na Li ◽  
...  
Keyword(s):  
Visible Light ◽  
Computational Study ◽  
Tio2 Nanotube Arrays ◽  
Tio2 Nanotube ◽  
Electrochemical Anodization ◽  
Nanotube Arrays ◽  
Photoelectrochemical Performance ◽  
Anodization Method

A two-step electrochemical anodization method was used to prepare typical hierarchical top-ring/bottom-tube TiO2 nanotube arrays (TNTAs).

TiO2 Nanowires/Nanobelts Originating from Anodically Grown Nanotube Arrays

2012 ◽  
Vol 463-464 ◽  
pp. 802-807 ◽  
Author(s):  
Hai Jun Tao ◽  
Jie Tao ◽  
Tao Wang ◽  
Zuo Guo Bao
Keyword(s):  
Electron Microscopy ◽  
Scanning Electron Microscopy ◽  
Ethylene Glycol ◽  
Field Emission ◽  
Special Structure ◽  
Nanotube Arrays ◽  
Anodization Voltage ◽  
Anodization Time ◽  
Chemical Etch ◽  
Scanning Electron

TiO2nanotube arrays have aroused great interest because of their enormous application in areas such as gas sensor, catalysts, biological materials, and solar cells. In this report, TiO2nanowires/nanobelts originating from TiO2 nanotube arrays are fabricated by simple anodization of Ti foils in ethylene glycol (EG) containing 0.25wt% NH4F. From the field emission scanning electron microscopy (FE-SEM) it is observed that the morphology of the special structure is influenced by anodization voltage, water content and anodization time. In these factors, small amount of water plays a very important role in making the special nanostructure. Moreover, a possible mechanism that showed a relationship between the formation of the special structure and electric field directed chemical etch is proposed.

scholarly journals Highly Ordered TiO2 Nanotube Arrays with Engineered Electrochemical Energy Storage Performances

Materials ◽  
2021 ◽  
Vol 14 (3) ◽  
pp. 510
Author(s):  
Wangzhu Cao ◽  
Kunfeng Chen ◽  
Dongfeng Xue
Keyword(s):  
Tio2 Nanotubes ◽  
Lithium Ion ◽  
Tio2 Nanotube Arrays ◽  
Tio2 Nanotube ◽  
Electrochemical Anodization ◽  
Nanotube Arrays ◽  
Free Standing ◽  
Structured Materials ◽  
Self Organized ◽  
Binder Free

Nanoscale engineering of regular structured materials is immensely demanded in various scientific areas. In this work, vertically oriented TiO2 nanotube arrays were grown by self-organizing electrochemical anodization. The effects of different fluoride ion concentrations (0.2 and 0.5 wt% NH4F) and different anodization times (2, 5, 10 and 20 h) on the morphology of nanotubes were systematically studied in an organic electrolyte (glycol). The growth mechanisms of amorphous and anatase TiO2 nanotubes were also studied. Under optimized conditions, we obtained TiO2 nanotubes with tube diameters of 70–160 nm and tube lengths of 6.5–45 μm. Serving as free-standing and binder-free electrodes, the kinetic, capacity, and stability performances of TiO2 nanotubes were tested as lithium-ion battery anodes. This work provides a facile strategy for constructing self-organized materials with optimized functionalities for applications.

scholarly journals Vertically Aligned Binder-Free TiO2 Nanotube Arrays Doped with Fe, S and Fe-S for Li-ion Batteries

Nanomaterials ◽  
2021 ◽  
Vol 11 (11) ◽  
pp. 2924
Author(s):  
Suriyakumar Dasarathan ◽  
Mukarram Ali ◽  
Tai-Jong Jung ◽  
Junghwan Sung ◽  
Yoon-Cheol Ha ◽  
...  
Keyword(s):  
Tio2 Nanotube Arrays ◽  
Tio2 Nanotube ◽  
Electrochemical Anodization ◽  
Nanotube Arrays ◽  
Kinetic Properties ◽  
Outer Diameter ◽  
Impregnation Method ◽  
Binder Free ◽  
Vertically Aligned ◽  
Discharge Capacities

Vertically aligned Fe, S, and Fe-S doped anatase TiO2 nanotube arrays are prepared by an electrochemical anodization process using an organic electrolyte in which lactic acid is added as an additive. In the electrolyte, highly ordered TiO2 nanotube layers with greater thickness of 12 μm, inner diameter of approx. 90 nm and outer diameter of approx. 170 nm are successfully obtained. Doping of Fe, S, and Fe-S via simple wet impregnation method substituted Ti and O sites with Fe and S, which leads to enhance the rate performance at high discharge C-rates. Discharge capacities of TiO2 tubes increased from 0.13 mAh cm−2(bare) to 0.28 mAh cm−2 for Fe-S doped TiO2 at 0.5 C after 100 cycles with exceptional capacity retention of 85 % after 100 cycles. Owing to the enhancement of thermodynamic and kinetic properties by doping of Fe-S, Li-diffusion increased resulting in remarkable discharge capacities of 0.27 mAh cm−2 and 0.16 mAh cm−2 at 10 C, and 30 C, respectively.

scholarly journals Formation of TiO2 Nanotubular Layers on Ti-6Al-4V Based Dental Implants for Inhibiting Biofilm Growth

2020 ◽  
Vol 32 (7) ◽  
pp. 1543-1548
Author(s):  
SLAMET ◽  
BOY M. BACHTIAR ◽  
PRASWASTI P.D.K. WULAN ◽  
BILLY APRIANTO ◽  
MUHAMMAD IBADURROHMAN
Keyword(s):  
Dental Implants ◽  
Calcination Temperature ◽  
Tio2 Nanotube Arrays ◽  
Tio2 Nanotube ◽  
Electrochemical Anodization ◽  
Nanotube Arrays ◽  
Biofilm Inhibition ◽  
Biofilm Growth ◽  
Promising Alternative

Modification of Ti-6Al-4V through electrochemical anodization method has been investigated on the purpose of generating TiO2 nanotube arrays (TiNTAs) on the surface of Ti-6Al-4V films. The as-anodized samples were calcined in an atmospheric furnace at various temperatures, in the range of 500-800 ºC. The evaluation of biofilm inhibition was performed by an in vitro method with Streptococcus mutans as a bacterium model. FE-SEM imaging confirmed the successful formation of TiO2 nanotube arrays while XRD results implied a phase transformation from anatase to rutile when the calcination temperature was around 600-650 ºC with average crystallite size of 18 nm. Calcination temperature is one of determining factors in the adjustment of crystallinity and morphology of TiO2, which in turn affects its capability to suppress biofilm formation. This study revealed that the best sample for biofilm inhibition was calcined at 600 ºC with a crystallite phase of mostly anatase. This sample managed to improve antibacterial activity of up to five times as compared to the unmodified Ti-6Al-4V. The output of this study is expected to give some insight on a promising alternative for preventing the formation of harmful biofilm on dental implants.

SELF-ORDERING ELECTROCHEMICAL SYNTHESIS OF TiO2 NANOTUBE ARRAYS: CONTROLLING THE NANOTUBE GEOMETRY AND THE GROWTH RATE

2011 ◽  
Vol 10 (01n02) ◽  
pp. 55-58 ◽  
Author(s):  
KRISHNA KANT ◽  
DUSAN LOSIC
Keyword(s):  
Growth Rate ◽  
Ethylene Glycol ◽  
Electrochemical Synthesis ◽  
The Self ◽  
Electrochemical Anodization ◽  
Nanotube Arrays ◽  
Anodization Voltage ◽  
Nanotube Array ◽  
Anodization Time ◽  
Nanotube Growth

We report the fabrication of highly ordered TiO 2 nanotube arrays employing electrochemical anodization of titanium using an organic electrolyte comprised of water, NH 4 F , and ethylene glycol. To achieve the self-ordering regime of TiO 2 nanotube growth and reliable fabrication optimal potential window between 80 and 100 V was determined. We show that anodization voltage can be used not only to control nanotube diameters (70–180 nm) but also to have impact on nanotube growth rate. The anodization voltage and anodization time were used to adjust the length of TiO 2 nanotube (thickness of nanotube layer). TiO 2 nanotube array films and self-supporting layers with thickness from < 5 μm to > 250 μm were routinely fabricated.

Sign in / Sign up

Export Citation Format

Share Document