Sorption of Methylene Blue and Acid Orange 7 onto Ananas comosus Peels and Leaves Based Activated Carbon

2013 ◽  
Vol 330 ◽  
pp. 112-116 ◽  
Author(s):  
Nabilah A. Lutpi ◽  
N. Najihah Jamil ◽  
C.K. Kairulazam C.K. Abdullah ◽  
Yee Shian Wong ◽  
Soon An Ong ◽  
...  
Keyword(s):  
Methylene Blue ◽  
Activated Carbon ◽  
Contact Time ◽  
Time Effect ◽  
Ananas Comosus ◽  
Acid Orange 7 ◽  
Initial Concentration ◽  
Adsorbent Dosage ◽  
Acid Orange ◽  
Percentage Removal

The adsorption of Methylene Blue (MB) and Acid Orange 7 (AO7) dye onto Ananas Comosus Mixed Peels and Leaves (ACMPL) were carried out by conducting four different parameters such as initial concentration, pH, dosage of adsorbent, and contact time. Effect of initial concentration for both dyes showed that higher initial concentration would take longer contact time to attain equilibrium due to higher amount of adsorbate molecules. The effect of pH showed highest percentage removal for MB is at pH 9 which is 95.81%. Meanwhile for AO7 the highest percentage removal is 31.06% at pH 3. The percentage removal of MB had reached the equilibrium at dosage 0.5g while AO7 keep increasing with the increment of adsorbent dosage. The percentage removal of MB and AO7 had increased until hour 2.5 which was from 72.5% to 86.93% and 19.441% to 36.89% respectively and reached equilibrium at 3 hour contact time.

scholarly journals Study Into Dynamic Behaviour of the Methylene Blue Adsorption on Activated Carbon

2021 ◽  
Vol 29 (48) ◽  
pp. 105-113
Author(s):  
Alica Pastierová ◽  
Maroš Sirotiak
Keyword(s):  
Methylene Blue ◽  
Activated Carbon ◽  
Contact Time ◽  
Dynamic Behaviour ◽  
Time Effect ◽  
Adsorption Kinetic ◽  
Optimum Conditions ◽  
Methylene Blue Adsorption ◽  
Initial Concentration ◽  
Pseudo Second Order

Abstract This paper presents a study into dynamic behaviour of the methylene blue adsorption (MB) on activated carbon. Effect of four parameters were studied: effect of the adsorbent dosage, effect of contact time, effect of pH, and effect of the initial concentration of methylene blue. The adsorption kinetic data were modelled using the pseudo-first and pseudo-second orders. Results show that, based on the experimental data, the pseudo-second order could be considered satisfactory. Thermodynamic parameters proved that adsorption of dye was spontaneous owing to increase in temperature and endothermic nature. Taguchi method was applied to determine the optimum conditions for removal of methylene blue by activated carbon. The optimum conditions were found to be pH = 7, contact time 60 min, initial concentration of MB 4 mg/L.

Adsorption Efficiency of Garcinia mangostana Linn. (GML) Shells Based Activated Carbon

2013 ◽  
Vol 330 ◽  
pp. 136-140
Author(s):  
Nabilah A. Lutpi ◽  
W.Fadhilah W.M. Khalik ◽  
C.K. Kairulazam C.K. Abdullah ◽  
Yee Shian Wong ◽  
Soon An Ong ◽  
...  
Keyword(s):  
Methylene Blue ◽  
Activated Carbon ◽  
Synthetic Dyes ◽  
Adsorption Efficiency ◽  
Acid Orange 7 ◽  
Garcinia Mangostana ◽  
Batch Mode ◽  
Acid Orange ◽  
Percentage Removal ◽  
Temperature Scanning

The objective of this study is to investigate the adsorption efficiency of Garcinia Mangostana Linn. (GML) shells based activated carbon using two synthetic dyes which are methylene blue and acid orange 7. The parameters which were studied in batch mode are the effect of contact time, initial dyes concentration, particle size, adsorbent dosage and temperature. Scanning Electron Microscope (SEM) was used to determine the physical characterization of GML. Base on the percentage removal results, the basic dye (Methylene blue) depicts better performance if compared to the acid dye (Acid orange 7) with approximately 90% of the best percentage removal of Methylene blue.

Preparation and Characterization of Textile Sludge-Based Activated Carbon for Dyes Removal

2016 ◽  
Vol 818 ◽  
pp. 250-253
Author(s):  
Nurul Atiqah Najlaa Yac’cob ◽  
Norzita Ngadi ◽  
Roshanida Abd Rahman
Keyword(s):  
Methylene Blue ◽  
Activated Carbon ◽  
Surface Area ◽  
Low Cost ◽  
Reactive Black 5 ◽  
Adsorbent Dosage ◽  
Percentage Removal ◽  
Textile Sludge ◽  
Dyes Removal

An activated carbon derived from textile sludge was synthesized as an initiative of low cost adsorbent for removal of dyes. The surface area of this activated carbon was determined by Brunauer, Emmett and Teller (BET). From the BET results, it shows a high increment in the BET multi point area for textile sludge-activated carbon as compared to the textile sludge, which is 623.9557 m2/g and 58.9806 m2/g, respectively. The effects of initial adsorbent dosage were studied in the removal of Reactive Black 5 (RB5) and Methylene Blue (MB) dyes. RB5 and MB dyes solutions were used to represent anionic and cationic dyes respectively. It was concluded that the adsorbent dosage was proportional to the dyes removal for both RB5 and MB with percentage removal up to 99%.

scholarly journals Enhancing the Decolorization of Methylene Blue Using a Low-Cost Super-Absorbent Aided by Response Surface Methodology

Molecules ◽  
2021 ◽  
Vol 26 (15) ◽  
pp. 4430
Author(s):  
Nor Hakimin Abdullah ◽  
Mazlan Mohamed ◽  
Norshahidatul Akmar Mohd Shohaimi ◽  
Azwan Mat Lazim ◽  
Ahmad Zamani Abdul Halim ◽  
...  
Keyword(s):  
Methylene Blue ◽  
Response Surface Methodology ◽  
Activated Carbon ◽  
Response Surface ◽  
Oil Palm ◽  
Contact Time ◽  
Low Cost ◽  
Aqueous Media ◽  
Adsorbent Dosage ◽  
Oil Palm Trunk

The presence of organic dyes from industrial wastewater can cause pollution and exacerbate environmental problems; therefore, in the present work, activated carbon was synthesized from locally available oil palm trunk (OPT) biomass as a low-cost adsorbent to remove synthetic dye from aqueous media. The physical properties of the synthesized oil palm trunk activated carbon (OPTAC) were analyzed by SEM, FTIR-ATR, and XRD. The concurrent effects of the process variables (adsorbent dosage (g), methylene blue (MB) concentration (mg/L), and contact time (h)) on the MB removal percentage from aqueous solution were studied using a three-factor three-level Box–Behnken design (BBD) of response surface methodology (RSM), followed by the optimization of MB adsorption using OPTAC as the adsorbent. Based on the results of the analysis of variance (ANOVA) for the three parameters considered, adsorbent dosage (X1) is the most crucial parameter, with an F-value of 1857.43, followed by MB concentration (X2) and contact time (X3) with the F-values of 95.60 and 29.48, respectively. Furthermore, the highest MB removal efficiency of 97.9% was achieved at the optimum X1, X2, and X3 of 1.5 g, 200 mg/L, and 2 h, respectively.

scholarly journals Acid – treated activated carbon for phenolic compound removal in acid pre-treatment of lignocellulosic biomass for biogas production

2020 ◽  
Vol 10 (3) ◽  
pp. 5466-5471
Keyword(s):  
Activated Carbon ◽  
Gallic Acid ◽  
Phenolic Compound ◽  
Contact Time ◽  
Ph Value ◽  
Biogas Production ◽  
Coconut Shell ◽  
Initial Concentration ◽  
Adsorbent Dosage ◽  
Pre Treatment

Phenolic compound can be an inhibitor during acid pre-treatment process in the conversion of biomass into bioenergy and consequently reduces the production yield. Thus, this study aimed to investigate the potential use of activated carbon from coconut shell for phenolic compound removal and gallic acid was used as model phenolic. Granular activated carbon was treated by using 20% concentration of phosphoric acid to its properties and function. Acid treated and untreated activated carbon were characterized in term of morphology, surface functionalities and material phase by means of SEM, FT-IR and XRD. Few parameters that influenced the removal of gallic acid were studied which included the effect of adsorbent dosage, initial concentration, contact time, and pH. It is observed that the acid treated activated carbon was successfully remove the gallic acid for about 97% using of 0.5g/L adsorbent dosage, with initial concentration of 100 mg/L, at pH value of 4 and 150 minutes contact time. The adsorption behavior was fixed with Langmuir isotherm fixed the experiment data which indicates homogenous adsorption. These experimental results also revealed that coconut shell based activated carbon is viable cheaper adsorbent for phenolic compound removal.

scholarly journals Efficacy of Moringa oleifera Seed Husk as Adsorptive Agent for Trihalomethanes from a Water Treatment Plant in Southwestern, Nigeria

2020 ◽  
Vol 2020 ◽  
pp. 1-11
Author(s):  
Aderonke Adetutu Okoya ◽  
Olasunkanmi Olalekan Olaiya ◽  
Abimbola Bankole Akinyele ◽  
Nnenneh Oruada Ochor
Keyword(s):  
Activated Carbon ◽  
Water Treatment ◽  
Surface Water ◽  
Contact Time ◽  
Moringa Oleifera ◽  
Treatment Plant ◽  
Water Treatment Plant ◽  
Initial Concentration ◽  
Adsorbent Dosage ◽  
Seed Husk

Trihalomethanes (THMs) are formed when excess chlorine during chlorination of water reacts with organic material in water. They have mutagenic and carcinogenic properties. Moringa oleifera (MO) has found wide acceptance by many people in Nigeria who have used it for food for both humans and fauna, for health purposes, and as a coagulant for water treatment. However, the seed husks are currently discarded as waste and they have not been used as adsorbent to remove THMs from water. The physicochemical properties of both the treated and raw surface water were determined using standard methods, and the concentration of THMs was determined from the water treatment plant at different stages of treatment using gas chromatography with flame ionization detector (GC-FID). Recovery experiments were carried out to validate the procedure. The efficiencies of activated carbon of Moringa oleifera seed husk (MOSH) adsorbent for the removal of THMs in the water and as a coagulant for water treatment were also assessed. Batch adsorption experiments were carried out, and different parameters such as pH (5, 7, and 9), adsorbent dosage (0.2, 0.4, and 0.8 g), contact time (30, 60, and 90 minutes), and initial concentration (0.2, 0.4, and 0.6 mg/l) were optimized for the removal of trichloromethane and tribromomethane using the MOSH activated carbon. Experimental adsorption data from different initial concentrations of trichloromethane and tribromomethane were used to test conformity with Langmuir and Freundlich adsorption isotherms. The percentage recovery from our procedures ranged from 96.0 ± 1.41 to 100.0 ± 0.00 for trichloromethane while for tribromomethane the range was 60 ± 2.82 to 100.0 ± 0.00. The mean percentage adsorption efficiencies for the simulation experiment ranged from 34.365 ± 1.41 to 93.135 ± 0.57 and from 41.870 ± 0.27 to 94.655 ± 0.41 for trichloromethane and tribromomethane, respectively. The optimum conditions for both trichloromethane and tribromomethane were pH 9, 0.8 g adsorbent dosage, 60-minute contact time, and 0.6 mg/l initial concentration. The optimum values of these parameters used for the adsorption of the two THMs in the surface water serving the treatment plant gave an efficiency of 100.00 ± 0.00%. The turbidity values for the coagulation experiment reduced from 9.76 ± 0.03 NTU in the raw water before coagulation to 5.92 ± 0.13 NTU after coagulation while all other physicochemical parameters of the surface water decreased in value except conductivity and total dissolved solid which increased from 104.5 ± 3.54 to 108.0 ± 2.83 μS/cm and 63.00 ± 11.31 to 83.0 ± 8.49 mg/l, respectively. The experimental data best fit into Langmuir than Freundlich adsorption isotherm. The study concluded that MOSH activated carbon could serve as an adsorbent for the removal of THMs, calcium, and sulphur from water samples.

Granular activated carbon-biofilm configured sequencing batch reactor treatment of C.I. Acid Orange 7

2008 ◽  
Vol 76 (1) ◽  
pp. 142-146 ◽  
Author(s):  
Soon-An Ong ◽  
Eiichi Toorisaka ◽  
Makoto Hirata ◽  
Tadashi Hano
Keyword(s):  
Activated Carbon ◽  
Sequencing Batch Reactor ◽  
Batch Reactor ◽  
Granular Activated Carbon ◽  
Acid Orange 7 ◽  
Acid Orange

scholarly journals Possibility of Removing Phosphates from Activated Charbon Made from Date Kernels

2021 ◽  
Vol 06 (03) ◽  
Author(s):  
Nora Seghairi ◽  
Keyword(s):  
Activated Carbon ◽  
Natural Waters ◽  
Activated Carbons ◽  
Kinetic Studies ◽  
Phosphate Adsorption ◽  
Initial Concentration ◽  
Adsorbent Dosage ◽  
Isotherm Study ◽  
Freundlich Isotherms ◽  
Batch Tests

Phosphates in natural waters and whatever their origin, promote the formation of algae, reduce dissolved oxygen and reduce biodiversity in aquatic ecosystems. At high doses, phosphate salts can cause health problems. The objective of our study was to develop a simple, efficient and environmentally friendly sorption depollution technique on available and inexpensive media. We have studied the adsorption of phosphate on activated carbons prepared from date kernels. Batch tests were carried out in order to study different operating parameters such as the effect of contact time, pH, initial phosphate concentration and adsorbent dosage and adsorption kinetic. The sorption equilibrium was analyzed by Langmuir, Freundlich isotherms model. Results show that the phosphate adsorption was reversible and the quantity adsorbed reached its maximum value (14.49 mg/g) after 40 minutes. It was also found that phosphate uptake was affected by variation of pH, initial concentration of phosphate and activated carbon dosage. The adsorption improved with an acidic pH (pH = 6), initial concentration and adsorbent dosage. The results of kinetic studies revealed that adsorption phosphate on activated carbon based on date kernels (Biocar) and the intra-particle diffusion involved in the adsorption mechanism. Also, isotherm study showed that Langmuir isotherm best fit the data and the adsorption was a physical type.

Phase-controlled synthesis of bismuth oxide polymorphs for photocatalytic applications

2018 ◽  
Vol 2 (9) ◽  
pp. 1664-1673 ◽  
Author(s):  
Thangavel Selvamani ◽  
Sambandam Anandan ◽  
Luis Granone ◽  
Detlef W. Bahnemann ◽  
Muthupandian Ashokkumar
Keyword(s):  
Methylene Blue ◽  
Methyl Orange ◽  
Bismuth Oxide ◽  
Rhodamine B ◽  
Controlled Synthesis ◽  
Acid Orange 7 ◽  
Acid Orange ◽  
Photocatalytic Applications

Bismuth oxide polymorphs (β-Bi2O3 nanoparticles and α-Bi2O3 coral-like morphology) were synthesized and they show an enhanced efficacy for the degradation of rhodamine B and acid orange 7 as compared to that of methylene blue and methyl orange under simulated solar illumination.

Sign in / Sign up

Export Citation Format

Share Document