Preparation and Characterization of Textile Sludge-Based Activated Carbon for Dyes Removal

2016 ◽  
Vol 818 ◽  
pp. 250-253
Author(s):  
Nurul Atiqah Najlaa Yac’cob ◽  
Norzita Ngadi ◽  
Roshanida Abd Rahman
Keyword(s):  
Methylene Blue ◽  
Activated Carbon ◽  
Surface Area ◽  
Low Cost ◽  
Reactive Black 5 ◽  
Adsorbent Dosage ◽  
Percentage Removal ◽  
Textile Sludge ◽  
Dyes Removal

An activated carbon derived from textile sludge was synthesized as an initiative of low cost adsorbent for removal of dyes. The surface area of this activated carbon was determined by Brunauer, Emmett and Teller (BET). From the BET results, it shows a high increment in the BET multi point area for textile sludge-activated carbon as compared to the textile sludge, which is 623.9557 m2/g and 58.9806 m2/g, respectively. The effects of initial adsorbent dosage were studied in the removal of Reactive Black 5 (RB5) and Methylene Blue (MB) dyes. RB5 and MB dyes solutions were used to represent anionic and cationic dyes respectively. It was concluded that the adsorbent dosage was proportional to the dyes removal for both RB5 and MB with percentage removal up to 99%.

scholarly journals Optimisation of durian peel based activated carbon preparation conditions for dye removal

2013 ◽  
Vol 16 (1) ◽  
pp. 22-31
Author(s):  
Phung Thi Kim Le ◽  
Kien Anh Le
Keyword(s):  
Methylene Blue ◽  
Activated Carbon ◽  
Surface Area ◽  
Dye Removal ◽  
Activated Carbons ◽  
Low Cost ◽  
Waste Water Treatment ◽  
Impregnation Ratio ◽  
Carbon Production ◽  
Removal Capacity

Agricultural wastes are considered to be a very important feedstock for activated carbon production as they are renewable sources and low cost materials. This study present the optimize conditions for preparation of durian peel activated carbon (DPAC) for removal of methylene blue (MB) from synthetic effluents. The effects of carbonization temperature (from 673K to 923K) and impregnation ratio (from 0.2 to 1.0) with potassium hydroxide KOH on the yield, surface area and the dye adsorbed capacity of the activated carbons were investigated. The dye removal capacity was evaluated with methylene blue. In comparison with the commercial grade carbons, the activated carbons from durian peel showed considerably higher surface area especially in the suitable temperate and impregnation ratio of activated carbon production. Methylene blue removal capacity appeared to be comparable to commercial products; it shows the potential of durian peel as a biomass source to produce adsorbents for waste water treatment and other application. Optimize condition for preparation of DPAC determined by using response surface methodology was at temperature 760 K and IR 1.0 which resulted the yield (51%), surface area (786 m2/g), and MB removal (172 mg/g).

Sorption of Methylene Blue and Acid Orange 7 onto Ananas comosus Peels and Leaves Based Activated Carbon

2013 ◽  
Vol 330 ◽  
pp. 112-116 ◽  
Author(s):  
Nabilah A. Lutpi ◽  
N. Najihah Jamil ◽  
C.K. Kairulazam C.K. Abdullah ◽  
Yee Shian Wong ◽  
Soon An Ong ◽  
...  
Keyword(s):  
Methylene Blue ◽  
Activated Carbon ◽  
Contact Time ◽  
Time Effect ◽  
Ananas Comosus ◽  
Acid Orange 7 ◽  
Initial Concentration ◽  
Adsorbent Dosage ◽  
Acid Orange ◽  
Percentage Removal

The adsorption of Methylene Blue (MB) and Acid Orange 7 (AO7) dye onto Ananas Comosus Mixed Peels and Leaves (ACMPL) were carried out by conducting four different parameters such as initial concentration, pH, dosage of adsorbent, and contact time. Effect of initial concentration for both dyes showed that higher initial concentration would take longer contact time to attain equilibrium due to higher amount of adsorbate molecules. The effect of pH showed highest percentage removal for MB is at pH 9 which is 95.81%. Meanwhile for AO7 the highest percentage removal is 31.06% at pH 3. The percentage removal of MB had reached the equilibrium at dosage 0.5g while AO7 keep increasing with the increment of adsorbent dosage. The percentage removal of MB and AO7 had increased until hour 2.5 which was from 72.5% to 86.93% and 19.441% to 36.89% respectively and reached equilibrium at 3 hour contact time.

Characterization of the Corallina Elongata Alga and Study of its Biosorption Properties for Methylene Blue

2019 ◽  
Vol 41 (1) ◽  
pp. 62-62
Author(s):  
Farida Bouremmad Farida Bouremmad ◽  
Abdennour Bouchair Abdennour Bouchair ◽  
Sorour Semsari Parapari Sorour Semsari Parapari ◽  
Shalima Shawuti and Mehmet Ali Gulgun Shalima Shawuti and Mehmet Ali Gulgun
Keyword(s):  
Methylene Blue ◽  
Activated Carbon ◽  
Adsorption Capacity ◽  
Low Cost ◽  
Mediterranean Coast ◽  
Batch Adsorption ◽  
Maximum Adsorption Capacity ◽  
Aquatic Biomass ◽  
Equilibrium Data

Biosorbents can be an alternative to activated carbon. They are derived from agricultural by-products or aquatic biomass. They are low cost and they may have comparable performances to those of activated carbon. The present study focuses on the characterization of the Corallina Elongata (CE) alga and its adsorption performance for Methylene Blue (MB), this alga is found in abundance at the Mediterranean coast of the city of Jijel in eastern Algeria. The dried alga was characterized using various characterization techniques such as DTA, TG, FTIR, XRD, SEM and EDX, which showed that the material consists essentially of a calcite containing magnesium. Batch adsorption studies were carried out and the effect of experimental parameters Such as pH, initial dye concentration, temperature, adsorbent dose and contact time, on the adsorption of MB was studied. The kinetic experimental data were found to conform to the pseudo-second-order model with good correlation and equilibrium data were best fitted to The Langmuir model, with a maximum adsorption capacity of 34.4 mg/g. The adsorption isotherms at various temperatures allowed the determination of certain thermodynamic parameters (ΔG, ΔH and ΔS). Finally, the adsorption results showed a good affinity between CE and MB with a high adsorption capacity.

scholarly journals Preparation and Characterization of Activated Carbon from Lapsi (Choerospondias axillaris) Seed Stone by Chemical Activation with Potassium Hydroxide

2014 ◽  
Vol 9 (1) ◽  
pp. 79-88 ◽  
Author(s):  
Sahira Joshi ◽  
Bhadra Prasad Pokharel
Keyword(s):  
Methylene Blue ◽  
Activated Carbon ◽  
Potassium Hydroxide ◽  
Low Cost ◽  
Chemical Activation ◽  
Sem Images ◽  
Monolayer Adsorption ◽  
Ft Ir ◽  
Characterization Of Activated Carbon

Activated carbon (AC) was prepared from Lapsi seed stone by chemical activation with Potassium hydroxide at 400°C. The AC was characterized by pH, moisture content, Fourier transform-infrared (FTIR) spectroscopy, scanning electron microscopy (SEM), methylene blue (MB) and iodine (I2) number. FT-IR spectra indicated the presence of various oxygen containing functional groups on the surface of AC. SEM images show the highly porous characteristics of AC with full of cavities. The Iodine number of AC revealed that the AC was found to be highly micro-porous. The adsorption of methylene blue by prepared AC was analyzed by the Langmuir and Freundlich adsorption isotherms. The data fitted well to the Langmuir isotherm with monolayer adsorption capacity 158 mg/g. The analysis showed that the AC prepared from Lapsi seed stone activated with potassium hydroxide could be a low-cost adsorbent with favorable surface properties. DOI: http://dx.doi.org/10.3126/jie.v9i1.10673Journal of the Institute of Engineering, Vol. 9, No. 1, pp. 79–88

scholarly journals Enhancing the Decolorization of Methylene Blue Using a Low-Cost Super-Absorbent Aided by Response Surface Methodology

Molecules ◽  
2021 ◽  
Vol 26 (15) ◽  
pp. 4430
Author(s):  
Nor Hakimin Abdullah ◽  
Mazlan Mohamed ◽  
Norshahidatul Akmar Mohd Shohaimi ◽  
Azwan Mat Lazim ◽  
Ahmad Zamani Abdul Halim ◽  
...  
Keyword(s):  
Methylene Blue ◽  
Response Surface Methodology ◽  
Activated Carbon ◽  
Response Surface ◽  
Oil Palm ◽  
Contact Time ◽  
Low Cost ◽  
Aqueous Media ◽  
Adsorbent Dosage ◽  
Oil Palm Trunk

The presence of organic dyes from industrial wastewater can cause pollution and exacerbate environmental problems; therefore, in the present work, activated carbon was synthesized from locally available oil palm trunk (OPT) biomass as a low-cost adsorbent to remove synthetic dye from aqueous media. The physical properties of the synthesized oil palm trunk activated carbon (OPTAC) were analyzed by SEM, FTIR-ATR, and XRD. The concurrent effects of the process variables (adsorbent dosage (g), methylene blue (MB) concentration (mg/L), and contact time (h)) on the MB removal percentage from aqueous solution were studied using a three-factor three-level Box–Behnken design (BBD) of response surface methodology (RSM), followed by the optimization of MB adsorption using OPTAC as the adsorbent. Based on the results of the analysis of variance (ANOVA) for the three parameters considered, adsorbent dosage (X1) is the most crucial parameter, with an F-value of 1857.43, followed by MB concentration (X2) and contact time (X3) with the F-values of 95.60 and 29.48, respectively. Furthermore, the highest MB removal efficiency of 97.9% was achieved at the optimum X1, X2, and X3 of 1.5 g, 200 mg/L, and 2 h, respectively.

scholarly journals Methylene blue removal using prepared activated carbon from grape wood wastes: adsorption process analysis and modeling

2021 ◽  
Author(s):  
Seyyed Alireza Mousavi ◽  
Davood Shahbazi ◽  
Arezoo Mahmoudi ◽  
Parastoo Darvishi
Keyword(s):  
Methylene Blue ◽  
Activated Carbon ◽  
Process Analysis ◽  
Low Cost ◽  
Freundlich Isotherm ◽  
Isotherm Models ◽  
Water And Wastewater Treatment ◽  
Adsorbent Dosage ◽  
Initial Ph ◽  
Pseudo Second Order

Abstract An adsorption study has been conducted for activated carbon obtained from grape wood wastes to assess their capability to remove methylene blue (MB) from the aqueous solutions. The properties of prepared activated carbon were characterized using FTIR, BET and SEM analyses. The effects of independent variables such as initial concentration of MB (100–500 mg L−1), initial pH of solution (3–11), adsorbent dosage (0.25–12.25 g L−1) and contact time (10–90 min) on the MB adsorption have been optimized using response surface methodology. The highest MB removal efficiency was 98% when pH, MB and adsorbent dosage were 11, 100 mg L−1 and 12.25 g L−1, respectively. The experimental data have been tested using Langmuir and Freundlich isotherm models, and the achieved data were fully fitted with the Langmuir model (R2 = 0.99), which indicates the monolayer adsorption. The adsorption kinetics well followed by the pseudo-second-order model with R2 of 0.99. This prepared activated carbon as a low-cost and eco-friendly adsorbent can be used widely for water and wastewater treatment.

scholarly journals Preparation and characterization of activated carbons from different kinds of coal

2020 ◽  
pp. 25-31
Author(s):  
Batkhishig Damdin ◽  
Purevsuren Barnasan ◽  
Chung-Jun Lin ◽  
Batbileg Sanjaa ◽  
Ariunaa Alyeksandr
Keyword(s):  
Methylene Blue ◽  
Activated Carbon ◽  
Iodine Number ◽  
Surface Area ◽  
Pore Volume ◽  
Activated Carbons ◽  
Bet Surface Area ◽  
Water Steam ◽  
Initial Coal

Initial coal was purified in heavy liquid with a density 1.3 cm3 of ZnCl2 solution and purified coal was carbonized and the initial coal samples of each deposits were purified by pyrolysis. Thus, the yield of pyrolysis hard residue in the enriched sample was slightly higher than in the hard residue of initial coal. Therefore, pyrolysis hard residue of purified coal (carbonized sample) was activated at 800°C for 2 hours by preheated water steam. Activated carbons (ACs) and non-activated and non-carbonized coal from Baganuur, Ereen and Nariin Sukhait deposits were technically analyzed and their iodine number, BET surface area, pore volume and adsorption of methylene blue (MB) were determined. When these results were compared, these indicators increased 5-17 times in the Baganuur activated carbon (BN-AC), Ereen activated carbon (E-AC) and Nariin Sukhait activated carbon (NS-AC) as compared to inactivated coal.

Sign in / Sign up

Export Citation Format

Share Document