Pool Boiling of Nanofluids in Vertical Porous Media

2013 ◽  
Vol 388 ◽  
pp. 18-22 ◽  
Author(s):  
Ridho Irwansyah ◽  
Nandy Putra
Keyword(s):  
Heat Transfer ◽  
Heat Flux ◽  
Porous Media ◽  
Single Phase ◽  
Pool Boiling ◽  
High Heat ◽  
High Heat Flux ◽  
Sintered Copper ◽  
Order Of Magnitude ◽  
Screen Mesh

The development of electronic components such as microprocessor requires a better thermal management system to overcome the high heat flux produce by the component. The method to absorb the heat produce by the microprocessor is still use the conduction or either natural or free convection which still in a single phase heat transfer. One of heat transfer method that suitable for a high heat flux application is pool boiling which has a two order of magnitude higher than of a single phase heat transfer and does not require a pump to move the fluid. In this study has been conducted the pool boiling experiment with four different porous media surface which are sintered copper 300 µm and 400 µm, copper screen mesh and stainless steel screen mesh with four different fluid which are Al2O3-Water 1%, 3% and 5%. The sintered copper 400 µm has shown a better heat transfer performance compared to the other porous media. The Water, Al2O3-Water 5% has shown a performance no better than Al2O3-Water 1% and 3%.

Observations of the Critical Heat Flux Process During Pool Boiling of FC-72

2014 ◽  
Vol 136 (4) ◽  
Author(s):  
J. Jung ◽  
S. J. Kim ◽  
J. Kim
Keyword(s):  
Heat Transfer ◽  
Heat Flux ◽  
Critical Heat Flux ◽  
Pool Boiling ◽  
High Heat ◽  
Line Length ◽  
Boiling Curve ◽  
High Heat Flux ◽  
Transfer Coefficients ◽  
Ir Camera

Experimental work was undertaken to investigate the process by which pool-boiling critical heat flux (CHF) occurs using an IR camera to measure the local temperature and heat transfer coefficients on a heated silicon surface. The wetted area fraction (WF), the contact line length density (CLD), the frequency between dryout events, the lifetime of the dry patches, the speed of the advancing and receding contact lines, the dry patch size distribution on the surface, and the heat transfer from the liquid-covered areas were measured throughout the boiling curve. Quantitative analysis of this data at high heat flux and transition through CHF revealed that the boiling curve can simply be obtained by weighting the heat flux from the liquid-covered areas by WF. CHF mechanisms proposed in the literature were evaluated against the observations.

Dependence of Heat Transfer Coefficient on Porous Structure in Porous Media

2008 ◽  
Author(s):  
Akira Matsui ◽  
Kazuhisa Yuki ◽  
Hidetoshi Hashizume
Keyword(s):  
Heat Transfer ◽  
Heat Flux ◽  
Porous Media ◽  
Heat Transfer Coefficient ◽  
Transfer Coefficient ◽  
High Performance ◽  
Heat Removal ◽  
High Heat ◽  
Metal Foams ◽  
High Heat Flux

Detailed heat transfer characteristics of particle-sintered porous media and metal foams are evaluated to specify the important structural parameters suitable for high heat removal. The porous media used in this experiment are particle-sintered porous media made of bronze and SUS316L, and metal foams made of copper and nickel. Cooling water flows into the porous medium opposite to heat flux input loaded by a plasma arcjet. The result indicates that the bronze-particle porous medium of 100μm in pore size shows the highest performance and achieves heat transfer coefficient of 0.035MW/m2K at inlet heat flux 4.6MW/m2. Compared with the heat transfer performance of copper fiber-sintered porous media, the bronze particlesintered ones give lower heat transfer coefficient. However, the stable cooling conditions that the heat transfer coefficient does not depend on the flow velocity, were confirmed even at heat flux of 4.6MW/m2 in case of the bronze particle-sintered media, while not in the case of the copper-fiber sintered media. This signifies the possibility that the bronze-particle sintered media enable much higher heat flux removal of over 10MW/m2, which could be caused by higher permeability of the particle-sintered pore structures. Porous media with high permeability provide high performance of vapor evacuation, which leads to more stable heat removal even under extremely high heat flux. On the other hand, the heat transfer coefficient of the metal foams becomes lower because of the lower capillary and fin effects caused by too high porosity and low effective thermal conductivity. It is concluded that the pore structure having high performance of vapor evacuation as well as the high capillary and high fin effects is appropriate for extremely high heat flux removal of over 10MW/m2.

Enhanced Pool Boiling Performance on Micro-, Nano-, and Hybrid-Structured Surfaces

2011 ◽  
Author(s):  
Qian Li ◽  
Wei Wang ◽  
Chris Oshman ◽  
Benoit Latour ◽  
Chen Li ◽  
...  
Keyword(s):  
Heat Transfer ◽  
Heat Flux ◽  
Thermal Management ◽  
Pool Boiling ◽  
High Heat ◽  
High Heat Flux ◽  
Maximum Heat ◽  
Structured Surfaces ◽  
Maximum Heat Transfer ◽  
Functional Components

Thermal management plays an important role in both high power electronics and energy conversion systems. A key issue in thermal management is the dissipation of the high heat flux generated by functional components. In this paper, various microstructures, nanostructures and hybrid micro/nano-structures were successfully fabricated on copper (Cu) surfaces, and the corresponding pool boiling heat transfer performance was systematically studied. It is found that the critical heat flux (CHF) of hybrid structured surfaces is about 15% higher than that of the surfaces with nanowires only and micro-pillars only. More importantly, the superheat at CHF for the hybrid structured surface is much smaller than that of the micro-pillared surface (about 35%), and a maximum heat transfer coefficient (HTC) of about 90,000W/m2K is obtained. Compared with the known best pool boiling performance on biporous media, a much larger HTC and much lower superheat at a heat flux of 250W/cm2 have been obtained on the novel hybrid-structured surfaces.

Dropwise Condensation on Superhydrophobic Microporous Wick Structures

2018 ◽  
Vol 140 (7) ◽  
Author(s):  
Sean H. Hoenig ◽  
Richard W. Bonner
Keyword(s):  
Heat Transfer ◽  
Heat Flux ◽  
Contact Angle ◽  
Droplet Size ◽  
Copper Powder ◽  
Contact Angle Hysteresis ◽  
High Heat ◽  
Superhydrophobic Surfaces ◽  
High Heat Flux ◽  
Sintered Copper

Previous research in dropwise condensation (DWC) on rough microtextured superhydrophobic surfaces has demonstrated evidence of high heat transfer enhancement compared to smooth hydrophobic surfaces. In this study, we experimentally investigate the use of microporous sintered copper powder on copper substrates coated with a thiol-based self-assembled monolayer to attain enhanced DWC for steam in a custom condensation chamber. Although microtextured superhydrophobic surfaces have shown advantageous droplet growth dynamics, precise heat transfer measurements are underdeveloped at high heat flux. Sintered copper powder diameters from 4 μm to 119 μm were used to investigate particle size effects on heat transfer. As powder diameter decreased, competing physical factors led to improved thermal performance. At consistent operating conditions, we experimentally demonstrated a 23% improvement in the local condensation heat transfer coefficient for a superhydrophobic 4 μm diameter microporous copper powder surface compared to a smooth hydrophobic copper surface. For the smallest powders observed, this improvement is primarily attributed to the reduction in contact angle hysteresis as evidenced by the decrease in departing droplet size. Interestingly, the contact angle hysteresis of sessile water droplets measured in air is in contradiction with the departing droplet size observations made during condensation of saturated steam. It is evident that the specific design of textured superhydrophobic surfaces has profound implications for enhanced condensation in high heat flux applications.

High Heat Flux Dissipation Using Symmetric Dual-Taper Manifold in Pool Boiling

2019 ◽  
Author(s):  
Aranya Chauhan ◽  
Satish G. Kandlikar
Keyword(s):  
Heat Transfer ◽  
Heat Flux ◽  
Pool Boiling ◽  
Heat Removal ◽  
Heating Surface ◽  
High Heat ◽  
Copper Surface ◽  
High Heat Flux ◽  
Maximum Heat ◽  
Continuous Increase

Abstract The trend of miniaturization in electronics presents a great challenge in the thermal management of devices. The continuous increase in the number of transistors in the processor leads to high heat flux generation, limiting the performance of the device. Boiling heat transfer offers a great heat removal competency while maintaining the low chip temperatures. The critical heat flux (CHF) dictates the maximum heat removal ability, and heat transfer coefficient (HTC) defines the efficiency of the boiling process. This pool boiling study is focused on using a manifold containing a symmetric dual taper over the heating surface. The heat transfer performance of this configuration is evaluated for different taper angles in the manifold. The macro-convection assisted by vapor columns during boiling enhance the CHF and HTC limit significantly. A CHF of 287 W/cm2 with an HTC of 116 kW/cm2°C was achieved with a plain copper surface, representing greater than a 2-fold increases in each over a plain surface.

Experimental Study of Single Phase Heat Transfer and Pressure Loss in a Spiraling Radial Inflow Microchannel Heat Sink

2015 ◽  
Vol 137 (7) ◽  
Author(s):  
Maritza Ruiz ◽  
Van P. Carey
Keyword(s):  
Heat Transfer ◽  
Experimental Study ◽  
Heat Flux ◽  
Single Phase ◽  
High Heat ◽  
High Heat Flux ◽  
Transfer Coefficients ◽  
Enhanced Heat Transfer ◽  
Heat Transfer Coefficients ◽  
Gap Height

This paper presents an experimental study of the heat transfer and pressure drop characteristics of a single phase high heat flux microchannel cooling system with spiraling radial inflow. The heat sink provides enhanced heat transfer with a simple inlet and outlet design while providing uniform flow distribution. The system is heated from one conducting wall made of copper and uses water as a working fluid. The microchannel has a 1 cm radius and a 300 μm gap height. Experimental results show, on average, a 76% larger pressure drop compared to an analytic model for laminar flow in a parallel disk system with spiral radial inflow. The mean heat transfer coefficients measured are up to four times the heat transfer coefficient for unidirectional laminar fully developed flow between parallel plates with the same gap height. Flow visualization studies indicate the presence of secondary flows and the onset of turbulence at higher flow rates. Combined with the thermally developing nature of the flow, these characteristics lead to enhanced heat transfer coefficients relative to the laminar parallel plate values. Another beneficial feature of this device, for high heat flux cooling applications, is that the thermal gradients on the surface are small. The average variation in surface temperature is 18% of the total bulk fluid temperature gain across the device. The system showed promising cooling characteristics for electronics and concentrated photovoltaics applications with a heat flux of 113 W/cm2 at a surface temperature of 77 °C and a ratio of pumping power to heat rate of 0.03%.

Sign in / Sign up

Export Citation Format

Share Document