Impact of Pulse Quenching Effect on Sensitive Area at Advanced Technologies

2013 ◽  
Vol 392 ◽  
pp. 693-696
Author(s):  
Wen Tao Xu ◽  
Yang Guo ◽  
Yan Kang Du
Keyword(s):  
Computer Aided Design ◽  
Three Dimensional ◽  
Sensitive Area ◽  
Isolation Technique ◽  
Quenching Effect ◽  
Advanced Technologies ◽  
Computer Aided ◽  
Simulation Results ◽  
Aided Design ◽  
The Impact

The impact of pulse quenching effect on the sensitive area is evaluated by using three-dimensional technology computer-aided design (TCAD) numerical simulation. Simulation results present that the pulse quenching effect could effectively reduce the sensitive area of PMOS transistors. By adopting the off-state gate isolation technique, the sensitive area is further reduced.

scholarly journals Investigation on the Hump Behavior of Gate-Normal Nanowire Tunnel Field-Effect Transistors (NWTFETs)

2020 ◽  
Vol 10 (24) ◽  
pp. 8880
Author(s):  
Min Woo Kang ◽  
Woo Young Choi
Keyword(s):  
Computer Aided Design ◽  
Field Effect ◽  
Field Effect Transistors ◽  
Three Dimensional ◽  
Gate Insulator ◽  
Radius Of Curvature ◽  
Computer Aided ◽  
Simulation Results ◽  
Tcad Simulation ◽  
Aided Design

The hump behavior of gate-normal nanowire tunnel field-effect transistors (NWTFETs) is investigated by using a three-dimensional technology computer-aided design (TCAD) simulation. The simulation results show that the hump behavior degrades the subthreshold swing (SS) and on-current (Ion) because the corners and sides of nanowires (NWs) have different surface potentials. The hump behavior can be successfully suppressed by increasing the radius of curvature (R) of NWs and reducing gate insulator thickness (Tins).

scholarly journals Automatized Evaluation of Students’ CAD Models

2021 ◽  
Vol 11 (4) ◽  
pp. 145
Author(s):  
Nenad Bojcetic ◽  
Filip Valjak ◽  
Dragan Zezelj ◽  
Tomislav Martinec
Keyword(s):  
Computer Aided Design ◽  
Three Dimensional ◽  
Computer Application ◽  
Test Cases ◽  
Cad Model ◽  
Computer Solution ◽  
3D Cad ◽  
Computer Aided ◽  
Cad Models ◽  
Aided Design

The article describes an attempt to address the automatized evaluation of student three-dimensional (3D) computer-aided design (CAD) models. The driving idea was conceptualized under the restraints of the COVID pandemic, driven by the problem of evaluating a large number of student 3D CAD models. The described computer solution can be implemented using any CAD computer application that supports customization. Test cases showed that the proposed solution was valid and could be used to evaluate many students’ 3D CAD models. The computer solution can also be used to help students to better understand how to create a 3D CAD model, thereby complying with the requirements of particular teachers.

Determination of the Workspace of a Three-Degrees-of-Freedom Parallel Manipulator Using a Three-Dimensional Computer-Aided-Design Software Package and the Concept of Virtual Chains1

2015 ◽  
Vol 8 (2) ◽  
Author(s):  
Andrew Johnson ◽  
Xianwen Kong ◽  
James Ritchie
Keyword(s):  
Computer Aided Design ◽  
Parallel Manipulator ◽  
Degrees Of Freedom ◽  
Graphical Representation ◽  
Three Dimensional ◽  
Parallel Manipulators ◽  
Workspace Analysis ◽  
Computer Aided ◽  
Aided Design

The determination of workspace is an essential step in the development of parallel manipulators. By extending the virtual-chain (VC) approach to the type synthesis of parallel manipulators, this technical brief proposes a VC approach to the workspace analysis of parallel manipulators. This method is first outlined before being illustrated by the production of a three-dimensional (3D) computer-aided-design (CAD) model of a 3-RPS parallel manipulator and evaluating it for the workspace of the manipulator. Here, R, P and S denote revolute, prismatic and spherical joints respectively. The VC represents the motion capability of moving platform of a manipulator and is shown to be very useful in the production of a graphical representation of the workspace. Using this approach, the link interferences and certain transmission indices can be easily taken into consideration in determining the workspace of a parallel manipulator.

scholarly journals Development of integrated intelligent computer-aided design system for mechanical power-transmitting mechanism design

2017 ◽  
Vol 9 (7) ◽  
pp. 168781401771038 ◽  
Author(s):  
Isad Saric ◽  
Adil Muminovic ◽  
Mirsad Colic ◽  
Senad Rahimic
Keyword(s):  
Rapid Prototyping ◽  
Computer Aided Design ◽  
Three Dimensional ◽  
Computer Numerical Control ◽  
Numerical Control ◽  
Mechanical Power ◽  
Design System ◽  
Computer Aided ◽  
Aided Design ◽  
Intelligent Computer

This article presents architecture of integrated intelligent computer-aided design system for designing mechanical power-transmitting mechanisms (IICADkmps). The system has been developed in C# program environment with the aim of automatising the design process. This article presents a modern, automated approach to design. Developed kmps modules for calculation of geometrical and design characteristics of mechanical power-transmitting mechanisms are described. Three-dimensional geometrical parameter modelling of mechanical power-transmitting mechanisms was performed in the computer-aided design/computer-aided manufacturing/computer-aided engineering system CATIA V5. The connection between kmps calculation modules and CATIA V5 modelling system was established through initial three-dimensional models – templates. The outputs from the developed IICADkmps system generated final three-dimensional virtual models of mechanical power-transmitting mechanisms. Testing of the developed IICADkmps system was performed on friction, belt, cogged (spur and bevel gears) and chain transmitting mechanisms. Also, connection of the developed IICADkmps system with a device for rapid prototyping and computer numerical control machines was made for the purpose of additional testing and verification of practical use. Physical prototypes of designed characteristic elements of mechanical power-transmitting mechanisms were manufactured. The selected test three-dimensional virtual prototypes, obtained as an output from the developed IICADkmps system, were manufactured on the device for rapid prototyping (three-dimensional colour printer Spectrum Z510) and computer numerical control machines. Finally, at the end of the article, conclusions and suggested possible directions of further research, based on theoretical and practical research results, are presented.

Recognising Facial Surfaces

Perception ◽  
1991 ◽  
Vol 20 (6) ◽  
pp. 755-769 ◽  
Author(s):  
Vicki Bruce ◽  
Patrick Healey ◽  
Mike Burton ◽  
Tony Doyle ◽  
Anne Coombes ◽  
...  
Keyword(s):  
Computer Aided Design ◽  
Three Dimensional ◽  
Head Model ◽  
Matching Accuracy ◽  
The People ◽  
Computer Aided ◽  
Closed Head ◽  
The Face ◽  
Aided Design ◽  
Dimensional Surface

The extent to which faces depicted as surfaces devoid of pigmentation and with minimal texture cues (‘head models’) could be matched with photographs (when unfamiliar) and identified (when familiar) was examined in three experiments. The head models were obtained by scanning the three-dimensional surface of the face with a laser, and by displaying the surface measured in this way by using standard computer-aided design techniques. Performance in all tasks was above chance but far from ceiling. Experiment 1 showed that matching of unfamiliar head models with photographs was affected by the resolution with which the surface was displayed, suggesting that subjects based their decisions, at least in part, on three-dimensional surface structure. Matching accuracy was also affected by other factors to do with the viewpoints shown in the head models and test photographs, and the type of lighting used to portray the head model. In experiment 2 further evidence for the importance of the nature of the illumination used was obtained, and it was found that the addition of a hairstyle (not that of the target face) did not facilitate matching. In experiment 3 identification of the head models by colleagues of the people shown was compared with identification of photographs where the hair was concealed and eyes were closed. Head models were identified less well than these photographs, suggesting that the difficulties in their recognition are not solely due to the lack of hair. Women's heads were disproportionately difficult to recognise from the head models. The results are discussed in terms of their implications for the use of such three-dimensional head models in forensic and surgical applications.

Effect of In-office Bleaching on Color, Translucency, and Whiteness Variations in CAD-CAM Monolithic Materials

2021 ◽  
Author(s):  
RG Fonseca ◽  
RC Peńa ◽  
R Simóes ◽  
AC Ramos ◽  
LN Dovigo
Keyword(s):  
Optical Properties ◽  
Computer Aided Design ◽  
Calculated Data ◽  
Color Difference ◽  
Deionized Water ◽  
Stain Removal ◽  
Computer Aided ◽  
Cad Cam ◽  
Aided Design ◽  
The Impact

SUMMARY Little is known about the impact of bleaching on the optical properties of computer-aided design and computer-aided manufactured (CAD-CAM) monolithic materials. The aim of the present study was to evaluate the effect of one session of in-office bleaching on stain removal, staining susceptibility, translucency, and whiteness variations of CADCAM monolithic materials. Disks were fabricated from Lava Ultimate (LU), Vita Enamic (VE), Vita Suprinity (VS), and IPS e.max CAD (IPS). A spectrophotometer was used to register Commission Internationale de l’Eclairage L*a*b* coordinates. For stain removal, 80 specimens from each material were assessed at baseline (R0) and after immersion in deionized water or coffee for 365 days followed or not by bleaching with 40% hydrogen peroxide (R1). For staining susceptibility, 80 specimens from each material were analyzed at baseline (R0’), and after having been bleached or not and immersed in deionized water or coffee (R1’). Both analyses were calculated as the color difference (ΔE00) between R1-R0 and R1’-R0’, respectively. Differences in translucency (ΔTP00) and whiteness (ΔWID) between R1-R0 and R1’-R0’ were also calculated. Data were analyzed by three-way ANOVA and the Games-Howell post hoc test (α=0.05). Clinical significance was based on 50%:50% perceptibility and acceptability thresholds for ΔE00, ΔTP00 and ΔWID, respectively. Surfaces were analyzed by scanning electron microscopy. Coffee increased ΔE00 in LU, VE, and VS, and decreased their translucency and whiteness, whereas the IPS had only its whiteness affected. Bleaching after immersion in coffee decreased ΔE00 in LU and VE, and increased translucency and whiteness of LU, VE, and VS. No effect was observed on IPS. Bleaching before immersion in coffee decreased translucency of LU, but within the acceptable interval, while VE exhibited lower ΔE00, and became more translucent and less dark. Both VS and IPS were not affected. One session of in-office bleaching benefited optical properties of the previously stained LU, VE, and VS, without increasing their susceptibility to staining or adversely providing clinically unacceptable variations in their translucency and whiteness. All variations exhibited by the IPS were below the perceptible threshold.

Sign in / Sign up

Export Citation Format

Share Document