Influence of CaO-Based Expansive Agent on the Deformation Behavior of High Performance Concrete

2013 ◽  
Vol 438-439 ◽  
pp. 113-116
Author(s):  
Shou Zhi Zhang ◽  
Qian Tian ◽  
An Qun Lu
Keyword(s):  
Deformation Behavior ◽  
High Performance ◽  
High Performance Concrete ◽  
Control Volume ◽  
Autogenous Shrinkage ◽  
Drying Shrinkage ◽  
Volume Stability ◽  
Expansive Agent ◽  
Effective Expansion ◽  
New Type

In order to improve the volume stability of high performance concrete, the effects of deformation behavior of high performance concrete containing CaO-based expansive agent were investigated. Concrete samples prepared without or with CaO-based expansive agent were compared through expansion under water curing at 20°C, drying shrinkage and autogenous shrinkage measurements. According to the experimental and analytical results, the new type expansive agent can control volume stability for high performance concrete. The addition of 10% CaO-based expansive agent not only built effective expansion in high performance concrete whatever under saturated condition or under sealed condition, but also substantially reduced its drying shrinkage.

Shrinkage Properties of Cement-Silica Fume Blended Pastes in Early Age

2017 ◽  
Vol 726 ◽  
pp. 521-526
Author(s):  
Di Zou ◽  
Lian Zhen Xiao ◽  
Wen Chong Shi
Keyword(s):  
Silica Fume ◽  
Rapid Growth ◽  
High Performance ◽  
High Performance Concrete ◽  
Autogenous Shrinkage ◽  
Drying Shrinkage ◽  
Early Age ◽  
Shrinkage Ratio ◽  
Study Results ◽  
Expansion Period

The cement-silica fume blended pastes were prepared with different silica fume (SF) dosages of 0%, 5%, 10%, and 15% at different water-binder ratios (W/B) of 0.4 and 0.5. The autogenous shrinkage (AS) and the drying shrinkage (DS) of the paste samples in the hydration period of 7d (168 hours) were measured by a new measurement technique to explore the influence of W/B and silica fume incorporation on the shrinkage in early age. The study results can provide reference for high performance concrete mix design.It is found that ether the AS or the DS of the paste samples shows a similar pattern, and the AS development with hydration time appeared a temporary expansion period after a rapid growth, especially in the samples at a higher W/B or with a lower SF content. However, the DS development did not occur obvious expansion period.Three development trends were obtained for the factors of W/B and SF content. 1) the AS and DS of the pastes mainly occurred in early ages. The lower W/B, the shorter the rapid growth periods, and the higher the shrinkage ratio of 1d to 7d. For the pastes with W/B of 0.4, the AS grew rapidly in 1d and the DS grew rapidly in the first 10h, and the AS value in 1d reached to 63.6% of 7d, and the DS value reached to 62.1% of 7d in the paste with SF of 10%. For the pastes with W/B of 0.5, the rapid growth periods of the AS and DS respectively extended to 30~33h and 12h, and the AS value in 1d reached to 60.0% of 7d, and the DS value reached to 57.2% of 7d in the paste with SF of 10%. 2) The lower W/B, the higher the shrinkage ratio of the AS to the DS. When the SF dosage is 10%, the ratio of the AS value to the DS value of 7d is 21.66%~21.15% for W/B of 0.4, and only 6.06%~5.78% for the W/B of 0.5. 3) the higher SF content results in the higher AS in cement-SF blended pastes. For the pastes with W/B of 0.4, the ratio of the AS to the DS increased from 6.98% to 30.16% with the increase of content of SF from 5% to 15% in 1d, from 15.1% to 28.19% in 3d, from 16.78% to 26.16% in 7d.

Chemical Shrinkage of Pastes Made with Shrinkage Reducing Admixtures

2011 ◽  
Vol 466 ◽  
pp. 105-113 ◽  
Author(s):  
António Bettencourt Ribeiro ◽  
Vasco Medina ◽  
Augusto Gomes ◽  
Arlindo Gonçalves
Keyword(s):  
High Performance ◽  
High Performance Concrete ◽  
Autogenous Shrinkage ◽  
Drying Shrinkage ◽  
Chemical Shrinkage ◽  
Cement Pastes ◽  
Degree Of Hydration ◽  
Shrinkage Cracks ◽  
Large Application ◽  
Shrinkage Reducing Admixtures

Shrinkage Reducing Admixtures (SRA) are being used more often in concrete structures in order to better control shrinkage cracks. High-performance concrete, nowadays with large application, has more proneness to crack at very early age due to the lower W/C. In this type of concrete, autogenous shrinkage is usually more important than drying shrinkage. Autogenous shrinkage is due to the volume decrease inherent to binder hydration reactions. The rate of these reactions is influenced not only by the type of binder but also by the presence of chemical admixtures. It is recognized that SRA delay the hydration, being a secondary effect of this type of admixtures. In this work changes on the degree of hydration of cement pastes with SRA and different binders are presented, using the chemical shrinkage test.

Study on the Effect of Different Admixtures on the Early Autogenous Shrinkage of High Performance Concrete of Bridge Deck Pavement

2013 ◽  
Vol 857 ◽  
pp. 56-63 ◽  
Author(s):  
Xiang Qian Li ◽  
Bo Tian ◽  
Wei Liu ◽  
She Su
Keyword(s):  
Fly Ash ◽  
High Performance ◽  
Bridge Deck ◽  
High Performance Concrete ◽  
Autogenous Shrinkage ◽  
Reducing Agent ◽  
Inhibition Mechanism ◽  
Expansive Agent ◽  
Bridge Deck Pavement ◽  
Shrinkage Reducing Agent

This paper analyzed the mechanism of early autogenous shrinkage of concrete, and studied the influence of early autogenous shrinkage of high performance concrete-(HPC) admixed with different kinds of materials of bridge deck pavement. Four different concrete mixes were used: fiber, fiber plus expansive agent, fiber plus fly ash and fiber plus shrinkage-reducing agent. The result shows that the four different mixes can inhibit the autogenous shrinkage of HPC to a certain extent, the inhibitory effect of different mixes in the order of strong to weak is: fiber plus shrinkage-reducing agent, fiber plus fly ash, fiber plus expansive agent, and fiber itself. Furthermore, the inhibition mechanism of each mix was analyzed and a conclusion of mixture of fiber plus fly ash to be the best choice considered of economic and working performance is drawn as well.

scholarly journals Evaluation of the Thermal and Shrinkage Stresses in Restrained High-Performance Concrete

Materials ◽  
2019 ◽  
Vol 12 (22) ◽  
pp. 3680 ◽  
Author(s):  
Yang Yang ◽  
Linhao Ma ◽  
Jie Huang ◽  
Chunping Gu ◽  
Zhenjian Xu ◽  
...  
Keyword(s):  
Thermal Stress ◽  
High Performance ◽  
High Performance Concrete ◽  
Autogenous Shrinkage ◽  
Drying Shrinkage ◽  
Shrinkage Stress ◽  
Early Age ◽  
Volume Deformation ◽  
Curing Conditions ◽  
Drying Shrinkage Stress

The early age volume deformation is the main course for the cracking of high-performance concrete (HPC). Hence, the shrinkage behavior and the restrained stress development of HPC under different restraints and curing conditions were experimentally studied in this paper. The method to separate the stress components in the total restraint stress was proposed. The total restrained stress was separated into autogenous shrinkage stress, drying shrinkage stress and thermal stress. The results showed that the developments of the free shrinkage (autogenous shrinkage and drying shrinkage) and the restrained stress were accelerated when the drying began; but the age when the drying began did not significantly influence the long-term shrinkage and restrained stress of HPC; the autogenous shrinkage stress continuously contributed to the development of the total restrained stress in HPC; the drying shrinkage stress developed very rapidly soon after the drying began; and the thermal stress was generated when the temperature dropped. The thermal stress was predominant at the early age, but the contributions of the three stresses to the total restrained stress were almost the same at the age of 56 d in this study.

Shrinkage of Full-Scale Girders Cast with Self-Consolidating Concrete

2010 ◽  
Vol 129-131 ◽  
pp. 381-385
Author(s):  
Jian Long Wu ◽  
Kamal Henri Khayat ◽  
Feng Xing
Keyword(s):  
High Performance ◽  
High Performance Concrete ◽  
Autogenous Shrinkage ◽  
Critical Factor ◽  
Drying Shrinkage ◽  
Cementitious Materials ◽  
Full Scale ◽  
Self Consolidating Concrete ◽  
Binder Type ◽  
Length Changes

Shrinkage can be critical factor for the design of structural members due to the length changes by the time-dependent deformation. In this investigation, two self-consolidating concrete (SCC) and two high-performance concrete (HPC) mixtures with target 56-day compressive strengths of 55 and 69 MPa and having 18-hour release strengths of 34.5 MPa and 43 MPa, respectively, were used to cast four full-scale AASHTO-Type II girders measuring 9.44-m in length. For each strength level, the SCC and HPC mixtures were proportioned with the same water-to-cementitious materials ratio (w/cm) and binder type. The high-range water-reducing admixture (HRWRA) dosage was adjusted to obtain a slump flow of 680 ± 20 mm for the SCC mixtures and a slump of 160 ± 20 mm for the HPC mixtures. The constructability and shrinkage of full-scale girders cast with SCC and HPC mixtures used in precast prestressed girders were investigated and compared. Results of tests on full-scale girders indicated that, SCC placement was successfully carried out by casting the concrete from location at the midspan of the 9.44-m long girders. Both HPC and SCC mixtures developed similar autogenous shrinkage for the mixtures made with the similar w/cm; the two SCC mixtures developed about 20% greater drying shrinkage than the comparable HPC mixtures after 112 days of drying.

Early-Age Autogenous Shrinkage of High-Performance Concrete Columns by Embedded Fiber Bragg-Grating Sensor

2009 ◽  
Vol 419-420 ◽  
pp. 1-4 ◽  
Author(s):  
Ying Wei Yun ◽  
Ii Young Jang ◽  
Seong Kyum Kim ◽  
Seung Min Park
Keyword(s):  
Fiber Bragg Grating ◽  
High Performance ◽  
High Performance Concrete ◽  
Construction Material ◽  
Autogenous Shrinkage ◽  
Strain Sensor ◽  
Bragg Grating ◽  
Early Age ◽  
Long Time ◽  
Sensor Temperature

High-performance concrete (HPC) as a promising construction material has been widely used in infrastructures and high-rise buildings etc. However, its pretty high autogenous shrinkage (AS) especially in its early age becomes one of the key problems endangering long-time durability of HPC structures. This paper carried out the early age AS research of large scaled HPC column specimens by embedded Fiber Bragg-Grating (FBG) strain sensor. Temperature compensation for FBG strain sensor by thermocouple was also attempted in this paper, and the results were reasonable and acceptable comparing with the result compensated by FBG temperature sensor. Reinforcement influence, size effect and temperature effect on HPC AS were also analyzed respectively in this paper.

Autogenous Shrinkage in Plain Cement Mixtures

2008 ◽  
Vol 400-402 ◽  
pp. 137-143 ◽  
Author(s):  
Vinod Rajayogan ◽  
Obada Kayali
Keyword(s):  
Experimental Determination ◽  
High Performance ◽  
High Performance Concrete ◽  
Autogenous Shrinkage ◽  
Basic Mechanism ◽  
Realistic Model ◽  
Test Method ◽  
Ongoing Research ◽  
Cement Mixtures

Determination of a realistic model for the estimation of autogenous shrinkage in plain cement mixtures has been an ongoing research among researchers in high performance concrete. While no standard test method exists for the determination of autogenous shrinkage, various researchers have designed different test methods for measurement of autogenous shrinkage. Current study involved the experimental determination of autogenous shrinkage using the test method developed by O.M.Jensen and co-workers, complimented with non-contact eddy current sensors. Measurements were conducted from as early as 1.5 hours from the time of casting. The samples were placed in a constant temperature chamber and the temperature of the sample was also monitored using a thermocouple. The study was carried out on plain cement mixtures at three water cement ratios of 0.25, 0.32 and 0.38. Measurements were also conducted on simple sealed prismatic samples but these measurements could only be collected after 24 hours of casting. The work is supplemented with CEMHYD3D simulations of the samples at similar water-cement ratios under sealed conditions so as to understand the development of the microstructure of the cement responsible for autogenous shrinkage. While experimental determination of internal relative humidity is quite difficult, data regarding chemical shrinkage, amount of water left and the development of the discontinuous capillary network from the simulations help to understand the determined experimental values of autogenous shrinkage. A detailed explanation on the causes of autogenous shrinkage and the basic mechanism responsible for it has been presented.

Research on the Problems and Countermeasures for Steam Curing of Assembled Composite Wallboard

2014 ◽  
Vol 580-583 ◽  
pp. 2299-2302
Author(s):  
Chun Yi Xu ◽  
Lei Yan ◽  
Chen Li ◽  
Zhi Wei Cao
Keyword(s):  
Field Test ◽  
Production Line ◽  
High Performance ◽  
High Performance Concrete ◽  
Concrete Durability ◽  
Steam Curing ◽  
Volume Stability ◽  
Actual Production

For researching principle and production line state of steam curing of composite wallboard, the art have been conducted through actual investigation and field test. Based on the influence of steam curing on the strength of high performance concrete, durability and volume stability, put forward suggestions of steam curing system; Several problems have been raised for steam curing in the actual production, then some correlative improve measurements are given. Provide the reference for the production and development of the residential part in our country.

Sign in / Sign up

Export Citation Format

Share Document