Effect of Changing the Position of Tool Point on the Moving Platform on the Kinematics of a 3RRR Planar Parallel Manipulator

2014 ◽  
Vol 541-542 ◽  
pp. 792-797
Author(s):  
Roshdy Foaad Abo-Shanab
Keyword(s):  
Parallel Manipulator ◽  
Performance Criteria ◽  
Mobile Platform ◽  
Optimum Location ◽  
End Effector ◽  
Global Indices ◽  
Reachable Workspace ◽  
Planar Parallel Manipulator ◽  
Moving Platform ◽  
Structural Length

This paper discusses the effect of changing the location of the tool point, on the mobile platform, on the kinematics of a planar parallel manipulator. It is shown that changing the position of the end-effector greatly changes the shape and the area of the reachable workspace. Global conditioning index and the structural length index are used as global indices to find the optimum location of the end-effector on the mobile platform of a parallel manipulator. The results show that the performance criteria are varying in opposite directions, the dexterity is decreasing when the workspace area is increasing. Hence, the problem of optimal design becomes a problem of determination an acceptable compromise between the two requirements. The results of the present work show that the position of the end-effector on the mobile platform should be considered while optimizing the performance of a parallel manipulator.

Workspace Representation of Parallel Manipulators Using the Finite Twist Method

1996 ◽  
Author(s):  
H. Singh ◽  
J. S. Dai ◽  
D. R. Kerr
Keyword(s):  
Parallel Manipulator ◽  
Parallel Manipulators ◽  
Image Space ◽  
End Effector ◽  
Unique Position ◽  
Reachable Workspace ◽  
Planar Parallel Manipulator ◽  
Position And Orientation ◽  
The Individual ◽  
Established Technique

Abstract A method has been developed that successfully represents the workspace of a parallel manipulator within a finite twist image space. A point in this space represents a unique position and orientation of the end effector. The method of analysis is based upon the established technique of simplifying the parallel manipulator, by modelling each leg as an independent serial manipulator. The workspace corresponding to each serial manipulator is mapped onto the image space to produce a hyper-volume. The intersection of the individual hyper-volumes represents the workspace of the complete parallel manipulator. Since the hyper-volume corresponds to all possible positions attainable by the end effector, this represents the reachable workspace. Within the reachable workspace there lies subsets of volumes in ⮲3 that correspond to all possible orientations attainable. Such volumes represent the dextrous workspace. Although the method is illustrated by the use of a Stewart platform, it is equally applicable to the general parallel manipulator. The method is demonstrated successfully by the use of a 3 legged, 3-DOF planar parallel manipulator.

scholarly journals Workspace Delineation of Cable-Actuated Parallel Manipulators

2004 ◽  
Author(s):  
Ethan Stump ◽  
Vijay Kumar
Keyword(s):  
Parallel Manipulator ◽  
Parallel Manipulators ◽  
Extensive Literature ◽  
Reachable Workspace ◽  
Planar Parallel Manipulator ◽  
Analytic Expressions

While there is extensive literature available on parallel manipulators in general, there has been much less attention given to cable-driven parallel manipulators. In this paper, we address the problem of analyzing the reachable workspace using the tools of semi-definite programming. We build on earlier work [1, 2] done using similar techniques by deriving limiting conditions that allow us to compute analytic expressions for the boundary of the reachable workspace. We illustrate this computation for a planar parallel manipulator with four actuators.

Dynamic Modeling of a Parallel Manipulator With Three Translational Degrees of Freedom

1998 ◽  
Author(s):  
Richard Stamper ◽  
Lung-Wen Tsai
Keyword(s):  
Parallel Manipulator ◽  
Degrees Of Freedom ◽  
Close Agreement ◽  
Jacobian Matrix ◽  
Parallel Manipulators ◽  
Kinematic Structure ◽  
End Effector ◽  
Moving Platform ◽  
Euler Approach ◽  
Computationally Intensive

Abstract The dynamics of a parallel manipulator with three translational degrees of freedom are considered. Two models are developed to characterize the dynamics of the manipulator. The first is a traditional Lagrangian based model, and is presented to provide a basis of comparison for the second approach. The second model is based on a simplified Newton-Euler formulation. This method takes advantage of the kinematic structure of this type of parallel manipulator that allows the actuators to be mounted directly on the base. Accordingly, the dynamics of the manipulator is dominated by the mass of the moving platform, end-effector, and payload rather than the mass of the actuators. This paper suggests a new method to approach the dynamics of parallel manipulators that takes advantage of this characteristic. Using this method the forces that define the motion of moving platform are mapped to the actuators using the Jacobian matrix, allowing a simplified Newton-Euler approach to be applied. This second method offers the advantage of characterizing the dynamics of the manipulator nearly as well as the Lagrangian approach while being less computationally intensive. A numerical example is presented to illustrate the close agreement between the two models.

Stiffness estimation of a parallel manipulator using image analysis and camera calibration techniques

Robotica ◽  
2012 ◽  
Vol 31 (4) ◽  
pp. 657-667 ◽  
Author(s):  
Abraham Gonzalez-Hernandez ◽  
Eduardo Castillo-Castaneda
Keyword(s):  
Image Analysis ◽  
Camera Calibration ◽  
Parallel Manipulator ◽  
Parallel Robot ◽  
Parallel Robots ◽  
Mobile Platform ◽  
End Effector ◽  
Simple Implementation ◽  
Specific Position ◽  
Calibration Techniques

SUMMARYThis work presents a methodology using image analysis to estimate the experimental stiffness of a parallel robot, Parallix LKF-2040, a 3-degree-of-freedom manipulator. The proposed methodology has a simple implementation and can be applied to different architectures of parallel robots. This methodology uses image analysis and camera calibration techniques to estimate compliant displacements of mobile platform produced by several loads at the end effector level, and calculate stiffness in a specific position of mobile platform. Experimental results are presented for different positions within the workspace.

Kinematic Synthesis of a Spatial 3-RPS Parallel Manipulator

2003 ◽  
Vol 125 (1) ◽  
pp. 92-97 ◽  
Author(s):  
Han Sung Kim ◽  
Lung-Wen Tsai
Keyword(s):  
Parallel Manipulator ◽  
Degrees Of Freedom ◽  
Parallel Manipulators ◽  
Point Of View ◽  
Dimensional Synthesis ◽  
Kinematic Synthesis ◽  
End Effector ◽  
Solution Methods ◽  
Moving Platform ◽  
At Will

This paper presents the design of spatial 3-RPS parallel manipulators from dimensional synthesis point of view. Since a spatial 3-RPS manipulator has only 3 degrees of freedom, its end effector cannot be positioned arbitrarily in space. It is shown that at most six positions and orientations of the moving platform can be prescribed at will and, given six prescribed positions, there are at most ten RPS chains that can be used to construct up to 120 manipulators. Further, solution methods for fewer than six prescribed positions are also described.

scholarly journals Comparison of Planar Parallel Manipulator Architectures Based on a Multi-Objective Design Optimization Approach

2010 ◽  
Author(s):  
Damien Chablat ◽  
Ste´phane Caro ◽  
Raza Ur-Rehman ◽  
Philippe Wenger
Keyword(s):  
Genetic Algorithm ◽  
Design Optimization ◽  
Parallel Manipulator ◽  
Optimization Problem ◽  
Optimization Approach ◽  
Objective Functions ◽  
Multi Objective ◽  
Planar Parallel Manipulator ◽  
Moving Platform ◽  
Pareto Frontiers

This paper deals with the comparison of planar parallel manipulator architectures based on a multi-objective design optimization approach. The manipulator architectures are compared with regard to their mass in motion and their regular workspace size, i.e., the objective functions. The optimization problem is subject to constraints on the manipulator dexterity and stiffness. For a given external wrench, the displacements of the moving platform have to be smaller than given values throughout the obtained maximum regular dexterous workspace. The contributions of the paper are highlighted with the study of 3-PRR, 3-RPR and 3-RRR planar parallel manipulator architectures, which are compared by means of their Pareto frontiers obtained with a genetic algorithm.

Sensitivity Analysis of Planar Parallel Manipulators

2008 ◽  
Author(s):  
Ste´phane Caro ◽  
Nicolas Binaud ◽  
Philippe Wenger
Keyword(s):  
Sensitivity Analysis ◽  
Parallel Manipulator ◽  
Jacobian Matrix ◽  
Parallel Manipulators ◽  
Geometric Parameters ◽  
Sensitivity Coefficients ◽  
Planar Parallel Manipulator ◽  
Moving Platform ◽  
Conditioning Number ◽  
Planar Parallel Manipulators

This paper deals with the sensitivity analysis of planar parallel manipulators. A methodology is introduced to derive the sensitivity coefficients by means of the study of 3-RPR manipulators. As a matter of fact, the sensitivity coefficients of the pose of its moving platform to variations in the geometric parameters are expressed algebraically, the variations being defined both in Polar and Cartesian coordinates. The dexterity of the manipulator is also studied by means of the conditioning number of its normalized kinematic Jacobian matrix. As an illustrative example, the sensitivity of a symmetrical planar parallel manipulator is analyzed in detail. Finally, the accuracy of the manipulator is compared with its dexterity.

scholarly journals Simulation and Optimisation of a Two Degree of Freedom, Planar, Parallel Manipulator

2021 ◽  
Author(s):  
◽  
Ben Haughey
Keyword(s):  
Genetic Algorithm ◽  
Simulation Model ◽  
Cycle Time ◽  
Parallel Manipulator ◽  
Robotic Manipulators ◽  
Degree Of Freedom ◽  
End Effector ◽  
Planar Parallel Manipulator ◽  
Pick And Place ◽  
Two Degree Of Freedom

<p>Development in pick-and-place robotic manipulators continues to grow as factory processes are streamlined. One configuration of these manipulators is the two degree of freedom, planar, parallel manipulator (2DOFPPM). A machine building company, RML Engineering Ltd., wishes to develop custom robotic manipulators that are optimised for individual pick-and-place applications. This thesis develops several tools to assist in the design process. The 2DOFPPM’s structure lends itself to fast and accurate translations in a single plane. However, the performance of the 2DOFPPM is highly dependent on its dimensions. The kinematics of the 2DOFPPM are explored and used to examine the reachable workspace of the manipulator. This method of analysis also gives insight into the relative speed and accuracy of the manipulator’s end-effector in the workspace. A simulation model of the 2DOFPPM has been developed in Matlab’s® SimMechanics®. This allows the detailed analysis of the manipulator’s dynamics. In order to provide meaningful input into the simulation model, a cubic spline trajectory planner is created. The algorithm uses an iterative approach of minimising the time between knots along the path, while ensuring the kinematic and dynamic limits of the motors and end-effector are abided by. The resulting trajectory can be considered near-minimum in terms of its cycle-time. The dimensions of the 2DOFPPM have a large effect on the performance of the manipulator. Four major dimensions are analysed to see the effect each has on the cycle-time over a standardised path. The dimensions are the proximal and distal arms, spacing of the motors and the height of the manipulator above the workspace. The solution space of all feasible combinations of these dimensions is produced revealing cycle-times with a large degree of variation over the same path. Several optimisation algorithms are applied to finding the manipulator configuration with the fastest cycle-time. A random restart hill-climber, stochastic hill-climber, simulated annealing and a genetic algorithm are developed. After each algorithm’s parameters are tuned, the genetic algorithm is shown to outperform the other techniques.</p>

Dynamics of a Flexible-Link Planar Parallel Manipulator in Cartesian Space

1994 ◽  
Author(s):  
Abbas Fattah ◽  
Arun K. Misra ◽  
Jorge Angeles
Keyword(s):  
Parallel Manipulator ◽  
High Speed ◽  
Inverse Dynamics ◽  
Equations Of Motion ◽  
Flexible Link ◽  
End Effector ◽  
Joint Torques ◽  
Flexible Links ◽  
Cartesian Space ◽  
Planar Parallel Manipulator

Abstract The subject of this paper is the modeling and simulation of a flexible-link planar parallel manipulator in Cartesian space. Given a desired end-effector motion, the inverse kinematics and inverse dynamics of a rigid-link model of the parallel manipulator is used to obtain actuated joint torques. The actual end-effector motion and vibration of the flexible links are obtained using simulation (direct dynamics) for the flexible-link manipulator. Finite elements are used to model the flexible links, while the Euler-Lagrange formulation is used to derive the equations of motion of the uncoupled links. The equations of motion of all the links are assembled to obtain the governing equations for the entire system. The methodology of the natural orthogonal complement, which has been previously applied to flexible-link systems with open-chain structures, is used here to eliminate the constraint forces. Finally, geometric nonlinearities in elastic deformations, which are very important in high-speed operations, are also considered.

Bond Graph Modeling and Simulating of 3 RPR Planar Parallel Manipulator

2014 ◽  
Author(s):  
Cheng Yin ◽  
Shengqi Jian ◽  
Md. Hassan Faghih ◽  
Md. Toufiqul Islam ◽  
Luc Rolland
Keyword(s):  
Parallel Manipulator ◽  
High Speed ◽  
Reference Frames ◽  
Bond Graph ◽  
Dynamics Simulation ◽  
Bond Graphs ◽  
End Effector ◽  
Planar Parallel Manipulator ◽  
Bond Graph Modeling ◽  
Graph System

A 3-RPR planar parallel robot is a kind of planar mechanisms, which can work at high speed, with high accuracy and high rigidity. In this paper, a multi-body bond graph system will be built for the 3-RPR planar parallel manipulator (PPM), along with 3 PID controllers which give commands to 3 DC motors respectively. The advantage of bond graphs is that they can integrate different types of dynamics systems, the manipulator, the control and the motor can be modelled and simulated altogether in the same process. Bond graph will be established for each rigid body with body-fixed coordinate’s reference frames, which are connected with parasitic elements (damping and compliance) to each other. The PID set-point signals are generated by the explicit inverse kinematic equations. The 3 prismatic lengths constitute the measured feedback signals. In order to make the end-effector reach the ideal position with target orientation, the three links should reach the target lengths simultaneously. In this study, the dynamics simulation of 3-RPR PPM is conducted after building the bond graph system. As the 3 motors are working simultaneously and independently, the end-effector will arrive to the expected position. Finally, the bond graph and control system are validated with the compiled results and 3D animation. Force plot and torque plot will be generated as dynamics performance. Moreover, kinematics of manipulators are also calculated using bond graph. Eventually, bond graphs are shown to be effective in solving not only dynamic but also kinematic problems.

Sign in / Sign up

Export Citation Format

Share Document