Tribological Characterization of the Cutting Zone in Milling Nickel Based Alloy

2014 ◽  
Vol 554 ◽  
pp. 12-16 ◽  
Author(s):  
Musfirah Abdul Hadi ◽  
Jaharah A. Ghani ◽  
C.H. Che Haron ◽  
Natasha A. Raof
Keyword(s):  
Surface Roughness ◽  
Physical Vapor Deposition ◽  
Cutting Temperature ◽  
Cryogenic Cooling ◽  
Cutting Condition ◽  
Dry Machining ◽  
Cutting Zone ◽  
Tribological Characterization ◽  
Coated Carbide

In the area of tribology, surface roughness has become one of the most important factors that contributed to the evaluation of part quality during machining operation. In order to understand the behavior of cryogenic cooling assistance in machining Inconel 718, this paper aims to provide better understanding of tribological characterization of liquid nitrogen near the cutting zone of this material in milling process. Experiments were performed using physical vapor deposition (PVD) - coated carbide inserts under cryogenic and dry cutting condition. The cryogenic results of the cutting temperature, cutting forces and surface roughness of the ball nose cutting tool have been compared with those of dry machining. Finally, experimental results proved that cryogenic implementation can decrease the amount of heat transferred to the tool up to almost 70% and improve the surface roughness to a maximum of 31% when compared with dry machining.

EFFECT OF CUTTING PARAMETERS ON CUTTING ZONE IN CRYOGENIC HIGH SPEED MILLING OF INCONEL 718 ALLOY

2015 ◽  
Vol 77 (27) ◽  
Author(s):  
A. H. Musfirah ◽  
J. A. Ghani ◽  
C. H. Che Haron ◽  
M. S. Kasim
Keyword(s):  
Surface Roughness ◽  
Inconel 718 ◽  
End Milling ◽  
Cutting Temperature ◽  
Cryogenic Cooling ◽  
Cutting Condition ◽  
Dry Machining ◽  
Part Quality ◽  
Cutting Zone ◽  
Coated Carbide

In tribology phenomenon, surface roughness has become one of the most important factors that contributed to the evaluation of part quality during machining operation. In order to understand the behavior of cryogenic cooling assistance in machining Inconel 718, this paper aims to provide better understanding of tribological characterization of liquid nitrogen near the cutting zone of this material in ball end milling process. Experiments were performed using a multi-layer TiAlN/AlCrN-coated carbide inserts under cryogenic and dry cutting condition. A transient milling simulation model using Third Wave Advantedge has been done in order to gain in-depth understanding of the thermomechanical aspects of machining and their influence on resulted part quality. The cryogenic results of the cutting temperature, cutting forces and surface roughness of the ball nose cutting tool have been compared with those of dry machining. Finally, experimental results proved that cryogenic implementation can  decrease the amount of heat transferred to the tool up to almost 70% and improve the surface roughness to a maximum of 31% when compared with dry machining. Furthermore, the microstructure of machined workpiece revealed that cryogenic cooling also can reduce a plastic deformation at the cutting surface as compared with the dry machining. 

Monitoring of Cutting Conditions with Dry Cutting on CNC Turning Machine

2010 ◽  
Vol 443 ◽  
pp. 382-387 ◽  
Author(s):  
Somkiat Tangjitsitcharoen ◽  
Suthas Ratanakuakangwan
Keyword(s):  
Surface Roughness ◽  
Tool Wear ◽  
Cutting Forces ◽  
Cutting Temperature ◽  
Cutting Conditions ◽  
Cutting Condition ◽  
Nose Radius ◽  
Dry Cutting ◽  
Cnc Turning ◽  
Coated Carbide

This paper presents the additional work of the previous research in order to verify the previously obtained cutting condition by using the different cutting tool geometries. The effects of the cutting conditions with the dry cutting are monitored to obtain the proper cutting condition for the plain carbon steel with the coated carbide tool based on the consideration of the surface roughness and the tool life. The dynamometer is employed and installed on the turret of CNC turning machine to measure the in-process cutting forces. The in-process cutting forces are used to analyze the cutting temperature, the tool wear and the surface roughness. The experimentally obtained results show that the surface roughness and the tool wear can be well explained by the in-process cutting forces. Referring to the criteria, the experimentally obtained proper cutting condition is the same with the previous research except the rake angle and the tool nose radius.

Effects of Liquid Nitrogen on Cryogenic Machining of Aisi D2 Hardened Steel

2011 ◽  
Vol 335-336 ◽  
pp. 400-405
Author(s):  
Samraj Ravi ◽  
Murugasan Pradeep Kumar
Keyword(s):  
Surface Roughness ◽  
Cutting Force ◽  
Liquid Nitrogen ◽  
Cutting Temperature ◽  
Hardened Steel ◽  
Cryogenic Machining ◽  
Workpiece Surface ◽  
Aisi D2 ◽  
Cutting Zone ◽  
Coated Carbide

The milling of hardened steel generates very high temperature in the cutting zone, and leads to detrimental effects on the cutting force, workpiece surface finish and tool life. Cryogenic machining is an environmental friendly new approach for the desirable control of the cutting temperature in the cutting zone. The present work investigates the effect of cryogenic cooling by liquid nitrogen (LN2) on the cutting temperature, cutting force and workpiece surface roughness on the end milling of AISI D2 steel by CVD TiN coated carbide insert, at a constant cutting speed of 100 m/min and varying feed rate in the range of 0.01-0.02 mm/tooth. The experimental results showed that with LN2 as a coolant the cutting force and workpiece surface roughness were reduced compared to dry and wet machining due to the better lubrication and cooling effect through reduction of cutting zone temperature.

scholarly journals Tool Life and Surface Roughness of A390 Aluminum Alloy in Milling Process Under Dry and Cryogenic Conditions

2018 ◽  
Vol 7 (4.36) ◽  
pp. 432
Author(s):  
K. Othman ◽  
J. A.Ghani ◽  
J. Afifah ◽  
H. A.Rahman ◽  
C. H.Haron ◽  
...  
Keyword(s):  
Surface Roughness ◽  
Aluminum Alloy ◽  
Tool Life ◽  
Weight Ratio ◽  
Cryogenic Cooling ◽  
Depth Of Cut ◽  
Cutting Condition ◽  
Radial Depth ◽  
Coated Carbide ◽  
Cryogenic Conditions

Aluminum alloy is a lightweight material with high strength-to-weight ratio, low thermal expansion, excellent castability and is applied for heavy wear applications. Recent trends in machining research aimed for improving process and product performance by understand the effect of different cooling/lubrication techniques on machining execution. The milling of A390 Al-Si alloy under dry and cryogenic conditions was investigated and liquid nitrogen (LN2) was used as the cryogenic media. The experimental trial were performance with cutting speeds at 250-350 m/min, feed rates at 0.02-0.04 mm/tooth, radial depth of cut at 12.5-25 mm, and the axial depth of cut was kept constant at 0.3 mm using a coated carbide cutting insert. The results outcomes indicate, an application of cryogenic machining had improved the surface roughness, and there was higher tool life as compared to dry cutting condition. The utilization of cryogenic cooling technique had increased the tool life more than 50% and improved the surface roughness more than 40% as compared with dry condition. It is suggested to the machining industry to consider the application of LN2 as the cryogenic media to have better machinability in machining A390 Al-Si alloy.   

Prediction of Surface Roughness on CNC Turning Based on Monitoring of Cutting Force and Cutting Temperature

2013 ◽  
Vol 690-693 ◽  
pp. 2540-2549 ◽  
Author(s):  
Somkiat Tangjitsitcharoen
Keyword(s):  
Surface Roughness ◽  
Cutting Force ◽  
Cutting Temperature ◽  
Experimental Results ◽  
Depth Of Cut ◽  
Cutting Condition ◽  
Cnc Turning ◽  
Roughness Model ◽  
Developed Surface ◽  
Coated Carbide

This paper presents the surface roughness model which is proposed and developed to predict the surface roughness in the CNC turning of the carbon steel with the coated carbide tool under various cutting conditions by using the response surface analysis with the Box-Behnken design based on the experimental results. The in-process monitoring of the cutting force and the cutting temperature is utilized to analyze the relation between the surface roughness and the cutting condition. The tool dynamometer and the infrared pyrometer are employed and installed on the turret of CNC turning machine to measure the in-process cutting force and cutting temperature. The models of cutting force ratio and cutting temperature are also developed based on the experimental data. The optimum cutting condition is determined referring to the minimum surface roughness of the surface plot, which is obtained from the developed surface roughness model. The experimental results show that the higher cutting speed gives the better surface roughness due to the higher cutting temperature, however the tool life becomes shorter. The feed rate is the most significant factor which affects the surface roughness, while a small depth of cut helps to improve the surface roughness. The effectiveness of the surface roughness prediction model has been proved by utilizing an analysis of variance (ANOVA) at 95% confident level. Hence, the surface roughness can be predicted and obtained easily referring to the developed surface roughness model.

Development of Surface Roughness Prediction for Steel in CNC Turning by Using Response Surface Method

2011 ◽  
Vol 335-336 ◽  
pp. 921-926
Author(s):  
Siriwan Chanphong ◽  
Somkiat Tangjitsitcharoen
Keyword(s):  
Surface Roughness ◽  
Cutting Force ◽  
Response Surface ◽  
Cutting Temperature ◽  
Cutting Parameters ◽  
Plain Carbon Steel ◽  
Cutting Condition ◽  
Surface Roughness Prediction ◽  
Roughness Prediction ◽  
Coated Carbide

This research presents the development of the surface roughness prediction in the turning process of the plain carbon steel with the coated carbide tool by using the response surface analysis with the Box-Behnken design. The effects of cutting parameters on the cutting force and the cutting temperature are investigated. The cutting force and the cutting temperature are measured to help analyze the relation between the surface roughness and the cutting conditions. The models of cutting force ratio and the cutting temperature are also proposed based on the experimental data. The surface plots are constructed to determine the optimum cutting condition referring to the minimum surface roughness.

Cryogenic Machining of Titanium Ti-5553 Alloy

2019 ◽  
Vol 141 (4) ◽  
Author(s):  
Yusuf Kaynak ◽  
Armin Gharibi
Keyword(s):  
Titanium Alloy ◽  
Tool Wear ◽  
Cutting Temperature ◽  
Cryogenic Cooling ◽  
Machining Process ◽  
Dry Machining ◽  
Cryogenic Machining ◽  
Machining Performance ◽  
Wide Range ◽  
New Generation

Titanium alloy Ti-5Al-5V-3Cr-0.5Fe (Ti-5553) is a new generation of near-beta titanium alloy that is commonly used in the aerospace industry. Machining is one of the manufacturing methods to produce parts that are made of this near-beta alloy. This study presents the machining performance of new generation near-beta alloys, namely, Ti-5553, by focusing on a high-speed cutting process under cryogenic cooling conditions and dry machining. The machining experiments were conducted under a wide range of cutting speeds, including high speeds that used liquid nitrogen (LN2) and carbon dioxide (CO2) as cryogenic coolants. The experimental data on the cutting temperature, tool wear, force components, chip breakability, dimensional accuracy, and surface integrity characteristics are presented and were analyzed to evaluate the machining process of this alloy and resulting surface characteristics. This study shows that cryogenic machining improved the machining performance of the Ti-5553 alloy by substantially reducing the tool wear, cutting temperature, and dimensional deviation of the machined parts. The cryogenic machining also produced shorter chips as compared to dry machining.

Experimental Study on Turning of Alloy Cast Iron with Coated and Uncoated Tools

2010 ◽  
Vol 135 ◽  
pp. 265-270 ◽  
Author(s):  
Q.C. Wang ◽  
Qing Long An ◽  
Ming Chen ◽  
Gang Liu ◽  
Yun Shan Zhang
Keyword(s):  
Surface Roughness ◽  
Cast Iron ◽  
Tool Wear ◽  
Great Influence ◽  
Cutting Condition ◽  
Dry Cutting ◽  
Coated Tool ◽  
Coated Carbide ◽  
Alloy Cast Iron ◽  
Alloy Cast

Alloy cast iron cylinder is the mainstream product used in engine nowadays. However, the machinability of alloy cast iron is poor because of its enhanced mechanical properties. In this paper, turning experiment has been conducted to study machinability of alloy cast iron with uncoated and coated carbide tools under dry cutting condition. The results of the experiment indicated that the turning performance of alloy cast iron with coated tool was much better than uncoated tool in terms of cutting force coefficients and tool wear. Feed rate has a great influence on surface roughness, and appropriate tool wear is benefit of finished surface roughness.

Machining characteristics of Inconel 718 under several cutting conditions based on Taguchi method

2012 ◽  
Vol 227 (9) ◽  
pp. 1889-1897 ◽  
Author(s):  
R Thirumalai ◽  
JS Senthilkumaar ◽  
P Selvarani ◽  
S Ramesh
Keyword(s):  
Surface Roughness ◽  
Inconel 718 ◽  
Flank Wear ◽  
Optimization Technique ◽  
Cutting Speed ◽  
Depth Of Cut ◽  
Cutting Condition ◽  
Machining Parameters ◽  
Dry Machining ◽  
Noise Factors

Extensive researchers have conducted several experiments in the past for selecting the optimum parameters in machining nickel based alloy – Inconel 718. These experiments conducted so far are dealt with dry machining and flooded coolant machining of nickel alloy Inconel 718. In this research study, the usage of refrigerated coolant is also dealt with and it is compared with dry machining and flooded coolant machining. Cutting speed, feed and depth of cut are considered as the machining parameters. The effectiveness of the refrigerated coolant in machining the heat resistant super alloy material Inconel 718 with respect to these machining parameters are described in this article. The machinability studies parameters were generated with surface roughness and flank wear. The performance of uncoated carbide cutting tool was investigated at various cutting condition under dry, flooded coolant and refrigerated coolant machining. The relationship between the machining parameters and the performance measures were established and using analysis of variance significant machining parameters determined. This article made an attempt to Taguchi optimization technique to study the machinability performances of Inconel 718. Taguchi approach is an efficient and effective experimental method in which a response variable can be optimized, given various control and noise factors, using fewer experiments than a factorial design. Taguchi’s optimization analysis indicates that the factors level, its significance to influence the surface roughness and flank wear for the machining processes. Confirmation tests were conducted at an optimal condition to make a comparison between the experimental results foreseen from the mentioned correlations.

A Study of Surface Integrity when Machining Refractory Titanium Alloys

2009 ◽  
Vol 83-86 ◽  
pp. 1059-1068 ◽  
Author(s):  
Armansyah Ginting ◽  
Mohammed Nouari ◽  
Nadhir Lebaal
Keyword(s):  
Surface Roughness ◽  
Titanium Alloys ◽  
Surface Integrity ◽  
Bulk Material ◽  
Cutting Speed ◽  
Cutting Condition ◽  
Feed Speed ◽  
Machined Surface ◽  
Feed Mark ◽  
Coated Carbide

In this paper, the surface integrity is studied when machining the aeronautical titanium alloys. Surface roughness, lay, defects, microhardness and microstructure alterations are studied. The result of surface roughness judges that the CVD-coated carbide fails to produce better Ra value than the uncoated. Lay is characterized by cutting speed and feed speed directions. Feed mark, tearing surface, chip layer formation as built up layer (BUL), and deposited microchip are the defects. Microhardness is altered down to 350 microns beneath the machined surface. The first 50 microns is the soft sub-surface caused by thermal softening in ageing process. Microstructure alteration is observed in this sub-surface. Down to 200 microns is the hard sub-surface caused by the cyclic internal work hardening and then it is gradually decreasing to the bulk material hardness. It is concluded that dry machining titanium alloy is possible using uncoated carbide with cutting condition limited to finish or semi-finish for minimizing surface integrity alteration.

Sign in / Sign up

Export Citation Format

Share Document