scholarly journals Tool Life and Surface Roughness of A390 Aluminum Alloy in Milling Process Under Dry and Cryogenic Conditions

2018 ◽  
Vol 7 (4.36) ◽  
pp. 432
Author(s):  
K. Othman ◽  
J. A.Ghani ◽  
J. Afifah ◽  
H. A.Rahman ◽  
C. H.Haron ◽  
...  
Keyword(s):  
Surface Roughness ◽  
Aluminum Alloy ◽  
Tool Life ◽  
Weight Ratio ◽  
Cryogenic Cooling ◽  
Depth Of Cut ◽  
Cutting Condition ◽  
Radial Depth ◽  
Coated Carbide ◽  
Cryogenic Conditions

Aluminum alloy is a lightweight material with high strength-to-weight ratio, low thermal expansion, excellent castability and is applied for heavy wear applications. Recent trends in machining research aimed for improving process and product performance by understand the effect of different cooling/lubrication techniques on machining execution. The milling of A390 Al-Si alloy under dry and cryogenic conditions was investigated and liquid nitrogen (LN2) was used as the cryogenic media. The experimental trial were performance with cutting speeds at 250-350 m/min, feed rates at 0.02-0.04 mm/tooth, radial depth of cut at 12.5-25 mm, and the axial depth of cut was kept constant at 0.3 mm using a coated carbide cutting insert. The results outcomes indicate, an application of cryogenic machining had improved the surface roughness, and there was higher tool life as compared to dry cutting condition. The utilization of cryogenic cooling technique had increased the tool life more than 50% and improved the surface roughness more than 40% as compared with dry condition. It is suggested to the machining industry to consider the application of LN2 as the cryogenic media to have better machinability in machining A390 Al-Si alloy.   

Effect of Tool Wear on Tri-Phase CVD Coated Carbide Tools Life while Turning Al6061

2012 ◽  
Vol 488-489 ◽  
pp. 457-461 ◽  
Author(s):  
Ali Davoudinejad ◽  
Sina Alizadeh Ashrafi ◽  
Abdolkarim Niazi
Keyword(s):  
Surface Roughness ◽  
Tool Wear ◽  
Tool Life ◽  
Wear Mechanisms ◽  
Orthogonal Cutting ◽  
Depth Of Cut ◽  
Cutting Condition ◽  
Tool Edge ◽  
Product Surface ◽  
Coated Carbide

Aluminum 6061 is a common alloy which is widely used in aerospace and yacht construction industry. Generally machining of aluminum alloys inherently generates high chip sticking on tool face and changes the tool edge geometry, which not only reduces tool life but also impairs the product surface quality. This study investigated the tool life and tool wear mechanisms besides evaluating surface roughness in various cutting conditions to attain finest possible surface with minimum tool wear. Turning experiments performed under dry orthogonal cutting of Al6061 using carbide CVD tri-phase coated inserts with constant depth of cut, various cutting speeds and feed rates. Insert’s flank and rake faces analyzed to assess wear mechanisms. Additionally Scanning electron microscope (SEM) employed to clarify different types of wear. Surface integrity and effect of built up edge in deviating surface roughness were studied in each cutting condition. Additionally results of experiments demonstrated that built up edge took over cutting edge and with sacrificing surface roughness, tool life increased by decreasing pace of abrasive wear propagation on flank face. According to these experiments the main reasons of flank wear were abrasive and adhesion of aluminum on tool face.

A Comprehensive Study on Surface Roughness in Machining of AISI D2 Hardened Steel

2012 ◽  
Vol 576 ◽  
pp. 60-63 ◽  
Author(s):  
N.A.H. Jasni ◽  
Mohd Amri Lajis
Keyword(s):  
Surface Roughness ◽  
High Speed ◽  
End Milling ◽  
Cutting Speed ◽  
Hardened Steel ◽  
Depth Of Cut ◽  
Feed Speed ◽  
Radial Depth ◽  
Aisi D2 ◽  
Coated Carbide

Hard milling of hardened steel has wide application in mould and die industries. However, milling induced surface finish has received little attention. An experimental investigation is conducted to comprehensively characterize the surface roughness of AISI D2 hardened steel (58-62 HRC) in end milling operation using TiAlN/AlCrN multilayer coated carbide. Surface roughness (Ra) was examined at different cutting speed (v) and radial depth of cut (dr) while the measurement was taken in feed speed, Vf and cutting speed, Vc directions. The experimental results show that the milled surface is anisotropic in nature. Surface roughness values in feed speed direction do not appear to correspond to any definite pattern in relation to cutting speed, while it increases with radial depth-of-cut within the range 0.13-0.24 µm. In cutting speed direction, surface roughness value decreases in the high speed range, while it increases in the high radial depth of cut. Radial depth of cut is the most influencing parameter in surface roughness followed by cutting speed.

EFFECT OF CUTTING PARAMETERS ON CUTTING ZONE IN CRYOGENIC HIGH SPEED MILLING OF INCONEL 718 ALLOY

2015 ◽  
Vol 77 (27) ◽  
Author(s):  
A. H. Musfirah ◽  
J. A. Ghani ◽  
C. H. Che Haron ◽  
M. S. Kasim
Keyword(s):  
Surface Roughness ◽  
Inconel 718 ◽  
End Milling ◽  
Cutting Temperature ◽  
Cryogenic Cooling ◽  
Cutting Condition ◽  
Dry Machining ◽  
Part Quality ◽  
Cutting Zone ◽  
Coated Carbide

In tribology phenomenon, surface roughness has become one of the most important factors that contributed to the evaluation of part quality during machining operation. In order to understand the behavior of cryogenic cooling assistance in machining Inconel 718, this paper aims to provide better understanding of tribological characterization of liquid nitrogen near the cutting zone of this material in ball end milling process. Experiments were performed using a multi-layer TiAlN/AlCrN-coated carbide inserts under cryogenic and dry cutting condition. A transient milling simulation model using Third Wave Advantedge has been done in order to gain in-depth understanding of the thermomechanical aspects of machining and their influence on resulted part quality. The cryogenic results of the cutting temperature, cutting forces and surface roughness of the ball nose cutting tool have been compared with those of dry machining. Finally, experimental results proved that cryogenic implementation can  decrease the amount of heat transferred to the tool up to almost 70% and improve the surface roughness to a maximum of 31% when compared with dry machining. Furthermore, the microstructure of machined workpiece revealed that cryogenic cooling also can reduce a plastic deformation at the cutting surface as compared with the dry machining. 

Cutting Forces and Surface Roughness in High-Speed End Milling of Ti6Al4V

2013 ◽  
Vol 589-590 ◽  
pp. 76-81
Author(s):  
Fu Zeng Wang ◽  
Jun Zhao ◽  
An Hai Li ◽  
Jia Bang Zhao
Keyword(s):  
Surface Roughness ◽  
Surface Quality ◽  
Cutting Forces ◽  
High Speed ◽  
End Milling ◽  
Cutting Speed ◽  
Depth Of Cut ◽  
Wide Range ◽  
Radial Depth ◽  
Coated Carbide

In this paper, high speed milling experiments on Ti6Al4V were conducted with coated carbide inserts under a wide range of cutting conditions. The effects of cutting speed, feed rate and radial depth of cut on the cutting forces, chip morphologies as well as surface roughness were investigated. The results indicated that the cutting speed 200m/min could be considered as a critical value at which both relatively low cutting forces and good surface quality can be obtained at the same time. When the cutting speed exceeds 200m/min, the cutting forces increase rapidly and the surface quality degrades. There exist obvious correlations between cutting forces and surface roughness.

scholarly journals OPTIMUM PERFORMANCE OF GREEN MACHINING ON THIN WALLED TI6AL4V USING RSM AND ANN IN TERMS OF CUTTING FORCE AND SURFACE ROUGHNESS

2019 ◽  
Vol 81 (6) ◽  
Author(s):  
Muhammad Yanis ◽  
Amrifan Saladin Mohruni ◽  
Safian Sharif ◽  
Irsyadi Yani
Keyword(s):  
Surface Roughness ◽  
Cutting Force ◽  
Cutting Speed ◽  
Weight Ratio ◽  
Cutting Fluid ◽  
Depth Of Cut ◽  
Ann Model ◽  
Green Machining ◽  
Radial Depth ◽  
Thin Walled

Thin walled titanium alloys are mostly applied in the aerospace industry owing to their favorable characteristic such as high strength-to-weight ratio. Besides vibration, the friction at the cutting zone in milling of thin-walled Ti6Al4V will create inconsistencies in the cutting force and increase the surface roughness. Previous researchers reported the use of vegetable oils in machining metal as an effort towards green machining in reducing the undesirable cutting friction. Machining experiments were conducted under Minimum Quantity Lubrication (MQL) using coconut oil as cutting fluid, which has better oxidative stability than other vegetable oil. Uncoated carbide tools were used in this milling experiment. The influence of cutting speed, feed and depth of cut on cutting force and surface roughness were modeled using response surface methodology (RSM) and artificial neural network (ANN). Experimental machining results indicated that ANN model prediction was more accurate compared to the RSM model. The maximum cutting force and surface roughness values recorded are 14.89 N, and 0.161 µm under machining conditions of 125 m/min cutting speed, 0.04 mm/tooth feed, 0.25 mm radial depth of cut (DOC) and 5 mm axial DOC. 

Optimal Cutting Parameters for Desired Surface Roughness in End Milling Inconel 718

2010 ◽  
Vol 126-128 ◽  
pp. 911-916 ◽  
Author(s):  
Yuan Wei Wang ◽  
Song Zhang ◽  
Jian Feng Li ◽  
Tong Chao Ding
Keyword(s):  
Surface Roughness ◽  
Inconel 718 ◽  
End Milling ◽  
Cutting Speed ◽  
Cutting Parameters ◽  
Depth Of Cut ◽  
Radial Depth ◽  
Exponential Regression Model ◽  
Optimal Cutting Parameters ◽  
Coated Carbide

In this paper, Taguchi method was applied to design the cutting experiments when end milling Inconel 718 with the TiAlN-TiN coated carbide inserts. The signal-to-noise (S/N) ratio are employed to study the effects of cutting parameters (cutting speed, feed per tooth, radial depth of cut, and axial depth of cut) on surface roughness, and the optimal combination of the cutting parameters for the desired surface roughness is obtained. An exponential regression model for the surface roughness is formulated based on the experimental results. Finally, the verification tests show that surface roughness generated by the optimal cutting parameters is really the minimum value, and there is a good agreement between the predictive results and experimental measurements.

Evaluation and investigation of grinding process of biomedical polymer (PEEK)

2021 ◽  
pp. 095440892110225
Author(s):  
Mohammad Khoran ◽  
Bahman Azarhoushang ◽  
Hossein Amirabadi
Keyword(s):  
Surface Roughness ◽  
Cutting Speed ◽  
Weight Ratio ◽  
Speed Ratio ◽  
Depth Of Cut ◽  
Grinding Wheel ◽  
Cutting Condition ◽  
Grinding Process ◽  
Wheel Topography ◽  
Overlap Ratio

Polyether ether ketone (PEEK) has been widely used in the medical engineering due to its high strength to weight ratio, creep and wear-resistance, and anti-allergically properties. Grinding is generally used to produce PEEK parts with high accuracy and surface quality requirements. In this research, the tool loading and the effect of cryogenic cooling in the grinding of PEEK are studied for the first time. It is shown that the generated heat in the grinding process, which is mainly influenced by the tool micro-topography, process parameter, and coolant lubricant has an important role in the surface integrity of PEEK. Additionally, the influence of specific material removal rate and the dressing speed ratio on the specific grinding energy of PEEK was studied. The input parameters of the grinding process that are investigated in this study include cutting speed (vs), depth of cut (ae), and feed rate (vft). To investigate the grinding wheel topography, the effects of dressing overlap ratio (Ud) and the dressing speed ratio (qd) were also investigated. Grinding force, surface roughness, and loading of the grinding wheel were considered as output parameters. The experiments were designed based on response surface methodology and the optimum cutting condition was obtained based on this method. The depth of cut and the dressing overlap ratio had respectively the maximum and minimum impact on the surface roughness and cutting forces. Additionally, the tool loading was mainly influenced by the cutting speed.

Tribological Characterization of the Cutting Zone in Milling Nickel Based Alloy

2014 ◽  
Vol 554 ◽  
pp. 12-16 ◽  
Author(s):  
Musfirah Abdul Hadi ◽  
Jaharah A. Ghani ◽  
C.H. Che Haron ◽  
Natasha A. Raof
Keyword(s):  
Surface Roughness ◽  
Physical Vapor Deposition ◽  
Cutting Temperature ◽  
Cryogenic Cooling ◽  
Cutting Condition ◽  
Dry Machining ◽  
Cutting Zone ◽  
Tribological Characterization ◽  
Coated Carbide

In the area of tribology, surface roughness has become one of the most important factors that contributed to the evaluation of part quality during machining operation. In order to understand the behavior of cryogenic cooling assistance in machining Inconel 718, this paper aims to provide better understanding of tribological characterization of liquid nitrogen near the cutting zone of this material in milling process. Experiments were performed using physical vapor deposition (PVD) - coated carbide inserts under cryogenic and dry cutting condition. The cryogenic results of the cutting temperature, cutting forces and surface roughness of the ball nose cutting tool have been compared with those of dry machining. Finally, experimental results proved that cryogenic implementation can decrease the amount of heat transferred to the tool up to almost 70% and improve the surface roughness to a maximum of 31% when compared with dry machining.

scholarly journals Determination of Optimum Machining Condition for Surface Roughness Using Historical Data

2018 ◽  
Vol 7 (4.30) ◽  
pp. 73
Author(s):  
Mohd Shahfizal Mohd Ruslan ◽  
Haniff Abdul Rahman ◽  
Jaharah Abdul Ghani ◽  
Che Hassan Che Haron ◽  
Mohd Shahir Kassim ◽  
...  
Keyword(s):  
Surface Roughness ◽  
Magnesium Alloy ◽  
Optimum Condition ◽  
Feed Rate ◽  
High Speed ◽  
Historical Data ◽  
Cutting Speed ◽  
Weight Ratio ◽  
Depth Of Cut ◽  
Radial Depth

Magnesium alloy is one of the lightest materials with a high strength to weight ratio and excellent machinability, which makes it attractive and suitable for various industrial applications such as automotive and aerospace components. For these particular industrial components, the end products require a mirror-like finish. This article details a statistical analysis about the effect of milling parameters on the surface roughness of Magnesium alloy AZ91D in the dry milling process. The historical data approach in the response surface methodology (RSM) was utilized to determine the cause and effect relationship between the input variables and output response. The effect of milling parameter studied was cutting speed (900 – 1400 m/min), feed rate (0.03 - 0.09 mm/tooth), and radial depth of cut (0.2 - 0.3 mm). The results confirmed that the interaction between feed rate and cutting speed is the primary factor controlling the surface evolution. The responses of various factors were plotted using a two-dimensional interaction graph and the cubic empirical model was developed at 95% confidence level. The optimum condition for achieving the minimum surface roughness was a cutting speed of 977 m/min, a feed rate of 0.02 mm/tooth, and an axial depth of cut of 0.29 mm. With this optimum condition, a surface arithmetic roughness of 0.054 μm is expected. This study confirmed that by milling AZ91D at high speed cutting, it is possible to eliminate the polishing process to achieve a super mirror-like finishing.

TOOL LIFE PERFORMANCE OF COATED CARBIDE TOOL ON TITANIUM ALLOY EXTRA LOW INTERSTITIALS

2015 ◽  
Vol 77 (1) ◽  
Author(s):  
R. Zuraimi ◽  
M. A. Sulaiman ◽  
T. Joseph Sahaya Anand ◽  
E. Mohamad ◽  
C. H. Che Haron
Keyword(s):  
Tool Life ◽  
Feed Rate ◽  
Cutting Tool ◽  
Flank Wear ◽  
Cutting Speed ◽  
Weight Ratio ◽  
Chemical Vapor ◽  
Corrosion Property ◽  
Depth Of Cut ◽  
Coated Carbide

The Titanium alloys (Ti-6Al-4V) has been employed in a variety of applications, particularly in the aerospace, automotive, medical and chemical industries, primarily because of its high strength to weight ratio, high resistance to fracture, and exceptional anti-corrosion property. However, Ti-6Al-4V cannot be easily machined even at a high temperature as it has a low thermal conductivity and low elastic modulus, and may react chemically with the coating on the cutting tool. The objective of this study was to investigate the cutting tool life performance in the turning of Ti-6Al-4V Extra Low Interstitials (ELI) using a Chemical Vapor Deposition (CVD) carbide cutting tool in dry conditions. The Factorial method was used as the basis for the experimental design of this study. A factorial design with two levels was chosen for the arrangement of the cutting parameters, which comprised a cutting speed of between 100 to 140 m/min, a feed rate of between 0.15 to 0.20 mm/rev, and a fixed depth of cut of 0.35 mm. A three-axis microscope was used to measure the flank wear for every 20 mm on the workpiece until the ISO criterion was arrived at by the flank wear (Vb). The results indicated that the maximum tool life of 20.68 minutes was achieved at a cutting speed of 100 m/min and a feed rate of 0.15 mm/rev.

Sign in / Sign up

Export Citation Format

Share Document