Effect of Vaned Diffuser on a Modified Turbocharger Centrifugal Compressor Performance

2014 ◽  
Vol 663 ◽  
pp. 347-353
Author(s):  
Layth H. Jawad ◽  
Shahrir Abdullah ◽  
Zulkifli R. ◽  
Wan Mohd Faizal Wan Mahmood
Keyword(s):  
Centrifugal Compressor ◽  
Numerical Study ◽  
Pressure Ratio ◽  
Three Dimensional ◽  
Aerodynamic Characteristics ◽  
Width Ratio ◽  
Outlet Section ◽  
Suction Surface ◽  
Vaned Diffuser ◽  
Minimum Width

A numerical study that was made in a three-dimensional flow, carried out in a modified centrifugal compressor, having vaned diffuser stage, used as an automotive turbo charger. In order to study the influence of vaned diffuser meridional outlet section with a different width ratio of the modified centrifugal compressor. Moreover, the performance of the centrifugal compressor was dependent on the proper matching between the compressor impeller along the vaned diffuser. The aerodynamic characteristics were compared under different meridional width ratio. In addition, the velocity vectors in diffuser flow passages, and the secondary flow in cross-section near the outlet of diffuser were analysed in detail under different meridional width ratio. Another aim of this research was to study and simulate the effect of vaned diffuser on the performance of a centrifugal compressor. The simulation was undertaken using commercial software so-called ANSYS CFX, to predict numerically the performance charachteristics. The results were generated from CFD and were analysed for better understanding of the fluid flow through centrifugal compressor stage and as a result of the minimum width ratio the flow in diffuser passage tends to be uniformity. Moreover, the backflow and vortex near the pressure surface disappear, and the vortex and detachment near the suction surface decrease. Conclusively, it was observed that the efficiency was increased and both the total pressure ratio and static pressure for minimum width ratio are increased.

Numerical study on the Effect of Interaction Vaned Diffuser with Impeller on the Performance of a Modified Centrifugal Compressor

2013 ◽  
Vol 30 (2) ◽  
pp. 113-121 ◽  
Author(s):  
L. H. Jawad ◽  
S. Abdullah ◽  
R. Zulkifli ◽  
W. M. F. W. Mahmood
Keyword(s):  
Centrifugal Compressor ◽  
Numerical Study ◽  
Pressure Ratio ◽  
Three Dimensional ◽  
Internal Flow ◽  
Compressor Stage ◽  
Vaned Diffuser ◽  
Centrifugal Compressor Stage ◽  
Compressor Impeller ◽  
Inlet Conditions

ABSTRACTThis paper is a numerical simulation that was made in the three-dimensional flow, carried out in a modified centrifugal compressor, having vaned diffuser stage, used as an auto-motive turbo charger. Moreover, the performance of the centrifugal compressor was dependent on the proper matching between compressor impeller and vaned diffuser, influencing significantly surge and the efficiency of centrifugal compressor stages. In addition, a modified compressor impeller, coupled with vane and vaneless diffuser, has been found to have similar internal flow patterns for both the vaneless and vaned diffuser design. The vaned diffuser effect has been paid particular attention in terms of better analysis where the diffuser was designed for high sub-sonic inlet conditions. Another aim of this research was to study and simulate the effect of vaned diffuser on the performance of a centrifugal compressor. The simulation was undertaken by using a commercial software, the so-called ANSYS CFX, to predict numerically the performance in terms of pressure ratio, poly tropic efficiency and mass flow rate for the centrifugal compressor stage. The results were generated from CFD and were analyzed for better understanding of the fluid flow through centrifugal compressor stage. Conclusively, it was observed that the effect of the vaned diffuser is to convert the kinetic energy into a high static pressure after analyzing the results of the simulation.

Numerical Evaluation of the Unsteady Flow in a Centrifugal Compressor With Vaned Diffuser via URANS Approach

2016 ◽  
Author(s):  
Ali Zamiri ◽  
Byung Ju Lee ◽  
Jin Taek Chung
Keyword(s):  
Centrifugal Compressor ◽  
Stokes Equations ◽  
Pressure Ratio ◽  
Pressure Fluctuations ◽  
Three Dimensional ◽  
Frequency Noise ◽  
Computational Domain ◽  
Vaned Diffuser ◽  
Noise Characteristics ◽  
Time Space

The three dimensional, compressible, unsteady Navier-Stokes equations are solved to investigate the flow field of a centrifugal compressor with high compression ratio. Computational domain is consisted of an inlet bell and impeller with splitter blades followed by a two dimensional wedge vaned diffuser. The numerical method is validated by comparing the computational results with the experiments in terms of pressure ratio and compressor efficiency. The present study focuses on the unsteady pressure fluctuations and entropy production within the impeller and diffuser passages at the compressor design point. It is shown that the interaction between the impeller and diffuser blades leads to unsteadiness at the interface region and a pulsating behavior within the diffuser passages. Pressure waves with different convective velocities, generated by the impeller-diffuser interaction and pseudo-periodic unsteady separation bubbles, are captured in time/space domain along the diffuser blade surfaces. The pressure fluctuation spectra captured at the impeller-diffuser interface is evaluated to analyze the noise characteristics of the centrifugal compressor as a main source of blade passing frequency noise.

Experimental and Numerical Investigation of a Centrifugal Compressor and Numerical Study of the Area Ratio and Tip Clearance Effects on the Performance Characteristic

2008 ◽  
Author(s):  
Mahdi Nili-Ahmadabadi ◽  
Ali Hajilouy-Benisi ◽  
Mohammad Durali ◽  
Sayyed Mostafa Motavalli
Keyword(s):  
Flow Field ◽  
Centrifugal Compressor ◽  
Numerical Study ◽  
Pressure Ratio ◽  
Three Dimensional ◽  
Area Ratio ◽  
Tip Clearance ◽  
Performance Characteristics ◽  
Navier Stokes ◽  
Sst Turbulence Model

In this research, the centrifugal compressor of a turbocharger is investigated experimentally and numerically. Performance characteristics of the compressor were obtained experimentally by measurements of rotor speed and flow parameters at the inlet and outlet of the compressor. Three dimensional flow field in the impeller and diffuser was analyzed numerically using a full Navier-Stokes program with SST turbulence model. The performance characteristics of the compressor were obtained numerically, which were then compared with the experimental results. The comparison shows good agreement. Furthermore, the effect of area ratio and tip clearance on the performance parameters and flow field was studied numerically. The impeller area ratio was changed by cutting the impeller exit axial width from an initial value of 4.1 mm to a final value of 5.1 mm, resulting in an area ratio from 0.792 to 0.965. For the rotor with exit axial width of 4.6 mm, performance was investigated for tip clearance of 0.0, 0.5 and 1.0 mm. Results of this simulation at design point showed that the compressor pressure ratio peaked at an area ratio of 0.792 while the efficiency peaked at a higher value of area ratio of 0.878. Also the increment of the tip clearance from 0 to 1 mm resulted in 20 percent efficiency decrease.

Stability Improvement of a Turbocharger Centrifugal Compressor by a Nonaxisymmetric Vaned Diffuser

2018 ◽  
Vol 140 (4) ◽  
Author(s):  
Xinqian Zheng ◽  
Zhenzhong Sun ◽  
Tomoki Kawakubo ◽  
Hideaki Tamaki
Keyword(s):  
Flow Field ◽  
Flow Control ◽  
Centrifugal Compressor ◽  
Flow Separation ◽  
Static Pressure ◽  
Control Method ◽  
Numerical Study ◽  
Pressure Ratio ◽  
Vaned Diffuser ◽  
Positive Effects

The nonuniformity of the flow field induced by a nonaxisymmetric volute significantly degrades the stability of a turbocharger centrifugal compressor. In this paper, a nonaxisymmetric vaned diffuser is investigated as a nonaxisymmetric flow control method using both three-dimensional computational fluid dynamics (CFD) and experiment. The numerical study first focuses on the relationship between the flow field and the static pressure distortion, and the steady CFD results indicate that the positive static pressure gradient in the rotating direction facilitates flow separation in the vaned diffuser and induces a nonuniform flow field. A nonaxisymmetric flow control method with variable stagger and solidity of the vaned diffuser is developed to suppress the flow separation, and the guideline of the method suggests narrowing flow passages where the flow separates or closing diffuser vanes upstream of flow separations. Steady CFD also presents the flow field of the investigated turbocharger centrifugal compressor with volute, and flow separation is found in the flow passages near the volute tongue. Under the guidance of the nonaxisymmetric flow control method, several nonaxisymmetric vaned diffusers are designed to make the flow field uniform, which are believed to be beneficial for compressor stability. Finally, an experiment is carried out to validate the positive effects of the nonaxisymmetric vaned diffuser for stability improvement. The test data show that Non-AxisVD (with a nonaxisymmetric vaned diffuser) extends the stable flow range (SFR) of the compressor by 26% compared with the AxisVD (with an axisymmetric vaned diffuser), at the cost of acceptable decreases in the maximum total pressure ratio and peak efficiency.

Design and Off-Design Numerical Investigation of a Transonic Double-Splitter Centrifugal Compressor

2008 ◽  
Author(s):  
Michele Marconcini ◽  
Filippo Rubechini ◽  
Andrea Arnone ◽  
Seiichi Ibaraki
Keyword(s):  
Flow Field ◽  
Centrifugal Compressor ◽  
Cross Sections ◽  
Pressure Ratio ◽  
Three Dimensional ◽  
Secondary Flows ◽  
Operating Conditions ◽  
Complex Flow ◽  
Flow Measurements ◽  
Vaned Diffuser

The flow field of a high pressure ratio centrifugal compressor for turbocharger applications is investigated using a three-dimensional Navier-Stokes solver. The compressor is composed of a double-splitter impeller followed by a vaned diffuser. The flow field of the transonic open-shrouded impeller is highly three-dimensional, and it is influenced by shock waves, tip leakage vortices and secondary flows. Their interactions generate complex flow structures which are convected and distorted through the impeller blades. Both steady and unsteady computations are performed in order to understand the physical mechanisms which govern the impeller flow field while the operation ranges from choke to surge. Detailed Laser Doppler Velocimetry (LDV) flow measurements are available at various cross-sections inside the impeller blades at both design and off-design operating conditions.

Investigation of Unsteady Flow Field in a Vaned Diffuser of a Transonic Centrifugal Compressor

2006 ◽  
Vol 129 (4) ◽  
pp. 686-693 ◽  
Author(s):  
Seiichi Ibaraki ◽  
Tetsuya Matsuo ◽  
Takao Yokoyama
Keyword(s):  
Flow Field ◽  
Unsteady Flow ◽  
Centrifugal Compressor ◽  
Pressure Ratio ◽  
Flow Analysis ◽  
Three Dimensional ◽  
Flow Measurements ◽  
Vaned Diffuser ◽  
Transonic Compressor ◽  
Inlet Conditions

Transonic centrifugal compressors are used with high-load turbochargers and turboshaft engines. These compressors usually have a vaned diffuser to increase the efficiency and the pressure ratio. To improve the performance of such a centrifugal compressor, it is required to optimize not only the impeller but also the diffuser. However the flow field of the diffuser is quite complex and unsteady because of the impeller located upstream. Although some research on vaned diffusers has been published, the diffuser flow is strongly dependent on the particular impeller exit flow, and some of the flow physics remain to be elucidated. In the research reported here, detailed flow measurements within a vaned diffuser were conducted using a particle image velocimetery (PIV). The vaned diffuser was designed with high subsonic inlet conditions marked by an inlet Mach number of 0.95 for the transonic compressor. As a result, a complex three-dimensional flow with distortion between the shroud and the hub was observed. Also, unsteady flow accompanying the inflow of the impeller wake was confirmed. Steady computational flow analysis was performed and compared with the experimental results.

Numerical Analysis of the Vaned Diffuser of a Transonic Centrifugal Compressor

2010 ◽  
Vol 132 (4) ◽  
Author(s):  
Michele Marconcini ◽  
Filippo Rubechini ◽  
Andrea Arnone ◽  
Seiichi Ibaraki
Keyword(s):  
Flow Field ◽  
Centrifugal Compressor ◽  
Pressure Ratio ◽  
Three Dimensional ◽  
Navier Stokes ◽  
Flow Measurements ◽  
Vaned Diffuser ◽  
High Pressure Ratio ◽  
Unsteady Interaction ◽  
Inlet Conditions

A three-dimensional Navier–Stokes solver is used to investigate the flow field of a high pressure ratio centrifugal compressor for turbocharger applications. Such a compressor consists of a double-splitter impeller followed by a vaned diffuser. Particular attention is focused on the analysis of the vaned diffuser, designed for high subsonic inlet conditions. The diffuser is characterized by a complex three-dimensional flow field and influenced by the unsteady interaction with the impeller. Detailed particle image velocimetry flow measurements within the diffuser are available for comparison purposes.

Numerical Analysis of the Vaned Diffuser of a Transonic Centrifugal Compressor

2007 ◽  
Author(s):  
Michele Marconcini ◽  
Filippo Rubechini ◽  
Andrea Arnone ◽  
Seiichi Ibaraki
Keyword(s):  
Flow Field ◽  
Centrifugal Compressor ◽  
Pressure Ratio ◽  
Three Dimensional ◽  
Navier Stokes ◽  
Flow Measurements ◽  
Vaned Diffuser ◽  
High Pressure Ratio ◽  
Unsteady Interaction ◽  
Inlet Conditions

A three-dimensional Navier-Stokes solver is used to investigate the flow field of a high pressure ratio centrifugal compressor for turbocharger applications. Such a compressor consists of a double-splitter impeller followed by a vaned diffuser. Particular attention is focused on the analysis of the vaned diffuser, designed for high subsonic inlet conditions. The diffuser is characterized by a complex three-dimensional flow field, and influenced by the unsteady interaction with the impeller. Detailed Particle Image Velocimetry (PIV) flow measurements within the diffuser are available for comparison purposes.

Experimental and Numerical Investigations on a High Pressure Ratio Centrifugal Compressor

2005 ◽  
Author(s):  
Jae Ho Choi ◽  
Ok Suck Sung ◽  
Seung-Bae Chen ◽  
Jin Shik Lim
Keyword(s):  
Centrifugal Compressor ◽  
Performance Test ◽  
Pressure Ratio ◽  
Flow Analysis ◽  
Three Dimensional ◽  
Aerodynamic Characteristics ◽  
Design Flow ◽  
Tip Clearance ◽  
Centrifugal Impeller ◽  
Compressor Stage

An aerodynamic design, flow analysis and performance test of a pressure ratio 4:1 centrifugal compressor are presented in this paper. The compressor is made up of a centrifugal impeller, a two-stage diffuser consisted of radial and axial types. The impeller has a 45 degree backswept angle and the design running tip clearance is 5% of impeller exit height. Two types of diffusers are designed for this compressor. Three-dimensional numerical analysis is performed to analyze the flows in the impeller, diffuser and deswirler considering the impeller tip clearance. A test module and rig facilities for the compressor stage performance test are designed and fabricated. The overall compressor stage performances as well as the static pressure fields on the impeller and diffuser are measured. Two diffusers of wedge and airfoil types are tested with an impeller. The calculation and test results show the airfoil diffuser has the better aerodynamic characteristics than those of wedge diffuser in the studied models.

The Numerical Study on the Performance Evaluations and Flow Structures for the Diffuser of Centrifugal Compressor in a Marine Engine Turbocharger

2006 ◽  
Author(s):  
Hong-Won Kim ◽  
Seung-Hyup Ryu ◽  
Jong-Il Park ◽  
Sang-Hak Ghal ◽  
Ji-Soo Ha
Keyword(s):  
Centrifugal Compressor ◽  
High Efficiency ◽  
Numerical Study ◽  
Pressure Ratio ◽  
Prediction Method ◽  
Pressure Recovery ◽  
Vaneless Diffuser ◽  
Vaned Diffuser ◽  
Marine Engine ◽  
High Pressure Ratio

The centrifugal compressor of marine engine turbocharger is composed of impeller, 1st vaneless diffuser, vaned diffuser, 2nd vaneless diffuser and volute casing. An examination of the condition of the flow leaving the impeller exit kinetic energy often accounts for 30–50% of the shaft work input to the compressor stage, and for energy efficiency it is important to recover as much of this as possible. This is the function of the diffuser which follows the impeller. Effective pressure recovery downstream of an impeller is very important to realize a centrifugal compressor with high efficiency and high pressure ratio, and an appropriate selection of a diffuser for a specific impeller is a critical step to develop the compressor accordingly. The purpose of this study is to investigate the sensitivity of how compressor performances changes as vaned diffuser geometry is varied. Three kinds of vaned diffusers were studied and its results were compared. First vaned diffuser type is based on NACA airfoil and second is channel diffuser and third is conformal transformation of NACA 65 airfoil. Mean-line prediction method was applied to investigate the performance and stability for three kinds of diffusers. And CFD analyses have been done for comparison and detailed interior flow pattern study. In this study, the off design behavior of three different type of diffuser, given by mean-line prediction, was investigated using CFD results and selected best diffuser geometry which satisfy wider operating range and higher pressure recovery than the others. The numerical results were compared with experimental data for validation.

Sign in / Sign up

Export Citation Format

Share Document