Comparison of the Bearing Capacity of LST- Profile Depending on the Thickness of its Elements

2015 ◽  
Vol 725-726 ◽  
pp. 752-757 ◽  
Author(s):  
Darya Trubina ◽  
Dzhamal Abdulaev ◽  
Egor Pichugin ◽  
Vladimir Rybakov ◽  
Marsel Garifullin ◽  
...  
Keyword(s):  
Bearing Capacity ◽  
Cross Section ◽  
Local Buckling ◽  
Transverse Bending ◽  
Thin Walled ◽  
The Cross

The influence of local buckling on the bearing capacity of light steel thin-walled profiles is a hot topic today. In this paper we evaluated the effect of the thickness of the elements of the cross section on bearing capacity the profile in a transverse bending.

scholarly journals Computation of Thin-Walled Cross-Section Resistance to Local Buckling with the Use of the Critical Plate Method

2016 ◽  
Vol 62 (2) ◽  
pp. 229-264 ◽  
Author(s):  
A. Szychowski
Keyword(s):  
Cross Section ◽  
Critical Stress ◽  
Analytical Calculation ◽  
Local Buckling ◽  
Stability Loss ◽  
Longitudinal Stress ◽  
Plate Method ◽  
Thin Walled ◽  
The Cross ◽  
Elastically Restrained

Abstract Thin-walled bars currently applied in metal construction engineering belong to a group of members, the cross-section res i stance of which is affected by the phenomena of local or distortional stability loss. This results from the fact that the cross-section of such a bar consists of slender-plate elements. The study presents the method of calculating the resistance of the cross-section susceptible to local buckling which is based on the loss of stability of the weakest plate (wall). The “Critical Plate” (CP) was identified by comparing critical stress in cross-section component plates under a given stress condition. Then, the CP showing the lowest critical stress was modelled, depending on boundary conditions, as an internal or cantilever element elastically restrained in the restraining plate (RP). Longitudinal stress distribution was accounted for by means of a constant, linear or non-linear (acc. the second degree parabola) function. For the critical buckling stress, as calculated above, the local critical resistance of the cross-section was determined, which sets a limit on the validity of the Vlasov theory. In order to determine the design ultimate resistance of the cross-section, the effective width theory was applied, while taking into consideration the assumptions specified in the study. The application of the Critical Plate Method (CPM) was presented in the examples. Analytical calculation results were compared with selected experimental findings. It was demonstrated that taking into consideration the CP elastic restraint and longitudinal stress variation results in a more accurate representation of thin-walled element behaviour in the engineering computational model.

Geometric Nonlinearity of the Thin-Walled Profile under Transverse Bending

2014 ◽  
Vol 633-634 ◽  
pp. 1133-1139 ◽  
Author(s):  
Darya Trubina ◽  
Dzhamal Abdulaev ◽  
Egor Pichugin ◽  
Vladimir Rybokov
Keyword(s):  
Bearing Capacity ◽  
Geometric Nonlinearity ◽  
Local Buckling ◽  
Transverse Bending ◽  
Thin Walled

Local buckling and accounting of the geometric nonlinearity of light steel thin-walled profiles is an important topic. The authors assesses the influence of geometric nonlinearity on the bearing capacity profile in transverse bending conditions.

SETTING A DIAGRAM APPROACH TO CALCULATING VIBRATED, CENTRIFUGED AND VIBROCENTRIFUGED REINFORCED CONCRETE COLUMNS WITH A VARIATROPIC STRUCTURE

2020 ◽  
pp. 22-34
Author(s):  
Л. Р. Маилян ◽  
С. А. Стельмах ◽  
Е. М. Щербань ◽  
М. П. Нажуев
Keyword(s):  
Experimental Data ◽  
Reinforced Concrete ◽  
Bearing Capacity ◽  
Cross Section ◽  
Concrete Columns ◽  
Reinforced Concrete Columns ◽  
The Cross ◽  
Concrete Elements ◽  
Diagram Approach

Состояние проблемы. Железобетонные элементы изготавливаются, как правило, по трем основным технологиям - вибрированием, центрифугированием и виброцентрифугированием. Однако все основные расчетные зависимости для определения их несущей способности выведены, исходя из основного постулата - постоянства и равенства характеристик бетона по сечению, что реализуется лишь в вибрированных колоннах. Результаты. В рамках диаграммного подхода предложены итерационный, приближенный и упрощенный способы расчета несущей способности железобетонных вибрированных, центрифугированных и виброцентрифугированных колонн. Выводы. Расчет по диаграммному подходу показал существенно более подходящую сходимость с опытными данными, чем расчет по методике норм, а также дал лучшие результаты при использовании дифференциальных характеристик бетона, чем при использовании интегральных и, тем более, нормативных характеристик бетона. Statement of the problem. Reinforced concrete elements are typically manufactured according to three basic technologies - vibration, centrifugation and vibrocentrifugation. However, all the basic calculated dependencies for determining their bearing capacity were derived using the main postulate, i.e., the constancy and equality of the characteristics of concrete over the cross section, which is implemented only in vibrated columns. Results. Within the framework of the diagrammatic approach, iterative, approximate and simplified methods of calculating the bearing capacity of reinforced concrete vibrated, centrifuged and vibrocentrifuged columns are proposed. Conclusions. The calculation according to the diagrammatic approach showed a significantly better convergence with the experimental data than that using the method of norms, and also performs better when using differential characteristics of concrete than when employing integral and particularly standard characteristics of concrete.

scholarly journals Experimental and Numerical Study on Ultimate Shear Load Carrying Capacity of Corroded RC Beams

2021 ◽  
Vol 2021 ◽  
pp. 1-12
Author(s):  
Zhanzhan Tang ◽  
Zhixiang He ◽  
Zheng Chen ◽  
Lingkun Chen ◽  
Hanyang Xue ◽  
...  
Keyword(s):  
Shear Strength ◽  
Bearing Capacity ◽  
Cross Section ◽  
Loss Rate ◽  
Numerical Study ◽  
Rc Beams ◽  
Load Carrying ◽  
Shear Bearing Capacity ◽  
The Cross ◽  
The Impact

For an RC beam, the strength of steel rebar, the bonding strength between the concrete and reinforcement, and the bite action between the aggregates will deteriorate significantly due to corrosion. In the present study, 10 RC beams were designed to study the impact of corrosion on the shear bearing capacity. The mechanism of corrosion for stirrups and longitudinal bars and their effects were analyzed. Based on the existing experimental data, the correlation between the stirrup corrosion factor and the cross section loss rate was obtained. An effective prediction formula on the shear bearing capacity of the corroded RC beams was proposed and validated by the experimental results. Moreover, a numerical analysis approach based on the FE technique was proposed for the prediction of the shear strength. The results show that corrosion of the reinforcements could reduce the shear strength of the RC beams. The corrosion of stirrups can be numerically simulated by the reduction of the cross section. The formulae in the literature are conservative and the predictions are very dispersed, while the predictions by the proposed formula agree very well with the experiment results.

scholarly journals Research on Compression Behavior of Square Thin-Walled CFST Columns with Steel-Bar Stiffeners

2018 ◽  
Vol 8 (9) ◽  
pp. 1602 ◽  
Author(s):  
Zhao Yang ◽  
Chengxiang Xu
Keyword(s):  
Bearing Capacity ◽  
Local Buckling ◽  
Steel Tube ◽  
Steel Tubes ◽  
Compression Behavior ◽  
Steel Bar ◽  
Steel Bars ◽  
Thin Walled ◽  
Structural Measure ◽  
Cfst Columns

Local buckling in steel tubes was observed to be capable of reducing the ultimate loads of thin-walled concrete-filled steel-tube (CFST) columns under axial compression. To strengthen the steel tubes, steel bars were proposed in this paper to be used as stiffeners fixed onto the tubes. Static-loading tests were conducted to study the compression behavior of square thin-walled CFST columns with steel bar stiffeners placed inside or outside the tube. The effect and feasibility of steel bar stiffeners were studied through the analysis of failure mode, load–displacement relationship, ultimate load, ductility, and local buckling. Different setting methods of steel bars were compared as well. The results showed that steel-bar stiffeners proposed in this paper can be effective in delaying local buckling as well as increasing the bearing capacity of the columns, but will decrease the ductility of the columns. In order to obtain a higher bearing capacity of columns, steel bars with low stiffness should be placed inside and steel bars with high stiffness should be placed outside of the steel tubes. The study is helpful in providing reference to the popularization and application of this new structural measure to avoid or delay the local buckling of thin-walled CFST columns.

scholarly journals Buckling Analysis and Section Optimum for Square Thin-Wall CFST Columns Sealed by Self-Tapping Screws

2019 ◽  
Vol 2019 ◽  
pp. 1-14
Author(s):  
He Zhang ◽  
Kai Wu ◽  
Chao Xu ◽  
Lijian Ren ◽  
Feng Chen
Keyword(s):  
Bearing Capacity ◽  
Failure Modes ◽  
Steel Plate ◽  
Local Buckling ◽  
Steel Tube ◽  
Thin Wall ◽  
Type Section ◽  
Plate Buckling ◽  
Thin Walled ◽  
Cfst Columns

Two columns of thin-walled concrete-filled steel tubes (CFSTs), in which tube seams are connected by self-tapping screws, are axial compression tested and FEM simulated; the influence of local buckling on the column compression bearing capacity is discussed. Failure modes of square thin-wall CFST columns are, first, steel tube plate buckling and then the collapse of steel and concrete in some corner edge areas. Interaction between concrete and steel makes the column continue to withstand higher forces after buckling appears. A large deflection analysis for tube elastic buckling reflects that equivalent uniform stress of the steel plate in the buckling area can reach yield stress and that steel can supply enough designing stress. Aiming at failure modes of square thin-walled CFST columns, a B-type section is proposed as an improvement scheme. Comparing the analysis results, the B-type section can address both the problems of corner collapse and steel plate buckling. This new type section can better make full use of the stress of the concrete material and the steel material; this type section can also increase the compression bearing capacity of the column.

Design variation of thin-walled composite beam cross-section properties

2016 ◽  
Vol 12 (3) ◽  
pp. 558-576 ◽  
Author(s):  
Aníbal J.J. Valido ◽  
João Barradas Cardoso
Keyword(s):  
Cross Section ◽  
Cross Sections ◽  
Laminated Composite ◽  
Adjoint System ◽  
Design Sensitivity ◽  
Content Type ◽  
Design Elements ◽  
Thin Walled ◽  
The Cross ◽  
Cross Section Geometry

Purpose The purpose of this paper is to present a design sensitivity analysis continuum formulation for the cross-section properties of thin-walled laminated composite beams. These properties are expressed as integrals based on the cross-section geometry, on the warping functions for torsion, on shear bending and shear warping, and on the individual stiffness of the laminates constituting the cross-section. Design/methodology/approach In order to determine its properties, the cross-section geometry is modeled by quadratic isoparametric finite elements. For design sensitivity calculations, the cross-section is modeled throughout design elements to which the element sensitivity equations correspond. Geometrically, the design elements may coincide with the laminates that constitute the cross-section. Findings The developed formulation is based on the concept of adjoint system, which suffers a specific adjoint warping for each of the properties depending on warping. The lamina orientation and the laminate thickness are selected as design variables. Originality/value The developed formulation can be applied in a unified way to open, closed or hybrid cross-sections.

Collapse of Thin-Walled Elliptical Tubes for High Values of Major-to-Minor Axis Ratio

1993 ◽  
Vol 115 (4A) ◽  
pp. 432-440 ◽  
Author(s):  
C. Ribreau ◽  
S. Naili ◽  
M. Bonis ◽  
A. Langlet
Keyword(s):  
Contact Pressure ◽  
Cross Section ◽  
External Pressure ◽  
Straight Line Segment ◽  
Minor Axis ◽  
Cross Sectional ◽  
Axis Ratio ◽  
Straight Line ◽  
Thin Walled ◽  
The Cross

The topic of this study concerns principally representative models of some elliptical thin-walled anatomic vessels and polymeric tubes under uniform negative transmural pressure p (internal pressure minus external pressure). The ellipse’s ellipticity ko, defined as the major-to-minor axis ratio, varies from 1 up to 10. As p decreases from zero, at first the cross-section becomes somewhat oval, then the opposite sides touch in one point at the first-contact pressure pc. If p is lowered beneath pc, the curvature of the cross-section at the point of contact decreases until it becomes zero at the osculation pressure or the first line-contact pressure p1. For p<p1, the contact occurs along a straight-line segment, the length of which increases as p decreases. The pressures pc and p1 are determined numerically for various values of the wall thickness of the tubes. The nature of contact is especially described. The solution of the related nonlinear, two-boundary-values problem is compared with previous experimental results which give the luminal cross-sectional area (from two tubes), and the area of the mid-cross-section (from a third tube).

Structural bionic design for thin-walled cylindrical shell against buckling under axial compression

2011 ◽  
Vol 225 (11) ◽  
pp. 2619-2627 ◽  
Author(s):  
D Xing ◽  
W Chen ◽  
J Ma ◽  
L Zhao
Keyword(s):  
Cylindrical Shell ◽  
Axial Compression ◽  
Cross Section ◽  
Cylindrical Shells ◽  
High Load ◽  
Vascular Bundles ◽  
Bionic Design ◽  
Load Bearing ◽  
Thin Walled ◽  
The Cross

In nature, bamboo develops an excellent structure to bear nature forces, and it is very helpful for designing thin-walled cylindrical shells with high load-bearing efficiency. In this article, the cross-section of bamboo is investigated, and the feature of the gradual distribution of vascular bundles in bamboo cross-section is outlined. Based on that, a structural bionic design for thin-walled cylindrical shells is presented, of which the manufacturability is also taken into consideration. The comparison between the bionic thin-walled cylindrical shell and a simple hollow one with the same weight showed that the load-bearing efficiency was improved by 44.7 per cent.

Sign in / Sign up

Export Citation Format

Share Document