A Review on Butanol and Ethanol Fuels in Internal Combustion Engines

2016 ◽  
Vol 819 ◽  
pp. 259-264
Author(s):  
Abdullah Mustafa Hamid ◽  
Zulkarnain Abdul Latiff ◽  
Azhar Abdul Aziz ◽  
Mohd Rozi Mohd Perang
Keyword(s):  
Production Cost ◽  
Alternative Fuels ◽  
Internal Combustion Engines ◽  
Combustion Engine ◽  
Internal Combustion ◽  
Pollutant Emission ◽  
Combustion Engines ◽  
Ignition Timing ◽  
Greenhouse Gasses ◽  
Pollutant Gases

A controversial argument about alternative fuels is taking lots of researchers and scientists attention and so far ethanol and butanol, regardless their blending percentage, are the most promising alcohols due to their potential properties and low production cost. Many studies have been conducted to justify the optimum fuel to be implemented. In this work, a review will be conducted on both butanol and ethanol in internal combustion engine as well as their contribution in combustion engine regarding combustion performance, pollutant emission, ignition timing and knocking. According to the previous literature, an attractive advantage for alcohol-gasoline blends is that they don’t require engine modification design and still reduce the pollutant emission effectively. The properties of these fuels seem to prove not only that we can run our engines with a reduction of pollutant gases but with the emission of greenhouse gasses. This work will provide a review on ethanol and butanol as an alternative fuels and their properties and behaviour in the engine will be described individually.

scholarly journals Assessment of thermodynamic cycle of internal combustion engine in terms of rightsizing

2019 ◽  
Vol 178 (3) ◽  
pp. 182-186
Author(s):  
Zbigniew SROKA ◽  
Maciej DWORACZYŃSKI
Keyword(s):  
Internal Combustion Engine ◽  
Internal Combustion Engines ◽  
Combustion Engine ◽  
Combustion Process ◽  
Thermodynamic Cycle ◽  
Internal Combustion ◽  
Research Problem ◽  
Combustion Engines ◽  
Operating Characteristics ◽  
Swept Volume

The modification of the downsizing trend of internal combustion engines towards rightsizing is a new challenge for constructors. The change in the displacement volume of internal combustion engines accompanying the rightsizing idea may in fact mean a reduction or increase of the defining swept volume change factors and thus may affect the change in the operating characteristics as a result of changes in combustion process parameters - a research problem described in this publication. Incidents of changes in the displacement volume were considered along with the change of the compression space and at the change of the geometric degree of compression. The new form of the mathematical dependence describing the efficiency of the thermodynamic cycle makes it possible to evaluate the opera-tion indicators of the internal combustion engine along with the implementation of the rightsizing idea. The work demonstrated the in-variance of cycle efficiency with different forms of rightsizing.

FEATURES OF MEASURING THE CAMSHAFT OF INTERNAL COMBUSTION ENGINES

2021 ◽  
Vol 4 (30) ◽  
pp. 99-105
Author(s):  
A. V. Summanen ◽  
◽  
S. V. Ugolkov ◽  
Keyword(s):  
Internal Combustion Engine ◽  
Internal Combustion Engines ◽  
Combustion Engine ◽  
Internal Combustion ◽  
Technical Condition ◽  
Combustion Engines

This article discusses the issues of assessing the technical condition of the camshaft, internal combustion engine. The necessary parameters for assessing the technical condition of the engine camshaft have been determined. How and how to measure and calculate this or that parameter is presented in detail. Methods for calculating the parameters are presented. A scheme and method for measuring neck wear, determining the height of the cam, determining the beating of the central journal of the camshaft are proposed. The main defects of the camshafts are presented. The issues of the influence of these parameters on the operability of the camshaft and the internal combustion engine as a whole are considered.

Possibility of using gas lubricant in the cylinders of internal combustion engines of transport vehicles

2021 ◽  
pp. 13-20
Author(s):  
Keyword(s):  
Internal Combustion Engine ◽  
Bearing Capacity ◽  
Power Plants ◽  
Internal Combustion Engines ◽  
Combustion Engine ◽  
Internal Combustion ◽  
Combustion Engines ◽  
Engine Piston ◽  
Suspension Stiffness ◽  
Gas Layer

The prospects of using the gas-static suspension of the internal combustion engine piston in transport vehicles and power plants are considered. The diagram of the piston and the method for calculating the stiffness and bearing capacity of the gas layer surrounding the piston are presented, as well as the results of experiments that showed the relevance of this method. The possibility of gas and static centering of the engine piston is confirmed. Keywords: internal combustion engine, piston, gasstatic suspension, stiffness, bearing capacity, gas medium. [email protected]

Calculation of Acoustic Efficiency of Exhaust Silencers for Automotive Internal Combustion Engines

2021 ◽  
pp. 41-47
Author(s):  
Vladimir Tupov ◽  
O. Matasova
Keyword(s):  
Acoustic Waves ◽  
Internal Combustion Engines ◽  
Combustion Engine ◽  
Control Point ◽  
Plane Waves ◽  
Exhaust System ◽  
Internal Combustion ◽  
Combustion Engines ◽  
Exhaust Noise ◽  
Insertion Losses

Insertion losses as the main characteristic that mathematically describes the acoustic efficiency of a noise silencer has been considered. This characteristic shows the reduction of noise generated by its source, in particular by the internal combustion engine’s exhaust system, at the control point as a silencer use result. Has been presented a mathematical description of the insertion losses, and have been considered parameters necessary for calculating this characteristic. Has been demonstrated the analytical dependence of impedance for the sound emission by the exhaust system’s end hole from the coefficient of acoustic waves reflection by this hole. The performed analysis of the widely used formulas for calculating the coefficient of sound reflection by the end hole has showed their insufficient accuracy for project designs performing. Have been proposed calculation dependences providing high accuracy for calculations of the reflection coefficient modulus, and the attached length of the channel end hole without a flange in the entire range of the existence of plane waves in it. It has been shown that the end correction of this hole at ka = 0 is 0.6127, and not 0.6133, as it was mistakenly believed until now in world acoustics. Has been proposed a method for calculation the exhaust noise source internal impedance. This method more accurately, in comparison with the already known ones, describes the acoustic processes in the internal combustion engine’s exhaust manifold, thanks to increases the accuracy of calculation the silencer acoustic efficiency, that allows develop the silencer at the early stages of the design of an automotive internal combustion engine.

NH3 as a Transport Fuel in Internal Combustion Engines: A Technical Review

2019 ◽  
Vol 141 (7) ◽  
Author(s):  
Herry Lesmana ◽  
Zhezi Zhang ◽  
Xianming Li ◽  
Mingming Zhu ◽  
Wenqiang Xu ◽  
...  
Keyword(s):  
Alternative Fuels ◽  
Internal Combustion Engines ◽  
Internal Combustion ◽  
Combustion Engines ◽  
Nox Formation ◽  
Combustion Chemistry ◽  
Technical Review ◽  
Current State ◽  
Potential Applications ◽  
Homogenous Charge Compression Ignition

Ammonia (NH3) is an excellent hydrogen (H2) carrier that is easy to bulk manufacture, handle, transport, and use. NH3 is itself combustible and could potentially become a clean transport fuel for direct use in internal combustion engines (ICEs). This technical review examines the current state of knowledge of NH3 as a fuel in ICEs on its own or in mixtures with other fuels. A particular case of interest is to partially dissociate NH3 in situ to produce an NH3/H2 mixture before injection into the engine cylinders. A key element of the present innovation, the presence of H2 is expected to allow easy control and enhanced performance of NH3 combustion. The key thermochemical properties of NH3 are collected and compared to those of conventional and alternative fuels. The basic combustion characteristics and properties of NH3 and its mixtures with H2 are summarized, providing a theoretical basis for evaluating NH3 combustion in ICEs. The combustion chemistry and kinetics of NH3 combustion and mechanisms of NOx formation and destruction are also discussed. The potential applications of NH3 in conventional ICEs and advanced homogenous charge compression ignition (HCCI) engines are analyzed.

A Novel Way of Manipulating and Optimizing CAM Profiles for Internal Combustion Engines

2007 ◽  
Author(s):  
Satheesh Makkapati ◽  
Kim Ku ◽  
Steve Poe
Keyword(s):  
Internal Combustion Engines ◽  
Combustion Engine ◽  
Internal Combustion ◽  
Combustion Engines ◽  
Computationally Efficient ◽  
Trade Offs ◽  
Cam Profile ◽  
Computer Codes ◽  
Tool Optimization ◽  
Automated Tool

Generating an optimum cam profile for an internal combustion engine application is usually a very involved process. This is because of the challenge faced by the engine engineers to perform several trade-offs between fuel economy, performance, durability and emissions. Typically, the trade offs are worked out using several computer codes and with the involvement of a cross-functional team of engineers. Hence, there is a need to develop a tool that can encapsulate the various computer codes and can manipulate the cam profile with ease. With the existence of such an automated tool, optimization of the cam profile can be achieved with a specified trade-off between the several metrics identified above. This paper describes the development of such a tool, and discusses the ingredients that make it flexible and computationally efficient. Results from the use of this tool are documented in this paper as well.

Performance study of the hypocycloid gear mechanism for internal combustion engine applications

2019 ◽  
pp. 146808741989358 ◽  
Author(s):  
Mostafa A ElBahloul ◽  
ELsayed S Aziz ◽  
Constantin Chassapis
Keyword(s):  
Internal Combustion Engine ◽  
Thermodynamic Model ◽  
Internal Combustion Engines ◽  
Combustion Engine ◽  
Internal Combustion ◽  
Combustion Engines ◽  
Otto Cycle ◽  
Engine Efficiency ◽  
Gear Mechanism ◽  
Crank Mechanism

Fuel conversion efficiency is one of the main concerns in the field of internal combustion engine systems. Although the Otto cycle delivers the maximum efficiency possible in theory, the kinematics of the slider–crank mechanism of the conventional internal combustion engines makes it difficult to reach this level of efficiency in practice. This study proposes using the unique hypocycloid gear mechanism instead of the conventional slider–crank mechanism for the internal combustion engines to increase engine efficiency and minimize frictional power losses. The hypocycloid gear mechanism engine’s kinematics provides the means for the piston-rod assembly to reciprocate in a straight-line motion along the cylinder axis besides achieving a nonlinear rate of piston movement. As a result, this characteristic allows for a true constant-volume combustion, which in turn would lead to higher work output. An in-cylinder gas volume change model of the hypocycloid gear mechanism engine was developed and incorporated into the thermodynamic model for the internal combustion engine cycle. The thermodynamic model of the hypocycloid gear mechanism engine was developed and simulated using MATLAB/Simulink software. A comparison between the conventional engine and the hypocycloid gear mechanism engine in terms of engine performance characteristics showed the enhancements achieved using hypocycloid gear mechanism for internal combustion engine applications. The hypocycloid gear mechanism engine analysis results indicated higher engine efficiency approaching that of the Otto cycle.

Sign in / Sign up

Export Citation Format

Share Document