Research on Vibration Influence Chart of Planetary Gear Systems

2011 ◽  
Vol 86 ◽  
pp. 747-751 ◽  
Author(s):  
Le Hao Chang ◽  
Geng Liu ◽  
Li Yan Wu ◽  
Zhong Hong Bu

The common definition of vibration influence chart is proposed in this study. A 46 degree-of-freedom time-varying dynamic model with coupled translation-rotation effect is developed to simulate the vibration of an encased differential planetary gear system using lumped mass method. With the dynamic load and the acceleration on gears and bearings as references, the dynamic responses in different load cases are investigated to search the change law of concerned parameters. The parameters considered include mesh stiffness, structure stiffness, gear mass and moment of inertia. The good and poor regions for vibration are evidently presented in figures, which is convenient to conduct the parameters design of planetary gear systems.

Author(s):  
Sha Wei ◽  
Qinkai Han ◽  
Zhipeng Feng ◽  
Yanhua Shen ◽  
Fulei Chu

Planetary gear transmission system is one of the primary parts of the wind turbine drive train. Due to the assembly state, lubrication conditions and wear, the mesh stiffness of the planetary gear system is an uncertain parameter. In this paper, taking the uncertainty of mesh stiffness into account, the dynamic responses of a wind turbine gear system subjected to wind loads and transmission error excitations are studied. Firstly, a lumped-parameter model is extended to include both the planetary and parallel gears. Then the fluctuation ranges of dynamic mesh forces are predicted quantitatively and intuitively based on the combined Chebyshev interval inclusion function and numerical integration method. Finally, examples of gear trains with different interval mesh stiffnesses are simulated and the results show that tooth separations are becoming more obvious at the resonant speed by considering the fluctuating mesh stiffness of the second parallel gear stage. The nonlinear tooth separations are degenerated obviously as the fluctuation error of the mesh stiffness of the second parallel gear set is increased.


Author(s):  
Avtandil kyzy Ya

Abstract: This paper highlights similarities and different features of the category of kinesics “hand gestures”, its frequency usage and acceptance by different individuals in two different cultures. This study shows its similarities, differences and importance of the gestures, for people in both cultures. Consequently, kinesics study was mentioned as a main part of body language. As indicated in the article, the study kinesics was not presented in the Kyrgyz culture well enough, though Kyrgyz people use hand gestures a lot in their everyday life. The research paper begins with the common definition of hand gestures as a part of body language, several handshake categories like: the finger squeeze, the limp fish, the two-handed handshake were explained by several statements in the English and Kyrgyz languages. Furthermore, this article includes definitions and some idioms containing hand, shake, squeeze according to the Oxford and Academic Dictionary to show readers the figurative meanings of these common words. The current study was based on the books of writers Allan and Barbara Pease “The definite book of body language” 2004, Romana Lefevre “Rude hand gestures of the world”2011 etc. Key words: kinesics, body language, gestures, acoustics, applause, paralanguage, non-verbal communication, finger squeeze, perceptions, facial expressions. Аннотация. Бул макалада вербалдык эмес сүйлѳшүүнүн бѳлүгү болуп эсептелген “колдордун жандоо кыймылы”, алардын эки башка маданиятта колдонулушу, айырмачылыгы жана окшош жактары каралган. Макаланын максаты болуп “колдордун жандоо кыймылынын” мааниси, айырмасы жана эки маданиятта колдонулушу эсептелет. Ошону менен бирге, вербалдык эмес сүйлѳшүүнүн бѳлүгү болуп эсептелген “кинесика” илими каралган. Берилген макалада кѳрсѳтүлгѳндѳй, “кинесика” илими кыргыз маданиятында толугу менен изилденген эмес, ошого карабастан “кинесика” илиминин бѳлүгү болуп эсептелген “колдордун жандоо кыймылы” кыргыз элинин маданиятында кѳп колдонулат. Андан тышкары, “колдордун жандоо кыймылынын” бир нече түрү, англис жана кыргыз тилдеринде ма- селен аркылуу берилген.Тѳмѳнкү изилдѳѳ ишин жазууда чет элдик жазуучулардын эмгектери колдонулду. Түйүндүү сѳздѳр: кинесика, жандоо кыймылы, акустика,кол чабуулар, паралингвистика, вербалдык эмес баарлашуу,кол кысуу,кабыл алуу сезими. Аннотация. В данной статье рассматриваются сходства и различия “жестикуляции” и частота ее использования, в американской и кыргызской культурах. Следовательно, здесь было упомянуто понятие “кинесика” как основная часть языка тела. Как указано в статье, “кинесика” не была представлена в кыргызской культуре достаточно хорошо, хотя кыргызский народ часто использует жестикуляцию в повседневной жизни. Исследовательская работа начинается с общего определения “жестикуляции” как части языка тела и несколько категорий жестикуляции, таких как: сжатие пальца, слабое рукопожатие, рукопожатие двумя руками, были объяснены несколькими примерами на английском и кыргызском языках. Кроме того, эта статья включает определения слов “рука”, “рукопожатие”, “сжатие” и некоторые идиомы, содержащие данных слов согласно Оксфордскому и Академическому словарю, чтобы показать читателям их образное значение. Данное исследование было основано на книгах писателей Аллана и Барбары Пиз «Определенная книга языка тела» 2004 года, Романа Лефевра «Грубые жестикуляции мира» 2011 года и т.д. Ключевые слова: кинесика, язык жестов, жесты, акустика, аплодисменты, паралингвистика, невербальная коммуникация, сжатие пальца, чувство восприятия, выражение лиц.


Author(s):  
Jingyue Wang ◽  
Ning Liu ◽  
Haotian Wang ◽  
Jiaqiang E

Based on the lumped mass method, a torsional vibration model of the planetary gear system is established considering the nonlinear factors such as friction, time-varying meshing stiffness, backlash, and comprehensive error. The Runge–Kutta numerical method is used to analyze the motion characteristics of the system with various parameters and the influence of tooth friction on the bifurcation and chaos characteristics of the system. The numerical simulation results show that the system has rich bifurcation behavior with the excitation frequency, damping ratio, comprehensive error amplitude, load and backlash, and experiences multiple periodic motion and chaotic motion. Tooth friction makes the bifurcation behavior of the system fuzzy in the high frequency and heavy load areas, makes the chaos of the system restrained in the low-damping ratio and light load areas, advances the bifurcation point of the system in the small comprehensive error amplitude area, and makes the period window of the chaos area larger in the large-backlash area, which makes the bifurcation behavior of the system more complex.


Author(s):  
Jing Liu ◽  
Shizhao Ding ◽  
Linfeng Wang ◽  
Hongwu Li ◽  
Jin Xu

The bearing clearance, external torque, and input speed can greatly affect vibrations of the planetary gear system. The double-row planetary gear systems are commonly used in the gearbox of special vehicles, which are the key parts to obtain a larger gear ratio. Although many works have been presented to study those factors on vibrations of the single-row planetary gear system, a few works were focused on vibrations of the double-row planetary gear system with the bearing clearance. To overcome this problem, a multi-body dynamic model of a double-row planetary gear system with six planet bearings and one supported bearing of the sun gear is presented. This model is the main part of a gear box transmission system. The new model is developed for studying the effect of the bearing clearance on the planetary system. The meshing stiffness and damping between the gears are obtained by current methods in the listed references, as well as the contact stiffness and damping in bearings. The liner stiffness and damping model is used. The effects of the bearing clearance, external torque, and input speed on vibrations of the system are analyzed. The results show that vibrations of the ring gear and sun gear decrease with the increment of the external torque and increase with the increment of the input speed. Moreover, a reasonable bearing clearance can be helpful for reducing system vibrations for some mating external torque and input speed conditions. The results can provide some guidance to find new method to reduce vibrations and increase the service life of planetary gear systems.


2019 ◽  
Vol 7 (11) ◽  
pp. 405
Author(s):  
Zhou ◽  
Xu ◽  
Tang ◽  
Hu ◽  
He ◽  
...  

Dynamic responses of tuna purse seine to currents were numerically studied with regard to the vertical subsidence and global load distribution, and determinant attributes were identified. We rebuilt the submerged geometry of a purse seine net using the lumped mass method with hydrodynamic coefficients obtained from measurements of the prototype material, as well as a mesh grouping method, which corrects the twine diameter and netting material density for the equivalent net by introducing the compensation coefficient. Uneven tension distribution showed that it was vulnerable to high loads in the bunt area at shooting and along the lead line at pursing. High loads were present at the convex sections of net circles in the direction of the current. Higher shooting speeds resulted in well-balanced sinking, while a reduced hanging ratio of netting panels was beneficial to faster sinking. While large mesh sizes reduce water resistance and increase sinking velocity, extensive use should be cautioned in terms of the sensibility to stress. Comparing two options of different proportions of large-mesh panels, mesh sizes doubled for 15 strips versus 5 strips, suggesting that the 15 strip option would pose a higher risk of strand vulnerability, while the 5 strip option may be a more balanced alternative with a lower mesh density and a lower mesh stress.


2018 ◽  
Vol 32 (8) ◽  
pp. 3537-3545 ◽  
Author(s):  
Mohsen Rezaei ◽  
Mehrdad Poursina ◽  
Shahram Hadian Jazi ◽  
Farhad Haji Aboutalebi

2018 ◽  
Vol 189 ◽  
pp. 06009 ◽  
Author(s):  
Xiaogang Liu ◽  
Zhaoyu Wu ◽  
Weiguang Shu ◽  
Jie Lu

The drive shaft arrangement has a considerable influence on the vibration responses of the shaft-final drive system. In this research, a coupled vibration model is developed based on force analysis of hypoid gear and lumped mass method. The effect of time-varying mesh stiffness, gear backlash and transfer error are included to investigate the effect of the angle between drive shafts on vibration responses of main reducer. The vibration responses of main reducer are acquired using this model. The results show that the vibration amplitude of the gears of main reducer increase with the angle between drive shafts. This paper presents an analytical method to determine the value of the angle between drive shafts, so as to control the vibration of main reducer.


2003 ◽  
Vol 19 (1) ◽  
pp. 89-109 ◽  
Author(s):  
KARSTEN KLINT JENSEN

It is common to define egalitarianism in terms of an inequality ordering, which is supposed to have some weight in overall evaluations of outcomes. Egalitarianism, thus defined, implies that levelling down makes the outcome better in respect of reducing inequality; however, the levelling down objection claims there can be nothing good about levelling down. The priority view, on the other hand, does not have this implication. This paper challenges the common view. The standard definition of egalitarianism implicitly assumes a context. Once this context is made clear, it is easily seen that egalitarianism could be defined alternatively in terms of valuing a benefit to a person inversely to how well off he is relative to others. The levelling down objection does not follow from this definition. Moreover, the common definition does not separate egalitarian orderings from prioritarian ones. It is useful to do this by requiring that on egalitarianism, additively separable orderings should be excluded. But this requirement is stated as a condition on the alternative definition of egalitarianism, from which the levelling down objection does not follow.


Sign in / Sign up

Export Citation Format

Share Document