Effect of Plating Solutions on Supercapacitor Characteristics of MnO2 Films

2010 ◽  
Vol 113-116 ◽  
pp. 1810-1813
Author(s):  
Fang Xiao ◽  
You Long Xu
Keyword(s):  
Electrode Materials ◽  
Electrochemical Impedance ◽  
Equivalent Circuit Model ◽  
Active Surface ◽  
Charge Transfer Resistance ◽  
Electrochemical Impedance Spectrum ◽  
Active Surface Area ◽  
Cyclic Voltammograms ◽  
Supercapacitor Electrode ◽  
Transfer Resistance

MnO2 films were electrodeposited on the Ti substrates by galvanostatic method in various plating solutions, which was MnCl2, Mn(NO3)2, MnSO4 and Mn(CH3COO)2 solutions, respectively. On X-ray diffraction test, Crystal structures of all MnO2 films were associated to α-MnO2 of tetragonal crystal system. Scanning electron microscopy results show that morphologies of MnO2 films were clearly different. Among them, MnO2 film prepared in Mn(CH3COO)2 solution presented a lot of cracks and holes. According to electrochemical impedance spectrum analysis, this MnO2 film presents the lowest charge-transfer resistance. Additionally, electrochemical active surface areas of MnO2 films were calculated on the basis of equivalent circuit model for impedance data. The result was found that MnO2 film prepared in Mn(CH3COO)2 solution showed the biggest electrochemical active surface area, which was about 382 cm2. Cyclic voltammograms were carried out for all the samples. MnO2 film formed in Mn(CH3COO)2 solution showed the highest special capacitance of 230 F g-1. The results suggest that Mn(CH3COO)2 solution is suitable for electrodepositing MnO2 film using supercapacitor electrode materials.

Ultrathin nickel boride nanosheets anchored on functionalized carbon nanotubes as bifunctional electrocatalysts for overall water splitting

2019 ◽  
Vol 7 (2) ◽  
pp. 764-774 ◽  
Author(s):  
Xuncai Chen ◽  
Zixun Yu ◽  
Li Wei ◽  
Zheng Zhou ◽  
Shengli Zhai ◽  
...  
Keyword(s):  
Carbon Nanotubes ◽  
Charge Transfer ◽  
Active Surface ◽  
Charge Transfer Resistance ◽  
Active Surface Area ◽  
Transfer Resistance ◽  
Functionalized Carbon Nanotubes ◽  
Electrochemically Active ◽  
Metal Borides ◽  
Electrochemically Active Surface

Carbon nanotubes increase electrochemically active surface area and reduce charge transfer resistance of transition metal borides.

scholarly journals Electrochemical Characterization of CVD-Grown Graphene for Designing Electrode/Biomolecule Interfaces

Crystals ◽  
2020 ◽  
Vol 10 (4) ◽  
pp. 241
Author(s):  
Keishu Miki ◽  
Takeshi Watanabe ◽  
Shinji Koh
Keyword(s):  
Electrochemical Properties ◽  
Electrode Materials ◽  
Electrochemical Impedance ◽  
Chemical Vapor ◽  
Charge Transfer Resistance ◽  
Monolayer Graphene ◽  
Transfer Resistance ◽  
Graphene Electrode ◽  
Before And After ◽  
Modified Graphene

In research on enzyme-based biofuel cells, covalent or noncovalent molecular modifications of carbon-based electrode materials are generally used as a method for immobilizing enzymes and/or mediators. However, the influence of these molecular modifications on the electrochemical properties of electrode materials has not been clarified. In this study, we present the electrochemical properties of chemical vapor deposition (CVD)-grown monolayer graphene electrodes before and after molecular modification. The electrochemical properties of graphene electrodes were evaluated by cyclic voltammetry and electrochemical impedance measurements. A covalently modified graphene electrode showed an approximately 25-fold higher charge transfer resistance than before modification. In comparison, the electrochemical properties of a noncovalently modified graphene electrode were not degraded by the modification.

scholarly journals A Low Cost Fe3O4–Activated Biochar Electrode Sensor by Resource Utilization of Excess Sludge for Detecting Tetrabromobisphenol A

Micromachines ◽  
2022 ◽  
Vol 13 (1) ◽  
pp. 115
Author(s):  
Suxing Luo ◽  
Meizhi Yang ◽  
Yuanhui Wu ◽  
Jiang Li ◽  
Jun Qin ◽  
...  
Keyword(s):  
Electrochemical Sensors ◽  
Low Cost ◽  
Active Surface ◽  
Charge Transfer Resistance ◽  
Tetrabromobisphenol A ◽  
Active Surface Area ◽  
Excess Sludge ◽  
Transfer Resistance ◽  
Activated Biochar ◽  
Bet Analysis

Owing to its ubiquity in natural water systems and the high toxicity of its accumulation in the human body, it is essential to develop simple and low-cost electrochemical sensors for the determination of 3,3′,5,5′-tetrabromobisphenol A (TBBPA). In this work, Fe3O4–activated biochar, which is based on excess sludge, was prepared and characterized using scanning electron microscopy (SEM), energy dispersive spectroscopy (EDS), Fourier transform infrared spectroscopy (FTIR) and BET analysis to analyze its basic features. Subsequently, it was used to fabricate an electrochemical sensor for the detection of TBBPA. The electrochemical test results revealed that the Fe3O4–activated biochar film exhibited a larger active surface area, a lower charge transfer resistance and a higher accumulation efficiency toward TBBPA. Consequently, the peak current of TBBPA was significantly enhanced on the surface of the Fe3O4–activated biochar. The TBBPA sensing platform developed using the Fe3O4–activated biochar composite film, with relatively a lower detection limit (3.2 nM) and a wider linear range (5–1000 nM), was successfully utilized to determine TBBPA levels in water samples. In summary, the effective application of Fe3O4–activated biochar provided eco-friendly and sustainable materials for the development of a desirable high-sensitivity sensor for TBBPA detection.

Enhanced Electrochemical Performances of LiFePO4/C Cathode Materials by Deposited with Ge Film

2014 ◽  
Vol 936 ◽  
pp. 480-485
Author(s):  
Yan Dan Huang ◽  
Ying Bin Lin ◽  
Zhi Gao Huang
Keyword(s):  
Impedance Spectroscopy ◽  
Electrochemical Impedance ◽  
Active Material ◽  
Rate Capability ◽  
Film Surface ◽  
Charge Transfer Resistance ◽  
Electrochemical Performances ◽  
Cyclic Voltammograms ◽  
Transfer Resistance ◽  
Surface Modified

LiFePO4/C-Ge electrodes were prepared with vacuum thermal evaporation deposition by depositing Ge films on as-prepared LiFePO4/C electrodes. The effect of Ge film on the electrochemical performances of LiFePO4/C cells was investigated systematically by charge/discharge testing, cyclic voltammograms and AC impedance spectroscopy, respectively. It was found that Ge-film-surface modified LiFePO4/C showed excellent electrochemical performances compared to that of the pristine one in terms of cyclability and rate capability. At 60°C, LiFePO4/C-Ge film exhibited outstanding cyclability with less than 5% capacity fade after 50 cycles while the pristine one suffers 15%. Analysis from the electrochemical measurements showed that the presence of Ge film on the LiFePO4/C electrode would protect active material from HF generated by the decomposition of LiPF6 in the electrolyte and stabilize the surface structure of active material during the charge and discharge cycle. Electrochemical impedance spectroscopy (EIS) results indicated that Ge film mainly reduced the charge transfer resistance Rct of LiFePO4/C electrode, resulting from the suppression of the solid electrolyte interfacial (SEI) film.

Synthesis and Electrochemical Properties of Y-Doped SnO2/C Composite Materials for Lithium-Ion Battery

2011 ◽  
Vol 197-198 ◽  
pp. 1157-1162 ◽  
Author(s):  
Sheng Kui Zhong ◽  
You Wang ◽  
Chang Jiu Liu ◽  
Yan Wei Li ◽  
Yan Hong Li
Keyword(s):  
Particle Size ◽  
Electrochemical Impedance ◽  
Electronic Conductivity ◽  
Lithium Ion ◽  
Charge Transfer Resistance ◽  
Precipitation Method ◽  
Cyclic Voltammograms ◽  
Sem Images ◽  
Electrochemical Impedance Spectra ◽  
Transfer Resistance

The layered Y-doped SnO2/C anode materials were prepared by a co-precipitation method. The physical properties of the Y-doped SnO2/C were investigated by X-ray diffraction (XRD), scanning electron microscopy (SEM), and electrochemical measurements. XRD studies showed that the Y-doped SnO2/C has the same layered structure as the undoped SnO2/C. The SEM images exhibited that the particle size of Y-doped SnO2/C is smaller than that of the undoped SnO2/C and the smallest particle size is only about 1µm. The Y-doped SnO2/C samples were investigated on the Lithium extraction/insertion performances by charge/discharge, cyclic voltammograms (CV), and electrochemical impedance spectra (EIS). The results showed that the optimal doping content of Y was that x=0.07 and 2% content of carbon nanotubes samples to achieve high discharge capacity and good cyclic stability. The electrode reaction reversibility and electronic conductivity were enhanced, and the charge transfer resistance was decreased through Y-doping.

scholarly journals Electro-Oxidation of Ammonia over Copper Oxide Impregnated γ-Al2O3 Nanocatalysts

Coatings ◽  
2021 ◽  
Vol 11 (3) ◽  
pp. 313
Author(s):  
Safia Khan ◽  
Syed Sakhawat Shah ◽  
Mohsin Ali Raza Anjum ◽  
Mohammad Rizwan Khan ◽  
Naveed Kausar Janjua
Keyword(s):  
Electron Microscopy ◽  
Diffusion Coefficient ◽  
Electrode Materials ◽  
Electrochemical Impedance ◽  
Active Surface ◽  
Alkaline Media ◽  
Active Surface Area ◽  
Structural Investigations ◽  
Al2o3 Support ◽  
Electro Oxidation

Ammonia electro-oxidation (AEO) is a zero carbon-emitting sustainable means for the generation of hydrogen fuel, but its commercialization is deterred due to sluggish reaction kinetics and the poisoning of expensive metal electrocatalysts. With this perspective, CuO impregnated γ-Al2O3 (CuO/γ-Al2O3) hybrid materials were synthesized as effective and affordable electrocatalysts and investigated for AEO in alkaline media. Structural investigations were performed via different characterization techniques, i.e., X-ray diffraction (XRD), Fourier transformed infrared spectroscopy (FTIR), scanning electron microscopy (SEM), transmission electron microscopy (TEM), and electrochemical impedance spectroscopy (EIS). The morphology of γ-Al2O3 support as interconnected porous structures rendered the CuO/γ-Al2O3 nanocatalysts with robust activity. The additional CuO impregnation resulted in the enhanced electrochemical active surface area (ECSAs) and diffusion coefficient and spiked the electrocatalytic performance for NH3 electrolysis. Owing to good values of diffusion coefficient for AEO, low bandgap, and availability of ample ECSA at higher CuO to γ-Al2O3 ratio, these proposed electrocatalysts were proved to be effective in AEO. Due to good reproducibility, electrochemical stability, and higher activity for ammonia electro-oxidation, CuO/γ-Al2O3 nanomaterials are proposed as efficient promoters, electrode materials, or catalysts in ammonia electrocatalysis.

scholarly journals Bioleaching and Electrochemical Behavior of Chalcopyrite by a Mixed Culture at Low Temperature

2021 ◽  
Vol 12 ◽  
Author(s):  
Tangjian Peng ◽  
Wanqing Liao ◽  
Jingshu Wang ◽  
Jie Miao ◽  
Yuping Peng ◽  
...  
Keyword(s):  
Low Temperature ◽  
Mixed Culture ◽  
Pure Culture ◽  
High Throughput Sequencing ◽  
Electrochemical Impedance ◽  
Corrosion Current ◽  
Charge Transfer Resistance ◽  
Microbial Consortia ◽  
Cyclic Voltammograms ◽  
Transfer Resistance

Low-temperature biohydrometallurgy is implicated in metal recovery in alpine mining areas, but bioleaching using microbial consortia at temperatures <10°C was scarcely discussed. To this end, a mixed culture was used for chalcopyrite bioleaching at 6°C. The mixed culture resulted in a higher copper leaching rate than the pure culture of Acidithiobacillus ferrivorans strain YL15. High-throughput sequencing technology showed that Acidithiobacillus spp. and Sulfobacillus spp. were the mixed culture’s major lineages. Cyclic voltammograms, potentiodynamic polarization and electrochemical impedance spectroscopy unveiled that the mixed culture enhanced the dissolution reactions, decreased the corrosion potential and increased the corrosion current, and lowered the charge transfer resistance and passivation layer impedance of the chalcopyrite electrode compared with the pure culture. This study revealed the mechanisms via which the mixed culture promoted the chalcopyrite bioleaching.

Preparation and electrochemical characterization of PANI/MnCo2O4 nanocomposite as supercapacitor electrode material

2018 ◽  
Vol 96 (5) ◽  
pp. 477-483 ◽  
Author(s):  
Saeid Panahi ◽  
Moosa Es’haghi
Keyword(s):  
Specific Capacitance ◽  
Surface Characterization ◽  
Electrochemical Impedance ◽  
Rate Capability ◽  
Cycling Performance ◽  
Charge Transfer Resistance ◽  
X Ray Diffraction ◽  
Supercapacitor Electrode ◽  
Transfer Resistance

In this work, PANI/MnCo2O4 nanocomposite was prepared via in-situ chemical polymerization method. Materials synthesized were characterized by FTIR spectroscopy, X-ray diffraction, and scanning electron spectroscopy. In addition, surface characterization of samples such as specific surface area, pore volume, and pore size distribution was studied. Supercapacitor capability of materials was investigated in 1 mol L–1 Na2SO4 solution using cyclic voltammetry in different potential scan rates and electrochemical impedance spectroscopy (EIS). The specific capacitance of materials was calculated, and it was observed that the specific capacitance of PANI/MnCo2O4 nanocomposite was 185 F g−1, much larger than PANI. Moreover, the prepared nanocomposite exhibited better rate capability in scan rate of 100 mV s−1 with respect to PANI. The EIS experiments revealed that the nanocomposite has lower charge transfer resistance compared with pure PANI. Subsequently, it was shown that the nanocomposite cycling performance was superior to the PANI cycling performance.

scholarly journals Influence of Fe and Ni Doped CuO Nanomaterials for High Performance Supercapacitors

2020 ◽  
Vol 32 (11) ◽  
pp. 2763-2772
Author(s):  
Palanisamy Revathi ◽  
Venkatachalam Ma nikandan ◽  
Panneerselvam Ezhilmathi ◽  
Veerasamy Uma Shankar ◽  
Palani Suganya ◽  
...  
Keyword(s):  
High Performance ◽  
Electrochemical Impedance ◽  
Sol Gel ◽  
Charge Transfer Resistance ◽  
Cyclic Voltammograms ◽  
Transfer Resistance ◽  
Galvanostatic Discharge ◽  
Low Charge ◽  
Supercapacitor Applications ◽  
Eis Analysis

This paper focuses on the synthesis of doped and undoped CuO nanoparticles using the sol-gel method, which has been prepared and described. Supercapacitor applications of as-synthesized nanomaterials were analyzed using cyclic voltammetry (CV), galvanostatic discharge (GCD) and electrochemical impedance spectroscopic (EIS) analysis. The cyclic voltammograms illustrated the quasi-rectangular shape which depicted the pseudocapacitance nature of the samples. The calculated specific capacitance of the prepared samples was 180, 253 and 303 (F/g) corresponding to CuO, Fe-CuO and Ni-CuO, respectively at the low current density and the EIS spectra show that the prepared Ni-CuO electrode exhibits low charge transfer resistance.

Production and Electrochemical Characterization of Nickel Based Composite Coatings Containing Chromium Group Metal and Silicon Powders

2015 ◽  
Vol 228 ◽  
pp. 219-224
Author(s):  
Magdalena Popczyk ◽  
Julian Kubisztal ◽  
Bożena Łosiewicz ◽  
A. Budniok
Keyword(s):  
Steady State ◽  
Electrode Materials ◽  
Electrochemical Impedance ◽  
Composite Coatings ◽  
Active Surface ◽  
Electrochemical Activity ◽  
Active Surface Area ◽  
Electrochemically Active ◽  
Electrochemically Active Surface

The Ni+Cr+Si, Ni+Mo+Si and Ni+W+Si composite coatings were obtained by electrodeposition of crystalline nickel from an electrolyte containing suspension of suitable metallic and non-metallic components (Cr, Mo, W and Si). These coatings were obtained galvanostatically at the current density of jdep = -0.100 A cm-2 and at the temperature of 338 K. Chemical composition of the coatings was determined by energy dispersive spectroscopy (EDS). The electrochemical activity of these electrocatalysts was studied in the process of hydrogen evolution reaction (HER) in 5 M KOH solution using steady-state polarization and electrochemical impedance spectroscopy (EIS) methods. The kinetic parameters of the HER on particular electrode materials were determined. It was found that Ni+Mo+Si composite coatings are characterized by enhanced electrochemical activity towards the HER as compared with Ni+W+Si and Ni+Cr+Si coatings due to the presence of Mo and increase in electrochemically active surface area.

Sign in / Sign up

Export Citation Format

Share Document