The Experimental Investigation of the Effects of Different Chip Breaker Forms on the Cutting Forces

2007 ◽  
Vol 23 ◽  
pp. 191-194 ◽  
Author(s):  
Huseyin Gürbüz ◽  
Adem Kurt ◽  
I. Korkut ◽  
Ulvi Şeker
Keyword(s):  
Experimental Investigation ◽  
Cutting Forces ◽  
Manufacturing Industry ◽  
Cutting Parameters ◽  
Cutting Conditions ◽  
Depth Of Cut ◽  
Test Results ◽  
Workpiece Material ◽  
Chip Breaker ◽  
Cutting Speeds

The objective of this paper is experimentally investigation of the effects of different chip breaker forms on the cutting forces according to various cutting parameters. AISI 1050 workpiece material, most used material in the manufacturing industry, and SNMG 120408R inserts and PSBNR 2525M12 tool holder have 75° approaching angle according to ISO 3685 are used in the experiments. Seven groups chip breaker form were used in the tests. The chip breaker forms are the coated inserts MA, SA, MS, GH and standard, and the uncoated inserts MS and standard. These inserts are Mitsubishi UC 6010 and UTI20T grade; correspond to ISO P30 and P15 grade, respectively. Machining tests were carried out by using five levels of cutting speeds (150, 200, 250, 300, 350 m/min), three levels of feed rate (0.15, 0.25, 0.35 mm/rev) and two levels of depth of cut (1.6, 2.5 mm). Cutting forces were measured using Kistler dynamometer. The test results show that the highest cutting force values were measured on SA, GH, MA forms, respectively. Complex chip breaker forms cause the increase of the cutting forces. Although the cutting forces on the uncoated inserts were partly small in light cutting conditions, it has increased on the uncoated inserts in heavy cutting conditions compared to coated inserts.

scholarly journals Experimental Investigation and Statistical Evaluation of Optimized Cutting Process Parameters and Cutting Conditions to Minimize Cutting Forces and Shape Deviations in Al6026-T9

Materials ◽  
2020 ◽  
Vol 13 (19) ◽  
pp. 4327 ◽  
Author(s):  
Muhammad Abas ◽  
Bashir Salah ◽  
Qazi Salman Khalid ◽  
Iftikhar Hussain ◽  
Abdur Rehman Babar ◽  
...  
Keyword(s):  
Feed Rate ◽  
Cutting Forces ◽  
Virgin Olive Oil ◽  
Cutting Parameters ◽  
Cutting Conditions ◽  
Depth Of Cut ◽  
Signal To Noise ◽  
Shape Deviations ◽  
Measuring Machine ◽  
Tungsten Carbide Tool

Precise, economical and sustainable cutting operations are highly desirable in the advanced manufacturing environment. For this aim, the present study investigated the influence of cutting parameters (i.e., the cutting speed (c), feed rate (f), depth of cut (d) and positive rake angle (p)) and sustainable cutting conditions (dry and minimum quantity lubricant (MQL)) on cutting forces (i.e., feed force (Ff), tangential forces (Ft), radial force (Fr) and resultant cutting forces (Fc) and shape deviations (i.e., circularity and cylindricity) of a 6026-T9 aluminum alloy. The type of lubricant and insert used are virgin olive oil and uncoated tungsten carbide tool. Turning experiments were performed on a TAKISAWA TC-1 CNC lathe machine and cutting forces were measured with the help of a Kistler 9257B dynamometer. Shape deviations were evaluated by means of a Tesa Micro-Hite 3D DCC 474 coordinate measuring machine (CMM). Experimental runs were planned based on Taguchi mixture orthogonal array design L16. Analysis of variance (ANOVA) was performed to study the statistical significance of cutting parameters. Taguchi based signal to noise (S/N) ratios are applied for optimization of single response, while for optimization of multiple responses Taguchi based signal to noise (S/N) ratios coupled with multi-objective optimization on the basis of ratio analysis (MOORA) and criteria importance through inter-criteria correlation (CRITIC) are employed. ANOVA results revealed that feed rate, followed by a depth of cut, are the most influencing and contributing factors for all components of cutting forces (Ff, Ft, Fr, and Fc) and shape deviations (circularity and cylindricity). The optimized cutting parameters obtained for multi responses are c = 600 m/min, f = 0.1 mm/rev, d = 1 mm and p = 25°, while for cutting conditions, MQL is optimal.

Cutting Forces and Tool Wear in Dry Milling of Ti6Al4V

2012 ◽  
Vol 565 ◽  
pp. 454-459 ◽  
Author(s):  
Yun Chen ◽  
Huai Zhong Li ◽  
Jun Wang
Keyword(s):  
Tool Wear ◽  
Cutting Forces ◽  
Cutting Speed ◽  
Depth Of Cut ◽  
Dry Milling ◽  
Workpiece Material ◽  
Tool Wear Mechanism ◽  
Coated Carbide ◽  
Carbide Inserts ◽  
Cutting Speeds

Titanium alloys are difficult-to-cut materials. This paper presents an experimental study of the effects of different cutting conditions and tool wear on cutting forces in dry milling Ti6Al4V with coated carbide inserts. The experimental results show that the peak forces increase with the increase in the feed rate and depth of cut. With the cutting speed increment in the range from 50 m/min to 150 m/min the peak forces decrease, while at further higher cutting speeds investigated peak forces increase. The decrease of the peak forces is due to thermal softening of the workpiece material and the increase is because of the strain hardening rate of Ti6Al4V. The tool wear experiment reveals that the major tool wear mechanism is the flank wear. The variations of the peak forces are caused by both the tool wear propagation and the thermal effects.

Studying The Effect of a New Mixed Cutting Fluid on Surface Roughness

2020 ◽  
Vol 38 (11A) ◽  
pp. 1593-1601
Author(s):  
Mohammed H. Shaker ◽  
Salah K. Jawad ◽  
Maan A. Tawfiq
Keyword(s):  
Surface Roughness ◽  
Stainless Steel ◽  
Cutting Parameters ◽  
Machining Process ◽  
Cutting Fluid ◽  
Depth Of Cut ◽  
Cutting Fluids ◽  
Machining Processes ◽  
Dry Cutting ◽  
Cutting Speeds

This research studied the influence of cutting fluids and cutting parameters on the surface roughness for stainless steel worked by turning machine in dry and wet cutting cases. The work was done with different cutting speeds, and feed rates with a fixed depth of cutting. During the machining process, heat was generated and effects of higher surface roughness of work material. In this study, the effects of some cutting fluids, and dry cutting on surface roughness have been examined in turning of AISI316 stainless steel material. Sodium Lauryl Ether Sulfate (SLES) instead of other soluble oils has been used and compared to dry machining processes. Experiments have been performed at four cutting speeds (60, 95, 155, 240) m/min, feed rates (0.065, 0.08, 0.096, 0.114) mm/rev. and constant depth of cut (0.5) mm. The amount of decrease in Ra after the used suggested mixture arrived at (0.21µm), while Ra exceeded (1µm) in case of soluble oils This means the suggested mixture gave the best results of lubricating properties than other cases.

OPTIMISING CUTTING PARAMETERS FOR HOT TURNING ON EN31 MATERIAL

2021 ◽  
Vol 5 (10) ◽  
Author(s):  
Prof. Hemant k. Baitule ◽  
Satish Rahangdale ◽  
Vaibhav Kamane ◽  
Saurabh Yende
Keyword(s):  
Surface Roughness ◽  
Surface Finish ◽  
Cutting Speed ◽  
Cutting Parameters ◽  
Machining Process ◽  
Depth Of Cut ◽  
Multiple Time ◽  
Turning Process ◽  
Workpiece Material ◽  
Hot Turning

In any type of machining process the surface roughness plays an important role. In these the product is judge on the basis of their (surface roughness) surface finish. In machining process there are four main cutting parameter i.e. cutting speed, feed rate, depth of cut, spindle speed. For obtaining good surface finish, we can use the hot turning process. In hot turning process we heat the workpiece material and perform turning process multiple time and obtain the reading. The taguchi method is design to perform an experiment and L18 experiment were performed. The result is analyzed by using the analysis of variance (ANOVA) method. The result Obtain by this method may be useful for many other researchers.

Machining Evaluation of High-Speed Milling for Thin-Wall Machining of Al7075-T651

2014 ◽  
Vol 541-542 ◽  
pp. 785-791 ◽  
Author(s):  
Joon Young Koo ◽  
Pyeong Ho Kim ◽  
Moon Ho Cho ◽  
Hyuk Kim ◽  
Jeong Kyu Oh ◽  
...  
Keyword(s):  
Surface Roughness ◽  
Surface Integrity ◽  
Cutting Forces ◽  
High Speed ◽  
Surface Condition ◽  
Cutting Conditions ◽  
Depth Of Cut ◽  
Thin Wall ◽  
Machined Surface ◽  
High Speed Milling

This paper presents finite element method (FEM) and experimental analysis on high-speed milling for thin-wall machining of Al7075-T651. Changes in cutting forces, temperature, and chip morphology according to cutting conditions are analyzed using FEM. Results of machining experiments are analyzed in terms of cutting forces and surface integrity such as surface roughness and surface condition. Variables of cutting conditions are feed per tooth, spindle speed, and axial depth of cut. Cutting conditions to improve surface integrity were investigated by analysis on cutting forces and surface roughness, and machined surface condition.

Predictive Modeling and Optimization of Cutting Forces Through RSM and Taguchi Techniques in the Turning of ASTM B574 (Hastelloy C-22)

2018 ◽  
pp. 398-417
Author(s):  
İsmail Kırbaş ◽  
Musa Peker ◽  
Gültekin Basmacı ◽  
Mustafa Ay
Keyword(s):  
Feed Rate ◽  
Cutting Forces ◽  
Cutting Speed ◽  
Cutting Parameters ◽  
Rake Angle ◽  
Orthogonal Experimental Design ◽  
Depth Of Cut ◽  
Effective Parameters ◽  
Factors Affecting ◽  
The Impact

In this chapter, the impact of cutting parameters (depth of cut, cutting speed, feed, flow, rake angle, lead angle) on cutting forces in the turning process with regard to ASTM B574 (Hastelloy C-22) material has been investigated. Variance analysis has been applied in order to determine the factors affecting the cutting forces. The optimization of the parameters affecting the surface roughness has been obtained using response surface methodology (RSM) based on the Taguchi orthogonal experimental design. The accuracy of the developed models required for the estimation of the force values (Fx, Fy, Fz) is quite successful. In this study, where the R2 value has been used as the criterion/measure, accuracy values of 93.35%, 95.03%, and 95.09% have been achieved for Fx, Fy, and Fz, respectively. As a result of the ANOVA analysis, the most effective parameters for Fx at a 95% confidence interval are depth of cut, feed rate, flow, and rake angle. The most effective parameter for Fy is depth of cut, while the most effective parameters for Fz are depth of cut, feed rate, and flow, respectively.

scholarly journals Stability analysis for a single-point cutting tool deflection in turning operation

2019 ◽  
Vol 11 (6) ◽  
pp. 168781401985318
Author(s):  
Amon Gasagara ◽  
Wuyin Jin ◽  
Angelique Uwimbabazi
Keyword(s):  
Cutting Forces ◽  
High Speed ◽  
Cutting Tool ◽  
Single Point ◽  
Three Dimensional ◽  
High Speed Steel ◽  
Cutting Parameters ◽  
Depth Of Cut ◽  
Beam Model ◽  
Tool Deflection

In this article, a new model of regenerative vibrations due to the deflection of the cutting tool in turning is proposed. The previous study reported chatter as a result of cutting a wavy surface of the previous cut. The proposed model takes into account cutting forces as the main factor of tool deflection. A cantilever beam model is used to establish a numerical model of the tool deflection. Three-dimensional finite element method is used to estimate the tool permissible deflection under the action of the cutting load. To analyze the system dynamic behavior, 1-degree-of-freedom model is used. MATLAB is used to compute the system time series from the initial value using fourth-order Runge–Kutta numerical integration. A straight hard turning with minimal fluid application experiment is used to obtain cutting forces under stable and chatter conditions. A single-point cutting tool made from high-speed steel is used for cutting. Experiment results showed that for the cutting parameters above 0.1mm/rev feed and [Formula: see text]mm depth of cut, the system develops fluctuations and higher chatter vibration frequency. Dynamic model vibration results showed that the cutting tool deflection induces chatter vibrations which transit from periodic, quasi-periodic, and chaotic type.

scholarly journals Investigation of the Subsurface Temperature Effects on Nanocutting Processes via Molecular Dynamics Simulations

Metals ◽  
2020 ◽  
Vol 10 (9) ◽  
pp. 1220
Author(s):  
Michail Papanikolaou ◽  
Francisco Rodriguez Hernandez ◽  
Konstantinos Salonitis
Keyword(s):  
Molecular Dynamics ◽  
Molecular Dynamics Simulations ◽  
Process Parameters ◽  
Cutting Forces ◽  
Rake Angle ◽  
Von Mises Stress ◽  
Depth Of Cut ◽  
Subsurface Temperature ◽  
Workpiece Material ◽  
Dynamics Simulations

In this investigation, three-dimensional molecular dynamics simulations have been performed in order to investigate the effects of the workpiece subsurface temperature on various nanocutting process parameters including cutting forces, friction coefficient, as well as the distribution of temperature and equivalent Von Mises stress at the subsurface. The simulation domain consists of a tool with a negative rake angle made of diamond and a workpiece made of copper. The grinding speed was considered equal to 100 m/s, while the depth of cut was set to 2 nm. The obtained results suggest that the subsurface temperature significantly affects all of the aforementioned nanocutting process parameters. More specifically, it has been numerically validated that, for high subsurface temperature values, thermal softening becomes dominant and this results in the reduction of the cutting forces. Finally, the dependency of local properties of the workpiece material, such as thermal conductivity and residual stresses on the subsurface temperature has been captured using numerical simulations for the first time to the authors’ best knowledge.

Life Prediction of Cutting Tool by the Workpiece Cutting Condition

2011 ◽  
Vol 223 ◽  
pp. 554-563 ◽  
Author(s):  
Noemia Gomes de Mattos de Mesquita ◽  
José Eduardo Ferreira de Oliveira ◽  
Arimatea Quaresma Ferraz
Keyword(s):  
Cutting Tool ◽  
Cutting Tools ◽  
Cutting Speed ◽  
Cutting Parameters ◽  
Operating Conditions ◽  
Production Costs ◽  
Depth Of Cut ◽  
Cutting Condition ◽  
Workpiece Material ◽  
The Cost

Stops to exchange cutting tool, to set up again the tool in a turning operation with CNC or to measure the workpiece dimensions have direct influence on production. The premature removal of the cutting tool results in high cost of machining, since the parcel relating to the cost of the cutting tool increases. On the other hand the late exchange of cutting tool also increases the cost of production because getting parts out of the preset tolerances may require rework for its use, when it does not cause bigger problems such as breaking of cutting tools or the loss of the part. Therefore, the right time to exchange the tool should be well defined when wanted to minimize production costs. When the flank wear is the limiting tool life, the time predetermination that a cutting tool must be used for the machining occurs within the limits of tolerance can be done without difficulty. This paper aims to show how the life of the cutting tool can be calculated taking into account the cutting parameters (cutting speed, feed and depth of cut), workpiece material, power of the machine, the dimensional tolerance of the part, the finishing surface, the geometry of the cutting tool and operating conditions of the machine tool, once known the parameters of Taylor algebraic structure. These parameters were raised for the ABNT 1038 steel machined with cutting tools of hard metal.

Sign in / Sign up

Export Citation Format

Share Document