Bending Properties of Three-Layer Biaxial Weft Knitted Fabric Reinforced Composite Materials

2011 ◽  
Vol 295-297 ◽  
pp. 1217-1220 ◽  
Author(s):  
Ye Xiong Qi ◽  
Jia Lu Li ◽  
Liang Sen Liu
Keyword(s):  
Composite Materials ◽  
Fiber Volume Fraction ◽  
Bending Strength ◽  
Volume Fraction ◽  
Knitted Fabric ◽  
Bending Properties ◽  
Fiber Volume ◽  
Reinforced Composite ◽  
Weft Knitted Fabric ◽  
Load Deflection Curve

In this paper, three-layer biaxial weft knitted fabric(TBWK) made of carbon fiber as inserted yarns and polyester yarns as knitted yarns , which is a kind of non-crimp fabric, has been impregnated with epoxy via RTM technique. The bending properties of the TBWK fabric reinforced composite materials with different fiber volume fraction have been investigated. The bending strength of TBWK reinforced composites with fiber volume fraction of 48.8% can reach 821.1 MPa. The results show that this kind of composites has good bending properties, and load - deflection curve shows obvious linear features.

Bending Properties of Four-Layer Biaxial Weft Knitted Fabric Reinforced Composite Materials

2012 ◽  
Vol 182-183 ◽  
pp. 89-92
Author(s):  
Liang Sen Liu ◽  
Ye Xiong Qi ◽  
Jia Lu Li
Keyword(s):  
Composite Materials ◽  
Composite Laminates ◽  
Fiber Volume Fraction ◽  
Bending Strength ◽  
Volume Fraction ◽  
Bending Properties ◽  
Fiber Volume ◽  
Reinforced Composite ◽  
Weft Knitted Fabric ◽  
Bending Load

In this paper, a kind of composite laminates whose reinforcement is four-layer biaxial weft knitted (FBWK)fabric made of carbon fiber as inserted yarns has been made. The composite laminates have been impregnated with epoxy resin via resin transfer molding (RTM) technique. The samples of the experiments have been made from the composite laminates. The bending properties of the FBWK fabric reinforced composite materials with different fiber volume fraction have been investigated. The results show that the bending strength of this kind of composites increases with the fiber volume fraction increasing. The bending strength of FBWK reinforced composites with fiber volume fraction of 52% can reach 695.86 MPa. And the relationship between bending load and deflection is obviously linear.

Bending Properties of Five-Layer Biaxial Weft Knitted Fabric Reinforced Composite Materials

2011 ◽  
Vol 391-392 ◽  
pp. 359-363 ◽  
Author(s):  
Wei Geng ◽  
Ye Xiong Qi ◽  
Jia Lu Li
Keyword(s):  
Composite Materials ◽  
Fiber Volume Fraction ◽  
Bending Strength ◽  
Volume Fraction ◽  
Test Method ◽  
Bending Test ◽  
Bending Properties ◽  
Fiber Volume ◽  
Reinforced Composite ◽  
Bending Load

Five-layer biaxial weft knitted (FBWK) fabric is one kind of multilayered biaxial weft knitted (MBWK) fabric. FBWK fabric is made of carbon fiber as inserted yarns and stitched with polyester yarns, and it has been impregnated with epoxy via resin transfer molding (RTM) technique to manufacture the composite plates. The bending properties of the FBWK fabric reinforced composite are studied with the three-point bending test method. The bending properties of the FBWK fabric reinforced composite materials with different fiber volume fraction have been investigated. The results show that the relationship between bending load and deflection is obviously linear before reaching the maximum load. Within a certain range, the bending strength of this kind of composites increases with the fiber volume fraction increasing. When the fiber volume fraction is 57%, the bending strength is 1051.4 MPa.

The Effects of Fiber Volume Fraction on the Vibration Damping Characteristics of Three-Layer-Connected Biaxial Weft Knitted Fabric Reinforced Composite Materials

2012 ◽  
Vol 602-604 ◽  
pp. 49-52
Author(s):  
Jing Xue Liu ◽  
Jia Lu Li
Keyword(s):  
Fiber Volume Fraction ◽  
Volume Fraction ◽  
Damping Ratio ◽  
Vibration Damping ◽  
Knitted Fabric ◽  
Vibration Modes ◽  
Fiber Volume ◽  
Damping Behavior ◽  
Weft Knitted Fabric ◽  
Vibration Parameters

The paper presents an analysis of the vibration damping properties of three-layer-connected biaxial weft knitted fabric (TBWK), which are constituted of carbon fibers as inserted yarns and polyester yarns as knitted yarns impregnated in an epoxy matrix with resin transfer molding (RTM) technique. Damping parameters were investigated using beam test specimens and an impulse technique. Several vibration parameters were varied to characterize the damping behavior in different amplitudes, natural frequencies and vibration modes. The results obtained show that the damping ratio of TBWK composites decreases with the increasing of fiber volume fraction in all the three vibration modes. The vibration test also indicates that the natural frequency of the TBWK composites increases with the increasing of fiber volume fraction (Vf) in all the three modes.

scholarly journals Pengaruh Penambahan Serat Batang Pisang Ketip dan Filler Dedak Padi Terhadap Density, Kekuatan Bending dan Tarik Kompositcore, Sandwich dengan Skin Plywood

MECHANICAL ◽  
2019 ◽  
Vol 10 (1) ◽  
pp. 1
Author(s):  
Salman Salman ◽  
Ahmad Fadly
Keyword(s):  
Tensile Strength ◽  
Fiber Volume Fraction ◽  
Bending Strength ◽  
Volume Fraction ◽  
Sandwich Composite ◽  
Fiber Direction ◽  
Fiber Volume ◽  
Banana Fiber ◽  
Fiber Reinforced Composite ◽  
Reinforced Composite

Fiber-reinforced composite core banana stems with additional filler of husk powder is another way to obtain the expected mechanical behavior of the composite. The aim of this study was to analyze the effect of fiber volume fraction content to density, bending strength and tensile strength of sandwich composite.   Preparation of composite was done by hand lay-up method. Composite material used by banana ketip  fiber and addition of husk powder with variation of fiber volume fraction were 7, 10, and 13 % where husk was constant at 5% with random fiber direction. Tests were conducted by referring to the density est standard (ASTM C 271), bending est (ASTM C 393) and tensile test (ASTM D3039).  The result showed that the greater volume fraction of banana fiber, the lower the density value and the lower the bending strength. Whereas the tensile strength tended to increase as the volume fraction was higher.

Mechanics of Natural Composites

1990 ◽  
Vol 218 ◽  
Author(s):  
Joseph E. Saliba ◽  
Rebecca C. Schiavone ◽  
Stephen L. Gunderson ◽  
Denise G. Taylor
Keyword(s):  
Composite Materials ◽  
Modulus Of Elasticity ◽  
Fiber Volume Fraction ◽  
Volume Fraction ◽  
Structural Response ◽  
Sensitivity Study ◽  
Fiber Volume ◽  
Fiber Size ◽  
Natural Composites ◽  
As Stress

AbstractThis study was initiated to investigate the structural response of the bessbeetle to determine potential advantageous ramifications and effects on the optimization of synthetic composite materials. The result of the micromechanics sensitivity study of various parameters are presented. Variables such as fiber size and shape, fiber volume fraction, ratio of modulus of elasticity of fiber over matrix, are changed one variable at a time, and the response quantities such as stress and tranverse modulus are presented.

scholarly journals Peningkatan Sifat Mekanik Komposit Serat Alam Limbah Sabut Kelapa (Cocofiber) yang Biodegradable

2021 ◽  
Vol 6 (1) ◽  
pp. 30-37
Author(s):  
Sri Hastuti ◽  
Herru Santosa Budiono ◽  
Diki Ilham Ivadiyanto ◽  
Muhammad Nurdin Nahar
Keyword(s):  
Mechanical Properties ◽  
Fiber Volume Fraction ◽  
Bending Strength ◽  
Natural Fiber ◽  
Volume Fraction ◽  
Fiber Composites ◽  
Coconut Fiber ◽  
Fiber Volume ◽  
Coconut Coir ◽  
The Impact

Inovasi baru serat dari sabut kelapa dimanfaatkan untuk meningkatkan nilai ekonomis dari serat sabut kelapa, oleh karena itu dirancanglah pendayagunaan serat dari sabut kelapa untuk penguat komposit dengan material serat alam yang biodegradable. Hal ini untuk mendukung penggunaan komposit yang ramah terhadap lingkungan dan mengurangi penggunaan material komposit serat sintetis yang polutan. Tujuan penelitian adalah menganalisis sifat mekanik pada komposit serat alam bermaterial serat dari sabut kelapa yang ramah lingkungan. Metode penelitian pembuatan komposit berpenguat serat dari sabut kelapa dilakukan treatment NaOH 15% selama 5 jam dan fraksi volume serat 10 %, 15 %, dan 20 %. Komposit  serat dari sabut kelapa dengan matriks UPRs 157 BQTN dengan hardener MEXPO. Pengujian mekanik dilakukan uji bending menggunakan standar ASTM D790 dan uji impak  menggunakan standar ASTM D5941.  Pengujian impak komposit serat alam menunjukkan ketangguhan impak komposit pada fraksi volume serat 20% dengan nilai 0.017588J/mm2. Hasil pengujian menunjukkan peningkatan fraksi volume serta berpengaruh terhadap peningkatan kekuatan bending komposit serat dari sabut kelapa  dengan kekuatan optimum bending pada fraksi volume serat 10% dengan nilai 44,33N/mm2. Hal ini menunjukkan peningkatan fraksi volume serat dengan perendaman NaOH 15% akan meningkatkan sifat mekanik bending dan impak komposit. Perendaman NaOH memberikan pengaruh daya serap sabut kelapa terhadap matrik Unsaturated Polyester yang dapat meningkatkan daya rekat antara penguat serat dengan matrik sehingga meningkatkan sifat mekanik bending dan impak komposit. ABSTRACT The innovation of coco fiber is used to increase the economic value of coconut coir, therefore the utilization of coconut fiber for reinforcing composites with biodegradable natural fiber material is designed. This is to support the use of composites that are friendly to the environment and reduce the use of pollutant synthetic fiber composite materials. The research objective was to analyze the mechanical properties of natural fiber composites with environmentally friendly coconut fiber as material. The research method of making fiber-reinforced composites from coconut coir was carried out by 15% NaOH treatment for 5 hours and a fiber volume fraction of 10%, 15%, and 20%. Composite fiber from coconut coir with UPRs 157 BQTN matrix with MEXPO hardener. Mechanical testing is carried out using the ASTM D790 standard and the impact test using the ASTM D5941 standard. The impact test of natural fiber composites showed the impact toughness of the composite at a fiber volume fraction of 20% with a value of 0.017588 J/ mm2. The test results showed an increase in volume fraction and an effect on the increase in the bending strength of coconut fiber composites with the optimum bending strength at a fiber volume fraction of 10% with a value of 44.33N /mm2. This shows that the increase in fiber volume fraction by immersion in 15% NaOH will increase the bending mechanical properties and the impact of the composite. Soaking NaOH has an effect on the absorption power of coconut coir on the Unsaturated Polyester matrix which can increase the adhesion between the fiber reinforcement and the matrix thereby increasing the bending mechanical properties and impact of the composite.

Fabrication of Two Dimensional Silicon Carbide Fiber-Reinforced Silicon Carbide Composite by Electrophoretic Deposition and Hot-Pressing

2007 ◽  
Vol 352 ◽  
pp. 77-80 ◽  
Author(s):  
Katsumi Yoshida ◽  
Hideki Matsumoto ◽  
Masamitsu Imai ◽  
Kazuaki Hashimoto ◽  
Yoshitomo Toda ◽  
...  
Keyword(s):  
Silicon Carbide ◽  
Electrophoretic Deposition ◽  
Hot Pressing ◽  
Fracture Behavior ◽  
Fiber Volume Fraction ◽  
Bending Strength ◽  
Volume Fraction ◽  
Fiber Volume ◽  
The Difference ◽  
Sic Composites

In this study, Tyranno SA fiber cloth was coated with carbon black and SiC powder containing sintering aids by means of electrophoretic deposition method, and SiC/SiC composites with three different fiber volume fractions were fabricated using the Tyranno SA cloth by hot-pressing at 1700oC. The sufficient formation of the SiC matrix between each fiber could be observed. The composite fractured in non-brittle manner, and bending strength decreased with increasing fiber volume fraction. The crack propagation and fracture behavior depended on the fiber volume fraction. These differences in bending strength and fracture behavior would be caused by the difference in the interfacial bonding between fiber cloth and the matrix.

Fatigue damage analysis of fiber-reinforced polymer composites—A review

2018 ◽  
Vol 37 (9) ◽  
pp. 636-654 ◽  
Author(s):  
Md. Touhid Alam Ansari ◽  
Kalyan Kumar Singh ◽  
Mohammad Sikandar Azam
Keyword(s):  
Composite Materials ◽  
Polymer Composites ◽  
Fatigue Damage ◽  
Fiber Volume Fraction ◽  
Volume Fraction ◽  
Fiber Reinforced Polymer ◽  
Fiber Reinforced ◽  
Fiber Volume ◽  
Reinforced Polymer ◽  
Fiber Reinforced Polymer Composites

Fiber-reinforced polymer composites are becoming suitable and substantial materials in the repair and replacement of conventional metallic materials because of their high strength and stiffness. These composites undergo various types of static and fatigue loads during service. One of the major tests that conventional and composite materials have to experience is fatigue test. It refers to the testing for the cyclic behavior of materials. Composite materials are different from metals, as they indicate a distinct behavior under fatigue loading. The fatigue damage and failure mechanisms are more intricate in composite materials than in metals in which a crack initiates and propagates up to fracture. In composite materials, several micro-cracks initiate at the primary stage of the fatigue growth, resulting in the initiation of various types of fatigue damage. Fiber volume fraction is an important parameter to describe a composite laminate. The fatigue strength increases with the increase of the fiber volume fraction to a certain level and then decreases because of the lack of enough resin to grip the fibers. The fatigue behavior of fiber-reinforced polymer composites depends on various factors, e.g., constituent materials, manufacturing process, hysteresis heating, fiber orientation, type of loading, interface properties, frequency, mean stress, environment. This review paper explores the effects of various parameters like fiber type, fiber orientation, fiber volume fraction, etc. on the fatigue behavior of fiber-reinforced polymer composites.

Sign in / Sign up

Export Citation Format

Share Document