The Effects of Low Flow Rate Gas Involvement on Oil-Water Flow in Horizontal Pipes

2011 ◽  
Vol 354-355 ◽  
pp. 41-44
Author(s):  
Hai Qin Wang ◽  
Lei Zhang ◽  
Yong Wang ◽  
De Xuan Li
Keyword(s):  
Water Flow ◽  
Flow Rate ◽  
Flow Characteristics ◽  
Considerable Effect ◽  
Low Flow ◽  
Horizontal Pipes ◽  
Test Loop ◽  
Three Phase Flow ◽  
Oil Water ◽  
Low Flow Rate

The experiments were conducted in a horizontal multiphase flow test loop (50mm inner diameter, 40m long) to investigate the flow of oil/water and the influence of an involved gas phase with low flow rate in horizontal pipes, specifically including oil/water flow patterns, cross-section water holdup and pipe flow pressure gradient. The experimental results indicated that the involved gas with low flow rate had a considerable effect on oil/water flow characteristics, which shows the complexity of gas/oil/water three-phase flow. Thus, this effect could not be ignored in design and operation management of oil/gas gathering and transportation system.

Inter-Blade Vortex Characteristics With the Blockage Effects of Runner Blade in a Francis Hydro Turbine Model

2019 ◽  
Author(s):  
Seung-Jun Kim ◽  
Jin-Hyuk Kim ◽  
Young-Seok Choi ◽  
Yong Cho ◽  
Jong-Woong Choi
Keyword(s):  
Flow Rate ◽  
Flow Characteristics ◽  
Internal Flow ◽  
Operating Conditions ◽  
Low Flow ◽  
Hydro Turbine ◽  
Runner Blade ◽  
Performance Reduction ◽  
Turbine Model ◽  
Low Flow Rate

Abstract This study presents the numerical analysis on the inter-blade vortex characteristics along with the blockage effects of runner blade in a Francis hydro turbine model with various flow rate conditions. The turbine model showed different flow characteristics in the runner blade passages according to operating conditions, and inter-blade vortex was observed at lower flow rate conditions. This inter-blade vortex can lead to performance reduction, vibration, and instability for smooth operation of turbine systems. The previous study on blockage effects on various runner blade thickness, showed its influence on hydraulic performance and internal flow characteristics at low flow rate conditions. Therefore, the inter-blade vortex characteristics can be altered with the blockage effects at low flow rate conditions in a Francis hydro-turbine. For investigating the internal flow and unsteady pressure characteristics, three-dimensional steady and unsteady Reynolds-averaged Navier-Stokes calculations are performed. These inter-blade vortices were captured at the leading and trailing edges close to the runner hub. These vortex regions showed flow separation and stagnation flow while blockage effects contributed for decreasing the inter-blade vortex at low flow rate conditions.

scholarly journals Unsteady Characteristics of Forward Multi-Wing Centrifugal Fan at Low Flow Rate

Processes ◽  
2019 ◽  
Vol 7 (10) ◽  
pp. 691 ◽  
Author(s):  
Lun ◽  
Ye ◽  
Lin ◽  
Ying ◽  
Wei
Keyword(s):  
Unsteady Flow ◽  
Flow Rate ◽  
Flow Characteristics ◽  
Internal Flow ◽  
Boundary Layer Separation ◽  
Low Flow ◽  
Centrifugal Fan ◽  
Suction Surface ◽  
Cfd Method ◽  
Low Flow Rate

The unsteady flow characteristics of a forward multi-wing centrifugal fan under a low flow rate are studied using the computational fluid dynamics (CFD) method. This paper emphasizes the eddy current distribution in terms of the Q criterion method, as well as pressure fluctuation, frequency spectrum, and kinetic energy spectrum analysis of internal monitoring points in a forward multi-wing centrifugal fan. The numerical results show that abnormal eddies mainly appear at the volute outlet and near the volute tongue, boundary layer separation occurs near the suction surface of the blade, and shedding eddies appear at the trailing edge of the blade with the time evolution. The unsteady flow characteristics of a forward multi-wing centrifugal fan at a small flow rate provide significant physical insight into understanding the internal flow law.

scholarly journals Unsteady Flow Characteristics of Rotating Stall and Surging in a Backward Centrifugal Fan at Low Flow-Rate Conditions

Processes ◽  
2020 ◽  
Vol 8 (7) ◽  
pp. 872 ◽  
Author(s):  
Biao Zhou ◽  
Ximing He ◽  
Hui Yang ◽  
Zuchao Zhu ◽  
Yikun Wei ◽  
...  
Keyword(s):  
Unsteady Flow ◽  
Flow Rate ◽  
Flow Characteristics ◽  
Internal Flow ◽  
Rotating Stall ◽  
Low Flow ◽  
Small Scale ◽  
Centrifugal Fan ◽  
Unsteady Characteristics ◽  
Low Flow Rate

The steady and unsteady flow characteristics of internal flow in a backward centrifugal fan of double inlet at low flow-rate condition are investigated by computational fluid dynamics in this paper. The investigation aims to reveal insights into generation mechanisms and our physical understanding of the rotating stall and surge. The numerical results mainly demonstrate that, with decreasing flow rate, a large number of vortex flows almost increasingly occupy the internal flow of the impeller. The reverse flow and separation vortices increasingly appear near the outlet of volute, and the internal flow of the impeller is completely blocked by the separated vortex flow at low flow-rate conditions. Results indicate that, due to a synchronization of the impeller rotation and separation vortex, these separated vortices act intensely on the pressure surface of the blade with time evolution, and the interaction between the separated vortices and surface of blade increasingly yields small-scale eddies. It is further found that the amplitude of pressure and velocity fluctuations gradually increase with the decrease of flow rate in a certain range. The unsteady characteristics acting on the volute tongue gradually increase in a range of Qd to 0.3 Qd (Qd is the design volume flow rate) with the decrease of flow rate, and the unsteady characteristics acting on the volute tongue are weakened at the working condition of 0.15 Qd. These insights clearly explain the unsteady nature of the rotating stall and surge phenomenon in the double inlet backward centrifugal fan.

scholarly journals Flow Measurement of Oil-Water Two-Phase Flow at Low Flow Rate Using the Plug-in Conductance Sensor Array

Sensors ◽  
2019 ◽  
Vol 19 (21) ◽  
pp. 4649 ◽  
Author(s):  
Jin ◽  
Zhou ◽  
Liang ◽  
Wang ◽  
Zhai ◽  
...  
Keyword(s):  
Flow Rate ◽  
Cross Correlation ◽  
Two Phase Flow ◽  
Low Flow ◽  
Phase Flow ◽  
Two Phase ◽  
Dispersed Oil ◽  
Oil In Water ◽  
Oil Water ◽  
Low Flow Rate

In order to improve the flow measurement accuracy of oil-water two-phase flow at low flow rate, this paper presents a plug-in conductance sensor array (PICSA) for the measurement of water holdup and cross-correlation velocity. Due to the existence of the insert body in PICSA, the effect of slippage and the non-uniform distribution of dispersed phase on the measurement of oil-water two-phase flow at low flow rate can be reduced. The finite element method is used to analyze the electric field distribution characteristics of the plug-in conductance sensor, and the sensor geometry is optimized. The dynamic experiment of oil-water two-phase flow is carried out where water cut Kw and mixture velocity Um are set in the range of 10–98% and 0.0184–0.2580 m/s respectively. Experimental results show that the PICSA has good resolution in water holdup measurement for dispersed oil-in-water slug flow (D OS/W), transition flow (TF), dispersed oil-in-water bubble flow (D O/W) and very fine dispersed oil-in-water bubble flow (VFD O/W). In addition, the cross-correlation velocity of the oil-water two-phase flow is obtained by using the plug-in upstream and downstream conductance sensor arrays. The relationship between the cross-correlation velocity and mixture velocity is found to be sensitive to the change of flow pattern, but it has a good linear relationship under the same flow pattern. Based on the flow pattern identification, a good prediction result of the mixture velocity is obtained using kinematic wave theory. Finally, a high precision prediction of the individual phase volume fraction of oil-water two-phase flow at low flow rate is achieved by using the drift flux model.

scholarly journals Effect of Fins on the Internal Flow Characteristics in the Draft Tube of a Francis Turbine Model

Energies ◽  
2020 ◽  
Vol 13 (11) ◽  
pp. 2806 ◽  
Author(s):  
Seung-Jun Kim ◽  
Young-Seok Choi ◽  
Yong Cho ◽  
Jong-Woong Choi ◽  
Jung-Jae Hyun ◽  
...  
Keyword(s):  
Flow Rate ◽  
Draft Tube ◽  
Pressure Fluctuations ◽  
Flow Characteristics ◽  
Internal Flow ◽  
Low Flow ◽  
Francis Turbine ◽  
Vortex Rope ◽  
Turbine Model ◽  
Low Flow Rate

Undesirable flow phenomena in Francis turbines are caused by pressure fluctuations induced under conditions of low flow rate; the resulting vortex ropes with precession in the draft tube (DT) can degrade performance and increase the instability of turbine operations. To suppress these DT flow instabilities, flow deflectors, grooves, or other structures are often added to the DT into which air or water is injected. This preliminary study investigates the effects of anti-cavity fins on the suppression of vortex ropes in DTs without air injection. Unsteady-state Reynolds-averaged Navier–Stokes analyses were conducted using a scale-adaptive simulation shear stress transport turbulence model to observe the unsteady internal flow and pressure characteristics by applying anti-cavity fins in the DT of a Francis turbine model. A vortex rope with precession was observed in the DT under conditions of low flow rate, and the anti-cavity fins were confirmed to affect the mitigation of the vortex rope. Moreover, at the low flow rate conditions under which the vortex rope developed, the application of anti-cavity fins was confirmed to reduce the maximum unsteady pressure.

scholarly journals Backflow effects on mass flow gain factor in a centrifugal pump

2021 ◽  
Vol 104 (2) ◽  
pp. 003685042199886
Author(s):  
Wenzhe Kang ◽  
Lingjiu Zhou ◽  
Dianhai Liu ◽  
Zhengwei Wang
Keyword(s):  
Centrifugal Pump ◽  
Mass Flow ◽  
Flow Rate ◽  
Low Frequency ◽  
Gain Factor ◽  
Low Flow ◽  
Cavity Volume ◽  
Cavitating Flows ◽  
Inlet Tube ◽  
Low Flow Rate

Previous researches has shown that inlet backflow may occur in a centrifugal pump when running at low-flow-rate conditions and have nonnegligible effects on cavitation behaviors (e.g. mass flow gain factor) and cavitation stability (e.g. cavitation surge). To analyze the influences of backflow in impeller inlet, comparative studies of cavitating flows are carried out for two typical centrifugal pumps. A series of computational fluid dynamics (CFD) simulations were carried out for the cavitating flows in two pumps, based on the RANS (Reynolds-Averaged Naiver-Stokes) solver with the turbulence model of k- ω shear stress transport and homogeneous multiphase model. The cavity volume in Pump A (with less reversed flow in impeller inlet) decreases with the decreasing of flow rate, while the cavity volume in Pump B (with obvious inlet backflow) reach the minimum values at δ = 0.1285 and then increase as the flow rate decreases. For Pump A, the mass flow gain factors are negative and the absolute values increase with the decrease of cavitation number for all calculation conditions. For Pump B, the mass flow gain factors are negative for most conditions but positive for some conditions with low flow rate coefficients and low cavitation numbers, reaching the minimum value at condition of σ = 0.151 for most cases. The development of backflow in impeller inlet is found to be the essential reason for the great differences. For Pump B, the strong shearing between backflow and main flow lead to the cavitation in inlet tube. The cavity volume in the impeller decreases while that in the inlet tube increases with the decreasing of flow rate, which make the total cavity volume reaches the minimum value at δ = 0.1285 and then the mass flow gain factor become positive. Through the transient calculations for cavitating flows in two pumps, low-frequency fluctuations of pressure and flow rate are found in Pump B at some off-designed conditions (e.g. δ = 0.107, σ = 0.195). The relations among inlet pressure, inlet flow rate, cavity volume, and backflow are analyzed in detail to understand the periodic evolution of low-frequency fluctuations. Backflow is found to be the main reason which cause the positive value of mass flow gain factor at low-flow-rate conditions. Through the transient simulations of cavitating flow, backflow is considered as an important aspect closely related to the hydraulic stability of cavitating pumping system.

scholarly journals Effect of Air Injection on the Internal Flow Characteristics in the Draft Tube of a Francis Turbine Model

Processes ◽  
2021 ◽  
Vol 9 (7) ◽  
pp. 1182
Author(s):  
Seung-Jun Kim ◽  
Yong Cho ◽  
Jin-Hyuk Kim
Keyword(s):  
Flow Rate ◽  
Draft Tube ◽  
Pressure Fluctuations ◽  
Flow Characteristics ◽  
Internal Flow ◽  
Air Injection ◽  
Low Flow ◽  
Francis Turbine ◽  
Navier Stokes ◽  
Vortex Rope

Under low flow-rate conditions, a Francis turbine exhibits precession of a vortex rope with pressure fluctuations in the draft tube. These undesirable flow phenomena can lead to deterioration of the turbine performance as manifested by torque and power output fluctuations. In order to suppress the rope with precession and a swirl component in the tube, the use of anti-swirl fins was investigated in a previous study. However, vortex rope generation still occurred near the cone of the tube. In this study, unsteady-state Reynolds-averaged Navier–Stokes analyses were conducted with a scale-adaptive simulation shear stress transport turbulence model. This model was used to observe the effects of the injection in the draft tube on the unsteady internal flow and pressure phenomena considering both active and passive suppression methods. The air injection affected the generation and suppression of the vortex rope and swirl component depending on the flow rate of the air. In addition, an injection level of 0.5%Q led to a reduction in the maximum unsteady pressure characteristics.

A Meanline Model for Impeller Flow Recirculation

2008 ◽  
Author(s):  
Xuwen Qiu ◽  
David Japikse ◽  
Mark Anderson
Keyword(s):  
Flow Rate ◽  
Recirculation Zone ◽  
Reverse Flow ◽  
Low Flow ◽  
Suction Surface ◽  
Blade Loading ◽  
Flow Recirculation ◽  
Impeller Outlet ◽  
Active Flow ◽  
Low Flow Rate

Flow recirculation at the impeller inlet and outlet is an important feature that affects impeller performance, especially the power consumption at a very low flow rate. Although the mechanisms for this flow phenomenon have been studied, a practical model is needed for meanline modeling of impeller off-design performance. In this paper, a meanline recirculation model is proposed. At the inlet, the recirculation zone acts as area blockage to relieve the large incidence of the active flow at a low flow rate. The size of the blockage is estimated through a critical area ratio of an artificial “inlet diffuser” from the inlet to throat. The intensity of the reverse flow can then be calculated by assuming a linear velocity profile of meridional velocity in the recirculation zone. At the impeller outlet, a recirculation zone near the suction surface is established to balance the velocity difference on the pressure and suction sides of the blade. The size and the intensity of the outlet recirculation zone is assumed related to blade loading, which can be evaluated based on flow turning and Coriolis force. A few validation cases are presented showing a good comparison between test data and prediction by the model.

Experimental Investigation of Surge Phenomena in a Transonic Centrifugal Compressor With Inlet Distortion

2020 ◽  
Author(s):  
Sasuga Ito ◽  
Masato Furukawa ◽  
Satoshi Gunjishima ◽  
Takafumi Ota ◽  
Kazuhito Konishi ◽  
...  
Keyword(s):  
Flow Rate ◽  
Centrifugal Compressor ◽  
Flow Instability ◽  
Pressure Sensors ◽  
Low Flow ◽  
Inlet Distortion ◽  
Transonic Centrifugal Compressor ◽  
Response Pressure ◽  
Surge Phenomena ◽  
Low Flow Rate

Abstract Inlet distortion has influence on the aerodynamic performance of turbomachinery such as compressors, turbines and fans. On turbochargers, bent pipes are installed around the compressor due to the spatial limitations in the engine room of the vehicle. As the result, the compressor is operated with the distorted inflow. In the low flow rate operation, the distorted inflow also affects the flow instability like stall and surge. Especially, the operation range on the low flow rate side is defined based on the flow rate where surge occurs, so it is important to investigate the effect of the distorted inflow on surge. In this study, the effect of the inlet distortion to surge phenomena has been investigated by the experiments with a transonic centrifugal compressor. A bent pipe has been installed at the upstream of the compressor to generate a distorted flow. Experiments have been also conducted under the condition that a straight pipe was installed upstream of the compressor, and unsteady measurements with high response pressure sensors and an I-type hot wire probe have been carried out to each experiments. In addition, Fast Fourier transform (FFT) and Wavelet transform have been applied to the unsteady measurement results obtained from each experiment.

scholarly journals A Comparative Assessment of Spalart-Shur Rotation/Curvature Correction in RANS Simulations in a Centrifugal Pump Impeller

2014 ◽  
Vol 2014 ◽  
pp. 1-9 ◽  
Author(s):  
Ran Tao ◽  
Ruofu Xiao ◽  
Wei Yang ◽  
Fujun Wang
Keyword(s):  
Kinetic Energy ◽  
Centrifugal Pump ◽  
Flow Rate ◽  
Comparative Assessment ◽  
Turbulence Kinetic Energy ◽  
Low Flow ◽  
Pump Impeller ◽  
Curvature Correction ◽  
Centrifugal Pump Impeller ◽  
Low Flow Rate

RANS simulation is widely used in the flow prediction of centrifugal pumps. Influenced by impeller rotation and streamline curvature, the eddy viscosity models with turbulence isotropy assumption are not accurate enough. In this study, Spalart-Shur rotation/curvature correction was applied on the SSTk-ωturbulence model. The comparative assessment of the correction was proceeded in the simulations of a centrifugal pump impeller. CFD results were compared with existing PIV and LDV data under the design and low flow rate off-design conditions. Results show the improvements of the simulation especially in the situation that turbulence strongly produced due to undesirable flow structures. Under the design condition, more reasonable turbulence kinetic energy contour was captured after correction. Under the low flow rate off-design condition, the prediction of turbulence kinetic energy and velocity distributions became much more accurate when using the corrected model. So, the rotation/curvature correction was proved effective in this study. And, it is also proved acceptable and recommended to use in the engineering simulations of centrifugal pump impellers.

Sign in / Sign up

Export Citation Format

Share Document