Buildings on the Slope Considering Effects of Uneven Settlement of Single Pile on the Structure Research

2011 ◽  
Vol 368-373 ◽  
pp. 1949-1954
Author(s):  
Li Ming Wu ◽  
Zi Jian Wang
Keyword(s):  
Finite Element Analysis ◽  
Pile Foundation ◽  
Normal Load ◽  
Single Pile ◽  
Analysis Software ◽  
Load Bearing Capacity ◽  
Element Analysis ◽  
Structural Impact ◽  
Different Parts ◽  
Structure Research

Buildings built on the slope and slope, in order to avoid a lot of digging embankment. According to the slope of potential changes in pile foundation of General unequal height. In the design of such buildings are generally the superstructure and Foundation when considered separately, under normal load bearing capacity and deformation is to meet to coordinal requirements.Changes in water level cause of slope sliding, so lead to individual settlement, the class meets the deformation of the structure of coordination of the Department of architecture and how the force is not known. Based on this, to a shore in 8 layers of pile foundation in the framework, for example, using finite element analysis software ANSYS in different parts of a single settlement on the basis of structural impact.

Design Research of Steel Pipe Combination of Angle Steel Tower of XiYue 220kV Cross Section

2013 ◽  
Vol 470 ◽  
pp. 408-411 ◽  
Author(s):  
Yan Zhong Ju ◽  
Xiao Xu Fu ◽  
Neng Xian Zeng
Keyword(s):  
Finite Element Analysis ◽  
Cross Section ◽  
Design Research ◽  
Axial Stress ◽  
Steel Pipe ◽  
Stress Difference ◽  
Analysis Software ◽  
Element Analysis ◽  
The Finite Element Analysis ◽  
Angle Steel

Given the path situation of Xiyue substation 220kV four outlets project crossing Shunde waterway section,this article applies of Dao Heng tower full stress analysis software and the finite element analysis software ANSYS to two steel pipe combination of angle steel towers to carry on design research,contrast axial stress of two kinds of software,analyse the reasons of axial stress difference.

ANSYS Simply Supported Deep Beams Based on the Study of Mechanical Properties

2013 ◽  
Vol 351-352 ◽  
pp. 782-785
Author(s):  
Yong Bing Liu ◽  
Xiao Zhong Zhang
Keyword(s):  
Mechanical Properties ◽  
Finite Element Analysis ◽  
Mechanical Model ◽  
Work Performance ◽  
Deep Beam ◽  
Analysis Software ◽  
Deep Beams ◽  
Element Analysis ◽  
Simply Supported ◽  
Force Characteristics

Established the mechanical model of simply supported deep beam, calculation and analysis of simple supported deep beams by using finite element analysis software ANSYS, simulated the force characteristics and work performance of the deep beam. Provides the reference for the design and construction of deep beams.

Finite Element Analysis and Optimization of the Truss of Installing Wave-Maker Based on ANSYS

2013 ◽  
Vol 313-314 ◽  
pp. 1038-1041
Author(s):  
Shou Jun Wang ◽  
Xing Xiong ◽  
Chao Li
Keyword(s):  
Finite Element Analysis ◽  
Finite Element ◽  
Design Parameters ◽  
Analysis Software ◽  
Element Analysis ◽  
Large Span ◽  
The Finite Element Analysis ◽  
Wave Maker

According to uncertainty of the design parameters for large span truss of installing wave-maker, in order to avoid the waste of materials,the truss is analyzed based on the finite element analysis software ANSYS to find out its weaknesses and various parts of the deformation. On the premise of ensuring the intensity and stiffness, the weight of the truss is reduced by adjusting its sizes and selecting different profiles, so as to achieve the optimization of the truss of installing wave-maker.

Experimental Research on the Magnetic Field Sensitive Polymeric Actuator

2011 ◽  
Vol 287-290 ◽  
pp. 603-607
Author(s):  
Chun Lin Xia ◽  
Yang Fang Wu ◽  
Qian Qian Lu
Keyword(s):  
Magnetic Field ◽  
Finite Element Analysis ◽  
Finite Element ◽  
Energy Conversion ◽  
Experimental Research ◽  
Experimental Results ◽  
Deformation Characteristics ◽  
Analysis Software ◽  
Element Analysis ◽  
The Magnetic Field

Using domestic MFSP membrane as a medium of energy conversion, a kind of MFSP actuator was designed. The dedicated test equipment was constructed for experimental research, and the experimental results were given. The strip and circular MSFP membrane were analyzed qualitatively to obtain the deformation characteristics of membrane by finite element analysis software.

CAD/CAE on the Mould Plates of Vertical Type High-Pressure Grouting Machine

2012 ◽  
Vol 538-541 ◽  
pp. 2681-2684
Author(s):  
Zhi Cheng Huang
Keyword(s):  
Finite Element Analysis ◽  
Finite Element ◽  
High Pressure ◽  
3D Model ◽  
Stress And Strain ◽  
Analysis Software ◽  
Element Analysis ◽  
Pressure Grouting ◽  
Object Of Study

Took a type of ceramics for daily use vertical type high pressure grouting machine as the object of study, study the stress and strain of its upper and lower mould plates. Established their 3D model by CAD software Pro-E, and then import them into finite element analysis software to analysis the value and distribution of the stress and strain. The analysis results can provide some reference for design, and have some engineering and practical value.

Effect of Strain Rate on the Simulation of MEMS Safety and Arming Device

2014 ◽  
Vol 609-610 ◽  
pp. 849-855
Author(s):  
Wen Rui Ma ◽  
Guang He
Keyword(s):  
Finite Element Analysis ◽  
Strain Rate ◽  
Impact Load ◽  
Simulation Models ◽  
Strain Rate Effect ◽  
Rate Effect ◽  
Experimental Results ◽  
Analysis Software ◽  
Element Analysis ◽  
Simulation Results

Under launch impact load, LIGA nickel that manufacturing MEMS fuze safety and arming (S&A) device will have obvious strain rate effect. By using finite element analysis software ANSYS/LS-DYNA, simulation models of a small-caliber ammunition MEMS fuze setback S&A device with strain rate effect and without strain rate effect were respectively established. The results of the two simulation modules were quite different. Comparisons between experimental results and simulation results show that simulation results considering strain rate effect agree well with experimental results, which proves strain rate effect should not be ignored in the simulation of MEMS S&A device.

Sign in / Sign up

Export Citation Format

Share Document