Extraction of Bamboo Nanofibers Using Acid Hydrolysis for Functional Chemicals of Ecological Dyeing and Finishing

2012 ◽  
Vol 441 ◽  
pp. 759-763 ◽  
Author(s):  
Yong Zhang ◽  
Guo Xin Xue ◽  
Xiu Mei Zhang ◽  
Yan Jun Tang
Keyword(s):  
Acid Hydrolysis ◽  
Cellulose Nanofibers ◽  
Average Diameter ◽  
Degree Of Polymerization ◽  
X Ray Diffraction ◽  
Surface Charges ◽  
Aggregation State ◽  
Transmission Electron ◽  
Different Types ◽  
Bamboo Fibers

In this work a study on the feasibility of extracting cellulose nanofibers from bamboo fibers, by means of three different procedures was carried out. These processes included the using of three different types of acids (H2SO4, HCl, and a mixture of H2SO4/HCl). The raw bamboo fibers were mercerized with NaOH solutions. They were then submitted to the three different acid hydrolysis processes. The final bamboo nanofibers were morphologically characterized by transmission electron microscopy (TEM) and their surface charges in suspensions were estimated by Zeta-potential. Their degree of polymerization (DP) was characterized by viscometry and the crystallinity was tested by X-ray diffraction (XRD). All bamboo nanofibers presented a rod-like shape, an average diameter (D) of 6-10 nm and length (L) of 100-180 nm, with an aspect ratio (L/D) of around 16-18. The aggregation state increases with the amount of HCl introduced into the extraction, due to the decrease of surface charges. However, this release presented nanofibers with litter better degree of polymerization than those whose acid hydrolysis was carried out using only H2SO4.

Preparation of Novel Ag/Bacterial Cellulose Hybrid Nanofibers for Antimicrobial Wound Dressing

2010 ◽  
Vol 152-153 ◽  
pp. 1771-1774 ◽  
Author(s):  
Jia Zhi Yang ◽  
Ju Wei Yu ◽  
Dong Ping Sun ◽  
Xu Jie Yang
Keyword(s):  
Bacterial Cellulose ◽  
Ag Nanoparticles ◽  
Antimicrobial Agents ◽  
Chemical Reduction ◽  
Cellulose Nanofibers ◽  
Analytical Techniques ◽  
Average Diameter ◽  
X Ray Diffraction ◽  
Hybrid Nanofibers ◽  
Transmission Electron

In this work, we describe a novel facile method to prepare long one-dimensional hybrid nanofibers by using hydrated bacterial cellulose nanofibers (BCF) as template. Silver (Ag) nanoparticles with an average diameter of 1.5 nm were well dispersed on BC nanofibers via a simple in situ chemical-reduction between AgNO3 and NaBH4 at relatively low temperature. The bare BCF and as-prepared Ag/BCF hybrid nanofibers were characterized by a range of analytical techniques including transmission electron microscopy (TEM), X-ray diffraction (XRD), and UV–vis absorption spectra (UV–vis). The results reveal that Ag nanoparticles were homogeneously precipitated on the BCF surface. The results indicate that Ag/BCF hybrid nanofibers are promising candidate materials for functional antimicrobial agents.

scholarly journals Isolation and Characterization of Cellulose Nanofibers fromGigantochloa scortechiniias a Reinforcement Material

2016 ◽  
Vol 2016 ◽  
pp. 1-8 ◽  
Author(s):  
Chaturbhuj K. Saurabh ◽  
Asniza Mustapha ◽  
M. Mohd. Masri ◽  
A. F. Owolabi ◽  
M. I. Syakir ◽  
...  
Keyword(s):  
Electron Microscopy ◽  
Cellulose Nanofibers ◽  
X Ray Diffraction ◽  
X Ray ◽  
Isolation And Characterization ◽  
Transmission Electron ◽  
Reinforcement Material ◽  
Bamboo Fibers ◽  
Ft Ir

Cellulose nanofibers (CNF) were isolated fromGigantochloa scortechiniibamboo fibers using sulphuric acid hydrolysis. This method was compared with pulping and bleaching process for bamboo fiber. Scanning electron microscopy, transmission electron microscopy, Fourier transform infrared spectroscopy, X-ray diffraction, and thermogravimetric analysis were used to determine the properties of CNF. Structural analysis by FT-IR showed that lignin and hemicelluloses were effectively removed from pulp, bleached fibers, and CNF. It was found that CNF exhibited uniform and smooth morphological structures, with fiber diameter ranges from 5 to 10 nm. The percentage of crystallinity was significantly increased from raw fibers to cellulose nanofibers, microfibrillated, along with significant improvement in thermal stability. Further, obtained CNF were used as reinforcement material in epoxy based nanocomposites where tensile strength, flexural strength, and modulus of nanocomposites improved with the addition of CNF loading concentration ranges from 0 to 0.7%.

Effect of Acid/Fiber Ratio on Physical Properties of Cellulose Nanofibers Extracted from Cassava Pulp

2017 ◽  
Vol 890 ◽  
pp. 103-107
Author(s):  
Thanh Chi Nguyen ◽  
Ruksakulpiwat Chaiwat ◽  
Yupaporn Ruksakulpiwat
Keyword(s):  
Thermal Stability ◽  
Physical Properties ◽  
Acid Hydrolysis ◽  
Cellulose Nanofibers ◽  
X Ray Diffraction ◽  
Cassava Pulp ◽  
Transmission Electron ◽  
Naoh Solution ◽  
Bleaching Treatment ◽  
Thermal Stability Of

Cellulose nanofibers (CeNF) were extracted successfully from cassava pulp (CP) by submitting to alkali, bleaching and acid hydrolysis treatments. The raw CP was mercerized with NaOH solution and then followed by bleaching treatment using a solution made up of equal parts (v:v) of acetate buffer and aqueous chlorite. In order to obtain cellulose nanofibers, the acid hydrolysis treatment of bleached fibers was performed using a mixture of HCl/H2SO4 (1:2 v/v). In this acid treatment reaction, the effects of acid/fiber ratio (ml/g) on physical properties of obtained cellulose nanofibers were investigated. Nanofibers were morphologically characterized by transmission electron microscopy (TEM) revealing the nanofibers with diameter in the range of 12-24 nm and immeasurable length were obtained. An increase in crystallinity of fibers after treatments was revealed by X-ray diffraction (XRD). Due to the introduction of sulfate groups at the outer surfaces of fibers during the hydrolysis, thermal stability of nanofibers, characterized by thermogravimetric analysis (TGA), was lower than that of raw CP. The acid/fiber ratio of 150ml/2g was found to be a proper ratio for thermal stability of obtained nanofibers. The crystallinity of nanofibers increased with the increase of acid/fiber ratio.

Enzymatic Preparation of Nanocrystalline Cellulose from Bamboo Fibers

2012 ◽  
Vol 441 ◽  
pp. 754-758 ◽  
Author(s):  
Yong Zhang ◽  
Guo Xin Xue ◽  
Xiu Mei Zhang ◽  
Yu Zhao
Keyword(s):  
Enzymatic Hydrolysis ◽  
Average Diameter ◽  
Degree Of Polymerization ◽  
Nanocrystalline Cellulose ◽  
Preparation Process ◽  
Enzymatic Preparation ◽  
Bamboo Pulp ◽  
Transmission Electron ◽  
Hydrolysis Process ◽  
Bamboo Fibers

This paper reports an attempt to prepare nanocrystalline cellulose from bamboo fibers through an enzymatic hydrolysis process. A type of commercial cellulase, viz. enzyme Cclast (mainly containing endoglucanase) was used in the preparation process. The morphology of the prepared bamboo cellulose nanocrystals was characterized by transmission electron microscopy (TEM) and the sugar analyses of hydrolysis residues were analyzed by ion chromatography (IC). The degree of polymerization (DP) was tested by automatic viscosimeter. All nanocrystalline cellulose from bamboo fibers presented a rod-like shape, an average diameter (D) of 5.3 nm and length (L) of 221 nm, with an aspect ratio (L/D) of around 42. It was shown that the use of enzymatic hydrolysis treatment to bleach bamboo pulp helps the preparation of well individualized rod-like nanocrystalline cellulose.

Physical and Mechanical Characterization of Polyvinyl Alcohol Nanocomposite Made from Cellulose Nanofibers

2020 ◽  
Vol 988 ◽  
pp. 65-72
Author(s):  
Ferriawan Yudhanto ◽  
Jamasri ◽  
Heru Santoso Budi Rochardjo
Keyword(s):  
Polyvinyl Alcohol ◽  
Acid Hydrolysis ◽  
Nanocomposite Film ◽  
Cellulose Nanofibers ◽  
X Ray Diffraction ◽  
Casting Technique ◽  
Hydrolysis Method ◽  
Transmission Electron ◽  
Solution Casting Technique ◽  
Mixing Method

A method using a combination of acid hydrolysis and ultrasonic homogenize were developed to obtain the CNF (cellulose nanofibers) from agave cantala fibers. Acid hydrolysis method able to produce the CNF with a diameter around of 45-50 nm, which can investigated by transmission electron microscopy (TEM). The homogenize mixing method between CNF 5 wt% colloidal and 3 wt% PVA (polyvinyl alcohol) with magnetic stirrer 350 RPM, at temperature of 50 °C, for 30 minutes followed by ultrasonic homogenizer has been causing CNF well distributed in the PVA matrix. PVA/CNF nanocomposites film was prepared by solution casting technique. Physical properties test by x-ray diffraction (XRD) and fourier transform infrared (FTIR) shows highly crystalline of CNF which indicates improvements the mechanical properties of PVA/CNF nanocomposite film. The tensile stress and elongation at break of PVA/CNF nanocomposite film were increased by 55 % and 137 %.

Monodisperse Fe3O4/Fe Core/Shell Nanoparticles with Enhanced Magnetic Property

2011 ◽  
Vol 306-307 ◽  
pp. 410-415
Author(s):  
Li Sun ◽  
Fu Tian Liu ◽  
Qi Hui Jiang ◽  
Xiu Xiu Chen ◽  
Ping Yang
Keyword(s):  
Average Diameter ◽  
Chemical Precipitation ◽  
Precipitation Method ◽  
Core Shell ◽  
X Ray Diffraction ◽  
Shell Nanoparticles ◽  
X Ray ◽  
Transmission Electron ◽  
Shell Particles ◽  
Core Shell Nanoparticles

Core/shell type nanoparticles with an average diameter of 20nm were synthesized by chemical precipitation method. Firstly, Monodisperse Fe3O4 nanoparticles were synthesized by solvethermal method. FeSO4ž7H2O and NaBH4 were respectively dissolved in distilled water, then moderated Fe3O4 particles and surfactant(PVP) were ultrasonic dispersed into the FeSO4ž7H2O solution. The resulting solution was stirred 2 h at room temperature. Fe could be deposited on the surface of monodispersed Fe3O4 nanoparticles to form core-shell particles. The particles were characterized by using various experimental techniques, such as transmission electron microscopy (TEM), X-ray diffraction (XRD), AGM and DTA. The results suggest that the saturation magnetization of the nanocomposites is 100 emu/g. The composition of the samples show monodisperse and the sides of the core/shell nanoparticles are 20-30nm. It is noted that the formation of Fe3O4/Fe nanocomposites magnetite nanoparticles possess superparamagnetic property.

Sb-rich nanoinclusions in an AlGaAsSb metamaterial

MRS Advances ◽  
2019 ◽  
Vol 4 (5-6) ◽  
pp. 277-284
Author(s):  
Nikolay A. Bert ◽  
Vladimir V. Chaldyshev ◽  
Nikolay A. Cherkashin ◽  
Vladimir N. Nevedomskiy ◽  
Valery V. Preobrazhenskii ◽  
...  
Keyword(s):  
Molecular Beam ◽  
Filling Factor ◽  
Local Thermodynamic Equilibrium ◽  
Average Diameter ◽  
Formation Temperature ◽  
X Ray Diffraction ◽  
X Ray ◽  
Self Organized ◽  
Transmission Electron ◽  
The Matrix

ABSTRACTWe studied the microstructure of Al0.28Ga0.72As0.972Sb0.028 metamaterials containing a developed array of AsSb nanoinclusions. The AlGaAsSb films were grown by low-temperature molecular-beam epitaxy followed by high-temperature annealing at 750°C. The process resulted in an array of self-organized AsSb nanonclusions with an average diameter of 15 nm. The volume filling factor was about 0.003. Using transmission electron microscopy and x-ray diffraction we showed that the nanoinclusions have A7-type rhombohedral atomic structure with the following orientation in the matrix (0003)p || {111}m and [-2110]p || 〈220〉m, where p and m indices indicate the AsSb precipitate and AlGaAsSb matrix, correspondingly. The nanoinclusions appeared to be strongly enriched by antimony (more than 90 atomic %), whereas the Sb content in the AlGaAsSb matrix was 2.8 atomic %. The strong enrichment of the inclusion with Sb resulted from the local thermodynamic equilibrium between the solid AlGaAsSb matrix and AsSb inclusions which became liquid at a formation temperature of 750°C.

Synthesis of Carbon Nanosphere at Low Temperatures Based on Bamboo Fiber

2019 ◽  
Vol 966 ◽  
pp. 163-168 ◽  
Author(s):  
Yulia Kirana Lahsmin ◽  
Dahlang Tahir ◽  
Bualkar Abdullah ◽  
Sultan Ilyas ◽  
Inayatul Mutmainna
Keyword(s):  
Electron Microscopy ◽  
Transmission Electron Microscopy ◽  
Low Temperatures ◽  
Potassium Hydroxide ◽  
Bamboo Fiber ◽  
X Ray Diffraction ◽  
Activation Temperature ◽  
X Ray ◽  
Transmission Electron ◽  
Bamboo Fibers

Carbon Nanosphere (CNs) has been successfully synthesized from bamboo fibers at low temperatures by carbonization and activation. For activation used Potassium Hydroxide (KOH) at temperature 105°C, 155°C, 205°C, 255°C and 305°C. X-Ray Diffraction (XRD) spectra shows hexagonal and amorphous phase and Fourier Transform Infrared (FTIR) spectra shows decrease C-O bond with increasing activation temperature. Transmission Electron Microscopy (TEM) image for activation temperature of 105°C confirmed that sources the formation of Carbon Nanosphere. In this study shows bamboo fiber has a high potential as a carbon nanosphere material.

scholarly journals Effects of Size and Dispersity of Microcrystalline Celluloses on Size, Structure and Stability of Nanocrystalline Celluloses Extracted by Acid Hydrolysis

Nano LIFE ◽  
2014 ◽  
Vol 04 (04) ◽  
pp. 1441014 ◽  
Author(s):  
Qi Liu ◽  
Weiping Hao ◽  
Yongguang Yang ◽  
Aurore Richel ◽  
Canbin Ouyang ◽  
...  
Keyword(s):  
Particle Size ◽  
Acid Hydrolysis ◽  
Size Structure ◽  
Particle Sizes ◽  
X Ray Diffraction ◽  
X Ray ◽  
Force Microscopy ◽  
Atomic Force ◽  
Transmission Electron ◽  
Sonication Treatment

Nanocrystalline celluloses (NCCs) were separated from four commercial microcrystalline celluloses (MCCs) by an acid hydrolysis–sonication treatment. Transmission electron microscopy (TEM), atomic force microscopy (AFM), Fourier transform infrared (FTIR) spectrum, X-ray diffraction (XRD) and thermogravimetric analysis (TGA) were conducted to investigate the NCCs. MCCs with different morphologies and particle sizes showed different aggregation degrees. The aggregation of MCCs followed the order MCC1 > MCC3 > MCC2 > MCC4, which is the same order of the heights of the resulting NCCs. The best uniformity and thermal stability were characterized for NCC3, which was produced by MCC3 with smallest original particle size and good dispersity among the four MCCs. This result suggests that both the original particle size and dispersity of MCCs had significant effects on separated NCCs.

Synthesis and upconversion luminescence properties of CaF2:Yb3+,Er3+ nanoparticles obtained from SBA-15 template

2010 ◽  
Vol 25 (10) ◽  
pp. 2035-2041 ◽  
Author(s):  
Zhiguo Xia ◽  
Peng Du
Keyword(s):  
Electron Microscopy ◽  
Upconversion Luminescence ◽  
Emission Spectra ◽  
Average Diameter ◽  
Cubic Phase ◽  
Pumping Power ◽  
X Ray Diffraction ◽  
Temperature Dependent ◽  
X Ray ◽  
Transmission Electron

CaF2:Yb3+,Er3+ upconversion (UC) luminescence nanoparticles have been synthesized using mesoporous silica (SBA-15) as a hard template. The samples were characterized by x-ray diffraction, Fourier transform infrared spectra, field-emission scanning electron microscopy, transmission electron microscopy, and UC emission spectra, respectively. Highly crystalline cubic phase CaF2:Yb3+,Er3+ nanoparticles are uniformly distributed with an average diameter of about 40–50 nm, and the formation process is also demonstrated. The UC fluorescence has been realized in the as-prepared CaF2:Yb3+,Er3+ nanoparticles on 980-nm excitation. The UC emission transitions for 4F9/2–4I15/2 (red), 2H11/2–4I15/2 (green), 4S3/2–4I15/2 (green), and 2H9/2–4I15/2 (violet) in the Yb3+/Er3+ codoped CaF2 nanoparticles depending on pumping power and temperature have been discussed. The UC mechanism, especially the origin on the temperature-dependent UC emission intensities ratio between 2H11/2 and 4S3/2 levels, have been proposed.

Sign in / Sign up

Export Citation Format

Share Document