The Effect of Strain Rate on the Tensile Behavior of Electrodeposited Nanocrystalline Ni-Co Alloy

2012 ◽  
Vol 535-537 ◽  
pp. 353-356
Author(s):  
Li Yuan Qin ◽  
Jian She Lian ◽  
Long Zhe Quan ◽  
En Chen Jiang
Keyword(s):  
Strain Rate ◽  
Room Temperature ◽  
Mechanical Performance ◽  
Rate Sensitivity ◽  
High Strength ◽  
Solid Solution Hardening ◽  
Strain Rates ◽  
Mechanism Transition ◽  
Surface Morphologies ◽  
High Strain Rate Sensitivity

A fully dense nanocrystalline Ni-Co alloy with 18 nm grain size exhibited high strength of about 2200 MPa and ductility of 8.19.2% at strain rates of 1.04×10-5 to 1.04 s-1 and room temperature. The alloying of Co element induces the grain refinement, solid solution hardening and decrease of stacking fault energy should contribute to the favorable combination of mechanical performance. The obvious distinctions of fracture-surface morphologies with strain rate alteration were attributed to underlying deformation mechanism transition. The high strain rate sensitivity exponent and small activation volume indicate that grain boundary activity may be expected in this alloy.

The effects of strain and strain rate on residual microstructures in copper

1986 ◽  
Vol 44 ◽  
pp. 420-421
Author(s):  
M. F. Stevens ◽  
P. S. Follansbee
Keyword(s):  
Strain Rate ◽  
Applied Stress ◽  
Threshold Stress ◽  
Rate Sensitivity ◽  
Viscous Drag ◽  
Strain Rates ◽  
Strain And Strain Rate ◽  
Threshold Strength ◽  
Mechanism Transition ◽  
Intrinsic Strength

The strain rate sensitivity of a variety of materials is known to increase rapidly at strain rates exceeding ∼103 sec-1. This transition has most often in the past been attributed to a transition from thermally activated guide to viscous drag control. An important condition for imposition of dislocation drag effects is that the applied stress, σ, must be on the order of or greater than the threshold stress, which is the flow stress at OK. From Fig. 1, it can be seen for OFE Cu that the ratio of the applied stress to threshold stress remains constant even at strain rates as high as 104 sec-1 suggesting that there is not a mechanism transition but that the intrinsic strength is increasing, since the threshold strength is a mechanical measure of intrinsic strength. These measurements were made at constant strain levels of 0.2, wnich is not a guarantee of constant microstructure. The increase in threshold stress at higher strain rates is a strong indication that the microstructural evolution is a function of strain rate and that the dependence becomes stronger at high strain rates.

Local Investigations of the Mechanical Properties of Ultrafine Grained Metals by Nanoindentations

2006 ◽  
Vol 503-504 ◽  
pp. 31-36 ◽  
Author(s):  
Johannes Mueller ◽  
Karsten Durst ◽  
Dorothea Amberger ◽  
Matthias Göken
Keyword(s):  
Mechanical Properties ◽  
Strain Rate ◽  
Strain Rate Sensitivity ◽  
Room Temperature ◽  
Rate Sensitivity ◽  
Strain Rates ◽  
Fcc Metals ◽  
Angular Pressing ◽  
Ultrafine Grained ◽  
Indentation Strain

The mechanical properties of ultrafine-grained metals processed by equal channel angular pressing is investigated by nanoindentations in comparison with measurements on nanocrystalline nickel with a grain size between 20 and 400 nm produced by pulsed electrodeposition. Besides hardness and Young’s modulus measurements, the nanoindentation method allows also controlled experiments on the strain rate sensitivity, which are discussed in detail in this paper. Nanoindentation measurements can be performed at indentation strain rates between 10-3 s-1 and 0.1 s-1. Nanocrystalline and ultrafine-grained fcc metals as Al and Ni show a significant strain rate sensitivity at room temperature in comparison with conventional grain sized materials. In ultrafine-grained bcc Fe the strain rate sensitivity does not change significantly after severe plastic deformation. Inelastic effects are found during repeated unloading-loading experiments in nanoindentations.

Strain-Rate Effect on the Tensile Behaviour of High Strength Alloys

2011 ◽  
Vol 82 ◽  
pp. 124-129 ◽  
Author(s):  
Ezio Cadoni ◽  
Matteo Dotta ◽  
Daniele Forni ◽  
Stefano Bianchi
Keyword(s):  
Strain Rate ◽  
Rate Sensitivity ◽  
High Strength ◽  
Constitutive Law ◽  
Tensile Behaviour ◽  
Strain Rates ◽  
Cross Sectional ◽  
Split Hopkinson Tensile Bar ◽  
Wide Range ◽  
First Results

In this paper the first results of the mechanical characterization in tension of two high strength alloys in a wide range of strain rates are presented. Different experimental techniques were used for different strain rates: a universal machine, a Hydro-Pneumatic Machine and a JRC-Split Hopkinson Tensile Bar. The experimental research was developed in the DynaMat laboratory of the University of Applied Sciences of Southern Switzerland. An increase of the stress at a given strain increasing the strain-rate from 10-3 to 103 s-1, a moderate strain-rate sensitivity of the uniform and fracture strain, a poor reduction of the cross-sectional area at fracture with increasing the strain-rate were shown. Based on these experimental results the parameters required by the Johnson-Cook constitutive law were determined.

Strain rate sensitivity of a mild steel at room temperature and strain rates of up to 105s−1

1980 ◽  
Vol 15 (4) ◽  
pp. 201-207 ◽  
Author(s):  
M S J Hashmi
Keyword(s):  
Finite Difference ◽  
Mild Steel ◽  
Strain Rate ◽  
Strain Hardening ◽  
Strain Rate Sensitivity ◽  
Elastic Strain ◽  
Room Temperature ◽  
Numerical Technique ◽  
Rate Sensitivity ◽  
Strain Rates

Experimental results on a mild steel are reported from ballistics tests which gave rise to strain rates of up to 105 s−1. A finite-difference numerical technique which incorporates material inertia, elastic-strain hardening and strain-rate sensitivity is used to establish the strain-rate sensitivity constants p and D in the equation, σ4 = σ1 (1+(∊/D)1/ p). The rate sensitivity established in this study is compared with those reported by other researchers.

Strain-Rate Sensitivity Enhanced by Grain-Boundary Sliding in Creep Condition for AZ31 Magnesium Alloy at Room Temperature

2016 ◽  
Vol 838-839 ◽  
pp. 106-109 ◽  
Author(s):  
Tetsuya Matsunaga ◽  
Hidetoshi Somekawa ◽  
Hiromichi Hongo ◽  
Masaaki Tabuchi
Keyword(s):  
Grain Boundary ◽  
Strain Rate ◽  
Strain Rate Sensitivity ◽  
Room Temperature ◽  
High Strain ◽  
Rate Sensitivity ◽  
Grain Boundary Sliding ◽  
Strain Rates ◽  
High Strain Rates ◽  
Boundary Sliding

This study investigated strain-rate sensitivity (SRS) in an as-extruded AZ31 magnesium (Mg) alloy with grain size of about 10 mm. Although the alloy shows negligible SRS at strain rates of >10-5 s-1 at room temperature, the exponent increased by one order from 0.008 to 0.06 with decrease of the strain rate down to 10-8 s-1. The activation volume (V) was evaluated as approximately 100b3 at high strain rates and as about 15b3 at low strain rates (where b is the Burgers vector). In addition, deformation twin was observed only at high strain rates. Because the twin nucleates at the grain boundary, stress concentration is necessary to be accommodated by dislocation absorption into the grain boundary at low strain rates. Extrinsic grain boundary dislocations move and engender grain boundary sliding (GBS) with low thermal assistance. Therefore, GBS enhances and engenders SRS in AZ31 Mg alloy at room temperature.

The Effect of Strain Rate on Yielding in High Strength Steels

1966 ◽  
Vol 88 (1) ◽  
pp. 37-44 ◽  
Author(s):  
D. P. Kendall ◽  
T. E. Davidson
Keyword(s):  
Strain Rate ◽  
Strain Rate Sensitivity ◽  
Power Law ◽  
High Strength Steels ◽  
Rate Sensitivity ◽  
High Strength ◽  
Strain Rates ◽  
Alloy Steels ◽  
Strength Alloy ◽  
Continuous Power

The effect of strain rates ranging from 10−4 to 10 in/in/sec on the yield strengths of several high strength alloy steels is investigated. Quenched and tempered-type alloys exhibit two regions of strain-rate sensitivity with the strain rate dividing the sensitive and insensitive regions varying from 0.5 to greater than 10 in/in/sec, depending on composition, microstructure and grain size. At the higher rates a power-law relationship is found which is consistent with a yielding model involving breakaway of dislocations from solute atmospheres. Maraging steel exhibits a continuous power law-strain rate sensitivity over the entire range.

IMPROVED MECHANICAL PROPERTY OF ELECTRODEPOSITED NANOCRYSTALLINE NICKEL-COBALT ALLOY

2010 ◽  
Vol 24 (15n16) ◽  
pp. 2285-2290 ◽  
Author(s):  
XIXUN SHEN ◽  
JIANSHE LIAN
Keyword(s):  
Strain Rate ◽  
High Strain ◽  
Rate Sensitivity ◽  
High Strength ◽  
Strain Rate Range ◽  
Nickel Cobalt ◽  
Average Grain Size ◽  
High Strain Rate Sensitivity ◽  
Small Activity ◽  
Very High

A bulk and dense nc Ni -24.7% Co with an average grain size of 15nm was fabricated by a direct current electrodeposition. This Ni -24.7% Co exhibits very high tensile strength of 1813MPa to 2232MPa with relatively good tensile ductility of 6.0%~9.6% under tensile test over a wide strain rate range of 0.417s-1 ~ 1.35×10-5s-1. The combination of high strength and good ductility should be attributed to the increased strain hardening ability induced by the addition of alloying Co element. The interaction of dislocation and grain boundaries is the rate-controlling deformation mechanism controlled in the Ni -24.7% Co based on its high strain rate sensitivity of 0.029 and small activity volume of ~14b3.

scholarly journals Micromechanisms of Deformation and Fracture in Porous L-PBF 316L Stainless Steel at Different Strain Rates

Metals ◽  
2021 ◽  
Vol 11 (11) ◽  
pp. 1870
Author(s):  
Nataliya Kazantseva ◽  
Pavel Krakhmalev ◽  
Mikael Åsberg ◽  
Yulia Koemets ◽  
Maxim Karabanalov ◽  
...  
Keyword(s):  
Strain Rate ◽  
316L Stainless Steel ◽  
Loading Rate ◽  
Rate Sensitivity ◽  
High Strength ◽  
Strain Rates ◽  
Microscopic Mechanism ◽  
Powder Bed ◽  
Deformation And Fracture ◽  
Localization Of Plastic Deformation

The process of an unstable plastic flow associated with the strain rate sensitivity of mechanical properties was studied in porous 316L austenitic steel samples manufactured by laser powder bed fusion (L-PBF). Different micromechanisms of deformation and fracture of porous samples dependent on strain rate were found. It was found that despite the porosity, the specimens showed high strength, which increased with the loading rate. Porosity led to lower ductility of the studied specimens, in comparison with literature data for low porous 316L L-PBF samples and resulted in de-localization of plastic deformation. With an increase in strain rate, nucleation of new pores was less pronounced, so that at the highest strain rate of 8, only pore coalescence was observed as the dominating microscopic mechanism of ductile fracture.

Low Temperature Superplasticity in Ultrafine-Grained AZ31 Alloy

2018 ◽  
Vol 385 ◽  
pp. 59-64 ◽  
Author(s):  
Roberto B. Figueiredo ◽  
Pedro Henrique R. Pereira ◽  
Terence G. Langdon
Keyword(s):  
Plastic Deformation ◽  
Strain Rate ◽  
Strain Rate Sensitivity ◽  
Room Temperature ◽  
High Strain ◽  
High Pressure Torsion ◽  
Rate Sensitivity ◽  
Az31 Alloy ◽  
Strain Rates ◽  
Ultrafine Grained

The mechanical behavior of an AZ31 magnesium alloy processed by high-pressure torsion (HPT) was evaluated by tensile testing from room temperature up to 473 K at strain rates between 10-5 – 10-2 s-1. Samples tested at room temperature and at high strain rates at 373 K failed without any plastic deformation. However, significant ductility, with elongations larger than 200%, was observed at 423 K and 473 K and at low strain rates at 373 K. The high elongations are attributed to a pronounced strain hardening and a high strain rate sensitivity. The results agree with reports for a similar alloy processed by severe plastic deformation. However, the level of flow stress is lower and the strain rate sensitivity and the elongations are larger than observed in this alloy processed by conventional thermo-mechanical processing.

Rate-change instrumented indentation for measuring strain rate sensitivity

2009 ◽  
Vol 24 (4) ◽  
pp. 1466-1470 ◽  
Author(s):  
D. Pan ◽  
M.W. Chen
Keyword(s):  
Strain Rate ◽  
Strain Rate Sensitivity ◽  
Metallic Glasses ◽  
Room Temperature ◽  
Rate Sensitivity ◽  
High Strength ◽  
Rate Change ◽  
Instrumented Indentation ◽  
Rate Dependent ◽  
Self Consistency

A rate-change instrumented indentation method is introduced to experimentally characterize the strain rate sensitivity of high strength materials, such as metallic glasses and nanocrystalline metals, which generally possess low rate sensitivity at room temperature. This technique has been validated herein, via self-consistency between rate jump and rate drop measurements, as a viable way to characterize rate dependent deformation behavior and thereby the underlying micromechanisms of plastic flow.

Sign in / Sign up

Export Citation Format

Share Document