Numerical Study of the Thermal Performance in Natural Draft Wet Cooling Tower with Different Fill Types

2012 ◽  
Vol 562-564 ◽  
pp. 1032-1035
Author(s):  
Shui Hua Zheng ◽  
Tai Jin ◽  
Jian Ren Fan
Keyword(s):  
Numerical Simulation ◽  
Mass Transfer ◽  
Thermal Performance ◽  
Cooling Tower ◽  
Numerical Study ◽  
Three Dimensional ◽  
Natural Draft ◽  
Mass Transfer Theory ◽  
Fluent Software ◽  
Fill Depth

Based on the heat and mass transfer theory and characteristics of the FLUENT software, a three-dimensional numerical simulation platform composed by user defined functions had been developed to simulate the thermal performance in a natural draft wet cooling tower. This platform was used to study a typical hyperbolic natural draft wet cooling tower with different fill types. The variations of the flow and temperature field in the cooling tower caused by the two different methods of fill were investigated. It is found that the outlet water temperature will decrease due to the non-uniform fill depth. The non-uniform fill depth is beneficial to increasing the efficiency of the cooling tower.

Three-Dimensional Numerical Study on Thermal Performance in a Natural Draft Wet Cooling Tower

2012 ◽  
Vol 614-615 ◽  
pp. 169-173
Author(s):  
Shui Hua Zheng ◽  
Tai Jin ◽  
Jian Ren Fan
Keyword(s):  
Numerical Simulation ◽  
Mass Transfer ◽  
Thermal Performance ◽  
Water Distribution ◽  
Cooling Tower ◽  
Numerical Study ◽  
Three Dimensional ◽  
Cooling Efficiency ◽  
Natural Draft ◽  
Mass Transfer Theory

Based on the heat and mass transfer theory and characteristics of the CFD software, a three-dimensional numerical simulation platform had been developed to study the thermal performance in a natural draft wet cooling tower. This platform was validated using the measured results of a running cooling tower. The flow and temperature field in the cooling tower were investigated. It is found that the water temperature and flow field can be correctly calculated using this platform. The cooling efficiency could be improved due to non-uniform fill and water distribution methods.

Numerical Study of Natural Draft Wet Cooling Tower

2011 ◽  
Vol 403-408 ◽  
pp. 3191-3194
Author(s):  
Shui Hua Zheng ◽  
Tai Jin ◽  
Jian Ren Fan
Keyword(s):  
Numerical Simulation ◽  
Thermal Performance ◽  
Cooling Tower ◽  
Numerical Study ◽  
Thermal Power ◽  
Three Dimensional ◽  
Design Calculation ◽  
Simulation Platform ◽  
Computational Accuracy ◽  
Natural Draft

Natural draft wet cooling tower is one of key equipments in thermal power stations, and its thermal performance influences the efficiency of total thermal system. Based on the heat and mass transfer theory and characteristics of the FLUENT software, a three-dimensional numerical simulation platform had been developed to simulate the thermal performance in a natural draft wet cooling tower. This platform was used to study the heat exchange and flow situation of a typical hyperbolic natural draft wet cooling tower. Comparing and analyzing the results of simulation and design calculation, it indicate that there is good computational accuracy of the three-dimensional numerical simulation platform, and the platform can provide a good support for the design and research of natural draft wet cooling tower.

Discuss of Important Issues in Numerical Simulation for Natural Draft Counter Flow Cooling Tower

2012 ◽  
Vol 516-517 ◽  
pp. 267-270
Author(s):  
Li Song ◽  
Rui Tian ◽  
Song Li ◽  
Ya Hui Wang
Keyword(s):  
Experimental Data ◽  
Numerical Simulation ◽  
Mass Transfer ◽  
Drop Size ◽  
Cooling Tower ◽  
Drop Diameter ◽  
Atmospheric Density ◽  
Counter Flow ◽  
Natural Draft ◽  
Calculation Results

natural draft counter flow cooling tower heat and mass transfer numerical simulation has been widely used to optimize the cooling tower design and to improve the thermal efficiency, but in published papers, a few important problems is not attracted attention, such as how does impact grid density to the calculation results; how does impact change of atmospheric density to the calculation results; drop diameter is an important parameter in numerical simulation, but it is not a exact experimental data, it is important to discuss how does impact drop size to the calculation results. This paper will explore and analyze these issues in the numerical simulation.

An Investigation of the Effect of interrupted fin arrangements on the Thermal Performance of a Heat Sink under a Free Convection Condition

2019 ◽  
Vol 7 (1) ◽  
pp. 43-53
Author(s):  
Abbas Jassem Jubear ◽  
Ali Hameed Abd
Keyword(s):  
Heat Transfer ◽  
Steady State ◽  
Natural Convection ◽  
Thermal Performance ◽  
Heat Sink ◽  
Numerical Study ◽  
Ansys Fluent ◽  
Fluent Software ◽  
Steady State Heat ◽  
Steady State Heat Transfer

The heat sink with vertically rectangular interrupted fins was investigated numerically in a natural convection field, with steady-state heat transfer. A numerical study has been conducted using ANSYS Fluent software (R16.1) in order to develop a 3-D numerical model.  The dimensions of the fins are (305 mm length, 100 mm width, 17 mm height, and 9.5 mm space between fins. The number of fins used on the surface is eight. In this study, the heat input was used as follows: 20, 40, 60, 80, 100, and 120 watts. This study focused on interrupted rectangular fins with a different arrangement and angle of the fins. Results show that the addition of interruption in fins in various arrangements will improve the thermal performance of the heat sink, and through the results, a better interruption rate as an equation can be obtained.

Numerical Simulation of Gas Flow and Heat Transfer in Cross-Wavy Primary Surface Channel for Microtubine Recuperators

2005 ◽  
Author(s):  
H. X. Liang ◽  
Q. W. Wang ◽  
L. Q. Luo ◽  
Z. P. Feng
Keyword(s):  
Heat Transfer ◽  
Numerical Simulation ◽  
Gas Turbine ◽  
Numerical Study ◽  
High Reliability ◽  
Three Dimensional ◽  
Operating Conditions ◽  
Flow And Heat Transfer ◽  
High Heat Transfer ◽  
The Cross

Three-dimensional numerical simulation was conducted to investigate the flow field and heat transfer performance of the Cross-Wavy Primary Surface (CWPS) recuperators for microturbines. Using high-effective compact recuperators to achieve high thermal efficiency is one of the key techniques in the development of microturbine in recent years. Recuperators need to have minimum volume and weight, high reliability and durability. Most important of all, they need to have high thermal-effectiveness and low pressure-losses so that the gas turbine system can achieve high thermal performances. These requirements have attracted some research efforts in designing and implementing low-cost and compact recuperators for gas turbine engines recently. One of the promising techniques to achieve this goal is the so-called primary surface channels with small hydraulic dimensions. In this paper, we conducted a three-dimensional numerical study of flow and heat transfer for the Cross-Wavy Primary Surface (CWPS) channels with two different geometries. In the CWPS configurations the secondary flow is created by means of curved and interrupted surfaces, which may disturb the thermal boundary layers and thus improve the thermal performances of the channels. To facilitate comparison, we chose the identical hydraulic diameters for the above four CWPS channels. Since our experiments on real recuperators showed that the Reynolds number ranges from 150 to 500 under the operating conditions, we implemented all the simulations under laminar flow situations. By analyzing the correlations of Nusselt numbers and friction factors vs. Reynolds numbers of the four CWPS channels, we found that the CWPS channels have superior and comprehensive thermal performance with high compactness, i.e., high heat transfer area to volume ratio, indicating excellent commercialized application in the compact recuperators.

scholarly journals NUMERICAL SIMULATION OF AIRFLOW AROUND VEHICLE MODELS

2018 ◽  
Vol 56 (3) ◽  
pp. 370
Author(s):  
Nguyen Van Thang ◽  
Ha Tien Vinh ◽  
Bui Dinh Tri ◽  
Nguyen Duy Trong
Keyword(s):  
Numerical Simulation ◽  
Kinetic Energy ◽  
Three Dimensional ◽  
Aerodynamic Characteristics ◽  
Aerodynamic Forces ◽  
Dissipation Energy ◽  
Ansys Fluent ◽  
Car Model ◽  
Airflow Field ◽  
Fluent Software

This article carries out the numerical simulation of airflow over three dimensional car models using ANSYS Fluent software. The calculations have been performed by using realizable k-e turbulence model. The external airflow field of the simplified BMV M6 model with or without a wing is simulated. Several aerodynamic characteristics such as pressure distribution, velocity contours, velocity vectors, streamlines, turbulence kinetic energy and turbulence dissipation energy are analyzed in this study. The aerodynamic forces acting on the car model is calculated and compared with other authors.

The Numerical Simulation of Heat and Mass Transfer in Porous Medium

2011 ◽  
Vol 71-78 ◽  
pp. 4658-4661
Author(s):  
Ling Wang ◽  
Jian Zhang
Keyword(s):  
Numerical Simulation ◽  
Mass Transfer ◽  
Porous Medium ◽  
Heat And Mass Transfer ◽  
Fluent Software

Simulate the heat and mass transfer in 2D cases using fluent software and analyse the results of simulation. Summarize the reasons of neglecting the nature convection under the small Ra number, Furthermore state good thermal retardation properties of porous medium in building.

Sign in / Sign up

Export Citation Format

Share Document