The Oxide Inclusion and Heat-Affected-Zone Toughness for Low Carbon Bridge Steels

2012 ◽  
Vol 562-564 ◽  
pp. 31-34
Author(s):  
Shu Rui Li ◽  
Xue Min Wang ◽  
Chao Chao Zheng ◽  
Xin Lai He
Keyword(s):  
Electron Microscope ◽  
Low Temperature ◽  
Scanning Electron Microscope ◽  
Impact Energy ◽  
Heat Input ◽  
Oxide Inclusion ◽  
Optical Microscope ◽  
Low Carbon ◽  
Temperature Impact ◽  
Scanning Electron

By welding thermo-simulation and actual welding practices, the microstructure and properties of low carbon bridge steels has been studied with the aid of optical microscope, scanning electron microscope. The experimental results show that by the oxide introducing melting technology there are many complex inclusions composed of oxide containing Ti and MnS. These inclusions are spherical and they are distributed homogeneously. During the welding thermo-simulation these oxide inclusions will promote the nucleation of acicular ferrite and make the microstructure in HAZ finer. Therefore the toughness in HAZ is good whether in welding thermo-simulation even if the heat input reaches to 200kJ/cm. In actual welding the heat input is 88kJ/cm and the low temperature impact energy still can reach 110J.

scholarly journals The Effect of Hot-Mounting on the Microstructure of an As-Quenched Auto-Tempered Low-Carbon Martensitic Steel

Metals ◽  
2019 ◽  
Vol 9 (5) ◽  
pp. 550 ◽  
Author(s):  
Shashank Ramesh Babu ◽  
Matias Jaskari ◽  
Antti Järvenpää ◽  
David Porter
Keyword(s):  
Electron Microscope ◽  
Low Temperature ◽  
Scanning Electron Microscope ◽  
Martensitic Steel ◽  
Low Carbon ◽  
Martensitic Steels ◽  
Potential Growth ◽  
Scanning Electron ◽  
Additional Tempering ◽  
Carbon Martensitic Steel

The effect of hot-mounting for metallographic studies of as-quenched low-carbon martensitic steels has been studied. Hot-mounting is typically carried out at 150–200 °C, i.e., a low-temperature tempering regime. Cold- and hot-mounted specimens from an as-quenched low-carbon auto-tempered steel were examined using a scanning electron microscope and their hardness levels were also compared. It was found that hot-mounting causes additional tempering that manifests as the appearance of new precipitates in those regions that are free of auto-tempered cementite. The observations were rationalized using DICTRA simulations to calculate the potential growth of cementite. Hot-mounting was also shown to cause a small but statistically significant increase in the hardness of the martensite.

Effect of Casting Overheat and Rolling Temperature on Morphology of Sulfide in 30MnVS Steel

2012 ◽  
Vol 457-458 ◽  
pp. 270-273
Author(s):  
Yi You Tu ◽  
Guo Zhong Li
Keyword(s):  
Electron Microscope ◽  
Scanning Electron Microscope ◽  
Continuous Casting ◽  
Optical Microscope ◽  
Rolling Temperature ◽  
Ferrite Content ◽  
Continuous Casting Slab ◽  
Intragranular Ferrite ◽  
Sulfide Segregation ◽  
Scanning Electron

Effect of superheat and initial rolling temperature on the morphology and distribution of sulfide in non quenched and tempered free cutting steel 30MnVS has been studied by optical microscope and scanning electron microscope. Results show that proper superheat and initial rolling temperature can turn rod-shaped sulfide into massive or globular sulfide，to alleviate sulfide segregation and pro-eutectoid ferrite distribution along the boundary of pearlite clusters in 30MnVS , increase the intragranular ferrite content and optimize the structure of continuous casting slab.

Analysis of an Axle Failure under Torsional Load

2016 ◽  
Vol 850 ◽  
pp. 101-106 ◽  
Author(s):  
Shu Mei Li ◽  
Jian Jun Yang ◽  
Wei Dong Zhang ◽  
August Chang ◽  
Cai Xia Zhang ◽  
...  
Keyword(s):  
Electron Microscope ◽  
Scanning Electron Microscope ◽  
Failure Mechanism ◽  
Field Testing ◽  
Optical Microscope ◽  
Fatigue Lifetime ◽  
Torsional Load ◽  
Torsional Fatigue ◽  
Secondary Cracks ◽  
Scanning Electron

Premature fracture of an axle under torsional load occurred after a tracked military tank had experienced field testing for only 80 kilometers. Visual metallographic examinations were performed with optical microscope (OM) and scanning electron microscope (SEM). The investigation demonstrates that the premature fracture is caused by metallurgical problems inside the axle where the primary and secondary cracks originate, propagate, and eventually result in final catastrophic rupture through torsional fatigue. The failure mechanism is summarized and improvement of the fatigue lifetime for the axle is recommended.

Investigation on the Microstructure Hardness for the Hot Compressed Duplex Steel

2022 ◽  
Vol 905 ◽  
pp. 30-37
Author(s):  
Shu Lan Zhang ◽  
Xiao Dan Zhang ◽  
Hai Feng Xu ◽  
Chang Wang
Keyword(s):  
Electron Microscope ◽  
Scanning Electron Microscope ◽  
Optical Microscope ◽  
Ferrite Phase ◽  
Ferrite Formation ◽  
Average Hardness ◽  
Duplex Steel ◽  
Quench Temperature ◽  
Fluctuation Range ◽  
Scanning Electron

Effect of microstructure size and type on the hardness for the duplex steel were disclosed by using of optical microscope (OM), scanning electron microscope (SEM) and nanoindenter for the samples hot compressed under different temperature with reduction of 10%, 30%, 50% and 70%. OM and SEM were used to measure the average martensite lamellar width, space and indenter morphology. nanoindenter test characterized the microstructure hardness for the samples under different process. Experiment results show that martensite hardness for the sample hot compressed at 950°C has larger diversity than that of sample hot compressed at 1200°C. The martensite hardness fluctuation range for the sample compressed at 950°C is almost from about 7GPa to 12GPa, while, for the sample compressed at 1200°C, the fluctuation range is basically from about 9GPa to 12GPa. However, the average hardness for the samples hot compressed at 950°C is comparably smaller, which is related with lower quench temperature. The larger martensite hardness fluctuation is mainly related with induced ferrite formation and finer martensite lamellar width. For the ferrite phase, the hardness fluctuation range is lower.

CHARACTERISATION OF BIOMEDICAL TITANIUM LAYERS DEPOSITED BY A VACUUM PLASMA SPRAY PROCESS

2021 ◽  
Vol 55 (2) ◽  
pp. 231-235
Author(s):  
Mihailo Mrdak ◽  
Darko Bajić ◽  
Darko Veljić ◽  
Marko Rakin
Keyword(s):  
Electron Microscope ◽  
Scanning Electron Microscope ◽  
Hardness Test ◽  
Optical Microscope ◽  
Mechanical Tests ◽  
Test Method ◽  
Bonding Layer ◽  
Vacuum Plasma Spray ◽  
Porous Ti ◽  
Scanning Electron

In this paper we will describe the process of the deposition of thick layers of VPS-Ti coating, which is used as a bonding layer for the upper porous Ti coatings on implant substrates. In order to deposit the powder, we used HÖGANÄS Ti powder labelled as AMPERIT 154.086 -63 µm. In order to test the mechanical properties and microstructure of the VPS-Ti coating, the powder was deposited on Č.4171 (X15Cr13 EN10027) steel substrates. Mechanical tests of the microhardness of the coating were performed by the Vickers hardness test method (HV0.3) and tensile strength by measuring the force per unit area (MPa). The microhardness of the coating is 159 HV0.3, which is consistent with the microstructure. The coating was found to have a good bond strength of 68 MPa. The morphology of the powder particles was examined on a scanning electron microscope. The microstructure of the coating, both when deposited and etched, was examined with an optical microscope and a scanning electron microscope. By etching the coating layers, it was found that the structure is homogeneous and that it consists of a mixture of low-temperature and high-temperature titanium phases (α-Ti + β-Ti). Our tests have shown that the deposited layers of Ti coating can be used as a bonding layer for porous Ti coatings in the production of implants.

scholarly journals Magnetism and Microstructure Characterization of Phase Transitions in a Steel

2014 ◽  
Vol 2014 ◽  
pp. 1-4
Author(s):  
M. Güler
Keyword(s):  
Mössbauer Spectroscopy ◽  
Phase Transitions ◽  
Electron Microscope ◽  
Scanning Electron Microscope ◽  
Mossbauer Spectroscopy ◽  
Low Carbon Steel ◽  
Magnetic Characteristics ◽  
Low Carbon ◽  
Mößbauer Spectroscopy ◽  
Scanning Electron

We present phase transitions in a low carbon steel according to existing phases and their magnetism. Scanning electron microscope employed research to clarify and evaluate the microstructural details. Additionally, we utilized from Mössbauer spectroscopy for magnetic characteristics of different existed phases. Scanning electron microscope examinations showed that the pure state of the steel was fully in the ferrite phase with equiaxed grains. Moreover, subsequent heat treatments on the studied steel also ensured the first austenite and then pearlite phase formation. Mössbauer spectroscopy of these phases appeared as a paramagnetic single-line absorption peak for the austenite phase and ferromagnetic six-line spectra for both ferrite and pearlite phases. From Mössbauer data, we determined that the internal magnetic fields of ferrite and pearlite phases were as 32.2 Tesla and 31.3 Tesla, respectively.

Clouding of Pressed Potassium Bromide Powder

1972 ◽  
Vol 26 (2) ◽  
pp. 247-251 ◽  
Author(s):  
William P. Norris ◽  
Allen L. Olsen ◽  
Richard G. Brophy
Keyword(s):  
Electron Microscope ◽  
Scanning Electron Microscope ◽  
Adsorbed Water ◽  
Optical Microscope ◽  
Potassium Bromide ◽  
Monomolecular Layer ◽  
Cloudy Region ◽  
Weak Zones ◽  
Ground Powder ◽  
Scanning Electron

The monomolecular layer of water adsorbed on KBr particles is responsible for clouding of disks pressed from finely ground powder. Cloudiness is caused by formation of a multitude of cracks in the disk. The initial cracking can be observed with a low power optical microscope and the extensive cracking in the fully cloudy region is observable with a scanning electron microscope. It is suggested that adsorbed water promotes recrystallization, generating weak zones in the workhardened, elastically stressed disk which fails by cracking.

Sign in / Sign up

Export Citation Format

Share Document