scholarly journals Cracking Behaviors and Mechanical Properties of Rock-Like Specimens with Two Unparallel Flaws under Conventional Triaxial Compression

2019 ◽  
Vol 2019 ◽  
pp. 1-15 ◽  
Author(s):  
Huilin Le ◽  
Shaorui Sun ◽  
Chenghua Xu ◽  
Liuyang Li ◽  
Yong Liu
Keyword(s):  
Mechanical Properties ◽  
Inclination Angle ◽  
Failure Modes ◽  
Shear Failure ◽  
Triaxial Compression ◽  
Confining Pressure ◽  
Critical Value ◽  
Tensile Failure ◽  
Rock Bridge ◽  
Bridge Length

Flaws existing in rock masses are generally unparallel and under three-dimensional stress; however, the mechanical and cracking behaviors of the specimens with two unparallel flaws under triaxial compression have been rarely studied. Therefore, this study conducted comprehensive research on the cracking and coalescence behavior and mechanical properties of specimens with two unparallel flaws under triaxial compression. Triaxial compressive tests were conducted under different confining pressures on rock-like specimens with two preexisting flaws but varying flaw geometries (with respect to the inclination angle of the two unparallel flaws, rock bridge length, and rock bridge inclination angle). Six crack types and eleven coalescence types in the bridge region were observed, and three types of failure modes (tensile failure, shear failure, and tensile-shear failure) were observed in experiments. Test results show that bridge length and bridge inclination angle have an effect on the coalescence pattern, but the influence of bridge inclination angle is larger than that of the bridge length. When the confining pressure is low, coalescence patterns and failure modes of the specimens are greatly affected by flaw geometry, but when confining pressure rose to a certain level, the influence of confining pressure is larger than the effect of flaw geometry. The peak strength of the specimens is affected by flaw geometry and confining pressure. There is a critical value for the bridge length. If the bridge length is larger than the critical value, peak strengths of the samples almost keep constant as the bridge length increases. In addition, as the bridge inclination angle increases, there is an increase in the probability of tensile cracks occurring, and with an increase in the confining pressure, the probability of the occurrence of shear cracks increases.

scholarly journals Experimental Investigation on Failure Modes and Mechanical Properties of Rock-Like Specimens with a Grout-Infilled Flaw under Triaxial Compression

2019 ◽  
Vol 2019 ◽  
pp. 1-14
Author(s):  
Huilin Le ◽  
Shaorui Sun ◽  
Feng Zhu ◽  
Haotian Fan
Keyword(s):  
Mechanical Properties ◽  
Rock Mass ◽  
Epoxy Resin ◽  
Failure Modes ◽  
Shear Failure ◽  
Fractured Rock ◽  
Triaxial Compression ◽  
Friction Angle ◽  
Confining Pressure ◽  
Compression Tests

Flaws existing in rock mass are one of the main factors resulting in the instability of rock mass. Epoxy resin is often used to reinforce fractured rock mass. However, few researches focused on mechanical properties of the specimens with a resin-infilled flaw under triaxial compression. Therefore, in this research, epoxy resin was selected as the grouting material, and triaxial compression tests were conducted on the rock-like specimens with a grout-infilled flaw having different geometries. This study draws some new conclusions. The high confining pressure suppresses the generation of tensile cracks, and the failure mode changes from tensile-shear failure to shear failure as the confining pressure increases. Grouting with epoxy resin leads to the improvement of peak strengths of the specimens under triaxial compression. The reinforcement effect of epoxy resin is better for the specimens having a large flaw length and those under a relatively low confining pressure. Grouting with epoxy resin reduces the internal friction angle of the samples but improves their cohesion. This research may provide some useful insights for understanding the mechanical behaviors of grouted rock masses.

scholarly journals Experimental Study on the Mechanical Properties and Seepage Characteristics of Red Sandstone with a Single Persistent Joint under Triaxial Compression

Geofluids ◽  
2021 ◽  
Vol 2021 ◽  
pp. 1-13
Author(s):  
Wei Wang ◽  
Shifan Liu ◽  
Chong Shi ◽  
Shanxi Zheng ◽  
Qizhi Zhu
Keyword(s):  
Mechanical Properties ◽  
Pore Pressure ◽  
Failure Modes ◽  
Shear Failure ◽  
Triaxial Compression ◽  
Confining Pressure ◽  
Strengthening Effect ◽  
Red Sandstone ◽  
Inclination Angles ◽  
Seepage Characteristics

In this research, the conventional triaxial compression experiments for intact red sandstone specimens and the specimens with a single persistent joint at different inclination angles, i.e., 0°, 30°, 45°, and 90°, were conducted at first. Based on the results of the conventional tests, the effects of the confining pressure and the joint inclination angle on the mechanical properties including deformation behavior and strength parameters were summarized and analyzed, respectively. We find that the strength and deformation of jointed red sandstone are enlarged due to the increment of confining pressure, and the mechanical parameters of specimens show a U-shaped development with the rise of the joint angle. Besides, to investigate the effects of the pore pressure on seepage characteristics of rocks with joint angles at 0°, 45°, and 90°, a series of triaxial compression drainage tests on the jointed red sandstone were performed. The results show that the pore pressure has a weakening effect on the strength of jointed specimens, which can reduce the strengthening effect induced by confining pressure. Meanwhile, the tested specimens mostly present shear failure modes. As a result, the mechanical responses, seepage characteristics, and cracking modes in red sandstone containing a single persistent joint under triaxial compression are revealed.

scholarly journals Experimental Study on Rock-Like Specimens with Single Flaw under Hydro-Mechanical Coupling

2019 ◽  
Vol 9 (16) ◽  
pp. 3234 ◽  
Author(s):  
Jinquan Xing ◽  
Cheng Zhao ◽  
Songbo Yu ◽  
Hiroshi Matsuda ◽  
Chuangchuang Ma
Keyword(s):  
Mechanical Properties ◽  
Shear Failure ◽  
Water Pressure ◽  
Triaxial Compression ◽  
Confining Pressure ◽  
Tensile Failure ◽  
Compression Tests ◽  
Cracking Behavior ◽  
Mechanical Coupling ◽  
High Confining Pressure

In order to study the mechanical characteristics and cracking behavior of jointed rock mass under hydro-mechanical coupling, a series of uniaxial compression tests and triaxial compression tests were carried out on cylinder gypsum specimens with a single pre-existing flaw. Under different confining pressures, water pressure was injected on the pre-existing flaw surface through a water injection channel. The geometrical morphology and tensile or shear properties of the cracks were determined by X-ray computed tomography (CT) and scanning electron microscope (SEM). Based on the macro and micro observation, nine types of cracks that caused the specimen failure are summarized. The results of mechanical properties and crack behavior showed that the confining pressure inhibited the tensile cracks, and shear failure occurred under high confining pressure. The water pressure facilitated the initiation and extension of tensile crack, which made the specimens prone to tensile failure. However, under the condition of high confining pressure and low water pressure, the lubrication effect had a significant effect on the failure pattern, under which the specimens were prone to shear failure. This experimental research on mechanical properties and cracking behavior under hydro-mechanical coupling is expected to increase its fundamental understanding.

scholarly journals Experimental Study of the Mechanical Characteristics of a Rock-Like Material Containing a Preexisting Fissure under Loading and Unloading Triaxial Compression

2020 ◽  
Vol 2020 ◽  
pp. 1-12 ◽  
Author(s):  
Taoli Xiao ◽  
Mei Huang ◽  
Min Gao
Keyword(s):  
Experimental Study ◽  
Failure Mode ◽  
Mechanical Characteristics ◽  
Failure Modes ◽  
Shear Failure ◽  
Triaxial Compression ◽  
Tensile Failure ◽  
Underground Engineering ◽  
Inclination Angles ◽  
Loading And Unloading

An experimental study of a rock-like material containing a preexisting fissure subjected to loading and unloading triaxial compression is carried out, and the results show that the mechanical characteristics of the rock-like specimen depend heavily on the loading paths and the inclination of the fissure. The triaxial loading experiment results show that the failure strength linearly increases, while the residual strength linearly decreases with increasing inclination. Furthermore, specimens subjected to triaxial compression show an “X”-type shear failure mode. The triaxial unloading compression experimental results show that specimens with different inclination angles have various failure modes. Specimens with gentle inclinations show a tensile-shear mix failure mode, specimens with middle inclinations show a shear-sliding failure mode, and specimens with steep inclinations show a tensile failure mode. These findings can be used to forecast excavation-induced instabilities in deep underground engineering rock structures.

scholarly journals Strength and Failure Characteristics of Saturated Sandstone Under Loading and Unloading

2021 ◽  
Author(s):  
Zhenhua Zhang ◽  
Huayan Yao ◽  
Hongguo Li ◽  
Hanbin Bian ◽  
Dayong Zhu
Keyword(s):  
Failure Modes ◽  
Shear Failure ◽  
Water Saturation ◽  
Triaxial Compression ◽  
Axial Direction ◽  
Confining Pressure ◽  
Stress Path ◽  
Failure Characteristics ◽  
Dry Conditions ◽  
Unloading Confining Pressure

Abstract Water has effects on the strength and failure characteristics of the sandstone in natural environment. Conventional triaxial compressive or unloading confining pressure experiments were conducted on sandstone specimens. Experimental results indicate that the compressive strength of sandstone decreases significantly under saturated conditions in comparison with dry conditions, the strength parameters of saturated specimens under unloading confining pressure are also lower than those of dry rock samples; for the sandstone with the same water content, the strengths under triaxial unloading confining pressure is slightly higher than those under triaxial compressive condition; compared with the stress path of triaxial compression, the stress path of unloading confining pressure makes cracks propagate more easily along the axial direction, and the angle between fracture surface and axial direction is smaller. Under triaxial unloading confining pressure, there failure modes of dry sandstone are tension failure and shear failure, while that of saturated sandstone is mainly shear failure. In the process of water saturation, the bond and friction characteristics between grain particles are degraded due to water weakening the cementation between the grain particles and softening grains boundary, and the expansion of clay minerals in the sandstone, which leads to the decrease of macroscopic mechanical strengths.

scholarly journals Experimental Investigation on the Mechanical Characteristics and Deformation Behaviour of Fractured Rock-Like Material with One Single Fissure under the Conventional Triaxial Compression

2018 ◽  
Vol 2018 ◽  
pp. 1-11 ◽  
Author(s):  
Taoli Xiao ◽  
Mei Huang ◽  
Cheng Cheng ◽  
Yunlong He
Keyword(s):  
Mechanical Characteristics ◽  
Failure Modes ◽  
Shear Failure ◽  
Early Stage ◽  
Fractured Rock ◽  
Deformation Behaviour ◽  
Triaxial Compression ◽  
Strain Curve ◽  
Confining Pressure ◽  
Material Specimen

An experimental study was carried out on a rock-like material specimen containing a single fissure to investigate its mechanical characteristics and deformation behaviour under triaxial compression. The mechanical characteristics, such as peak strength and residual strength, are discussed. The confining pressure had a distinct effect on the ductility characteristics of the specimen. “A distinct stress drop” occurred in the early stage of the stress-strain curve when the length fissure was relatively long. The I-crack, II-crack, and III-crack are all observed under triaxial compression, and the III-crack is commonly observed under triaxial compression. Confining pressure plays an essential role in affecting the failure mode of the specimen. There are three kinds of failure modes in the triaxial compression experiment on a rock-like material specimen with one single fissure: tensile-shear comprehensive failure, “X”-shaped shear failure, and shear failure along the fissure plane. These results are important and fundamental to understand the fracture mechanism of rock engineering.

scholarly journals Mechanical Properties and Damage in Lignite under Combined Cyclic Compression and Shear Loading

2020 ◽  
Vol 12 (20) ◽  
pp. 8393
Author(s):  
Haoshuai Wu ◽  
Haibo Bai ◽  
Yanlong Chen ◽  
Hai Pu ◽  
Kai Zhang
Keyword(s):  
Mechanical Properties ◽  
Inclination Angle ◽  
Shear Failure ◽  
Cyclic Stress ◽  
Shear Loading ◽  
Tensile Failure ◽  
Shear Tests ◽  
Volume Strain ◽  
Cyclic Compression ◽  
Upper Limit

In this paper, uniaxial cyclic compression and shear test was carried out for lignite samples. The effects of inclination angle (θ) and upper limit of cyclic stress (σmax) on mechanical properties of coal samples were analyzed, and the damage variables of coal samples were studied based on energy dissipation theory. The results show that the uniaxial compressive strength (UCS) of coal samples after uniaxial cyclic compression and shear tests decreases with the increase of the upper limit of cyclic stress and inclination angle. The shear stress component generated by the increase of inclination angle can effectively reduce the UCS and increase the damage degree of coal samples. With the increase of inclination angle, the failure mode of coal samples is changed from tensile failure (θ = 0°), the combined tensile failure and shear failure (θ = 5°) to shear failure (θ = 10°). The peak axial and radial strain of coal samples first increases rapidly and then stagnates. The peak volume strain rapid increases and then stagnates (θ = 0° and θ = 5°). When the inclination angle is 10°, the peak volume strain first decreases rapidly and then stagnates. Even if the upper limit of cyclic stress is lower than its UCS, it will still promote the propagation of micro cracks and the generation of new cracks and increase the internal damage of coal samples. With the increase of the cycle number, damage variables of coal samples after uniaxial cyclic compression and shear tests nonlinearly increase, and the growth rate decreases gradually.

scholarly journals Mechanical Properties and Failure Modes of Thick-Walled Cylinder Granites with Different Apertures under Triaxial Compression

2020 ◽  
Vol 2020 ◽  
pp. 1-18
Author(s):  
Wei Chen ◽  
Wen Wan ◽  
Shuailong Lian ◽  
Senlin Xie ◽  
Yu Zhou ◽  
...  
Keyword(s):  
Failure Modes ◽  
Shear Failure ◽  
Triaxial Compression ◽  
Confining Pressure ◽  
Outer Wall ◽  
Surrounding Rock ◽  
Compression Tests ◽  
Deformation And Failure ◽  
Triaxial Compressive Strength ◽  
Walled Cylinder

Roadway excavation changes the original equilibrium stress state of the rock mass, resulting in the loading and unloading of the surrounding rock near the free surface. After the excavation, the tangential stress increases and the radial stress decreases, which mainly cause deformation and collapse of the roadway. In order to study the strength characteristics of the surrounding rock after the excavation, one effective way is to carry out triaxial compression tests on small surrounding rock samples. Therefore, this paper focuses on the triaxial compression mechanical propertiesof thick-walled cylinder granites with an electrohydraulic, servo-controlled rock mechanics testing system (MTS-815). It studies how different pore sizes and confining pressures affect the triaxial compressive strength (TCS), deformation, and failure modes of granite samples. The results are as follows: (1) Under triaxial compression, the stress-strain curves have no obvious yield stage, and the peak TCS increases with the confining pressure (σ3). When σ3 is low, there is little difference in the TCS between the complete specimen and the thick-walled cylinders. When σ3 reaches 30 MPa∼40 MPa, the TCS of samples with apertures of 15 mm and 20 mm are obviously lower. The σ3 has an obvious influence on the elastic modulus of thick-walled cylinder granites. (2) Shearing and splitting are the main failure modes under triaxial compression. When σ3 is low, shear failure appears. As σ3 reaches 30 MPa∼40 MPa, split failure occurs. The area of the fracture surface increases with σ3. (3) As σ3 grows, the influence parameter (m) of the three-dimensional Hoek-Brown criterion increases. Under the same σ3, the value of m presents a decreasing trend from the outer wall to the inner wall, which means the bearing capacity keeps getting lower and lower. As a result, the inner wall is most likely to be damaged. The theoretical analysis results agree well with the tests.

Experimental Investigation on Mechanical Properties of Soft Rock under Instantaneous Triaxial Compression

2012 ◽  
Vol 594-597 ◽  
pp. 218-221
Author(s):  
Yu Wang ◽  
Feng Liu
Keyword(s):  
Mechanical Properties ◽  
Shear Failure ◽  
Triaxial Compression ◽  
Deformation Modulus ◽  
Soft Rock ◽  
Confining Pressure ◽  
Test System ◽  
Compression Tests ◽  
Confining Pressures ◽  
Failure Angle

Using the RMT-150C rock mechanics test system, the instantaneous triaxial compression tests for muddy siltstone were carried out under different confining pressures, and the instantaneous mechanical properties of soft rock were obtained. The results show that the strength parameters of sample have a positive linear relation with the confining pressure, and the sensitivity of peak strength on the confining pressure is higher than that of residual strength. The elastic and deformation modulus of sample linearly increase with the confining pressure going up, and the elastic modulus is more sensitive to the confining pressure. The soft rock sample shows typical ductility failure characteristic, while the damage characteristic is mainly shear failure and the shear failure angle linearly decreases with the confining pressure going up.

Study on mechanical properties and damage evolution of carbonaceous shale under triaxial compression with acoustic emission

2021 ◽  
pp. 105678952199119
Author(s):  
Kai Yang ◽  
Qixiang Yan ◽  
Chuan Zhang ◽  
Wang Wu ◽  
Fei Wan
Keyword(s):  
Mechanical Properties ◽  
Acoustic Emission ◽  
Water Content ◽  
Damage Evolution ◽  
Damage Assessment ◽  
Triaxial Compression ◽  
Confining Pressure ◽  
Damage Variable ◽  
Natural State ◽  
Carbonaceous Shale

To explore the mechanical properties and damage evolution characteristics of carbonaceous shale with different confining pressures and water-bearing conditions, triaxial compression tests accompanied by simultaneous acoustic emission (AE) monitoring were conducted on carbonaceous shale rock specimens. The AE characteristics of carbonaceous shale were investigated, a damage assessment method based on Shannon entropy of AE was further proposed. The results suggest that the mechanical properties of carbonaceous shale intensify with increasing confining pressure and degrade with increasing water content. Moisture in rocks does not only weaken the cohesion but also reduce the internal friction angle of carbonaceous shale. It is observed that AE activities mainly occur in the post-peak stage and the strong AE activities of saturated carbonaceous shale specimens appear at a lower normalized stress level than that of natural-state specimens. The maximum AE counts and AE energy increase with water content while decrease with confining pressure. Both confining pressure and water content induce changes in the proportions of AE dominant frequency bands, but the changes caused by confining pressure are more significant than those caused by water content. The results also indicate that AE entropy can serve as an applicable index for rock damage assessment. The damage evolution process of carbonaceous shale can be divided into two main stages, including the stable damage development stage and the damage acceleration stage. The damage variable increases slowly accompanied by a few AE activities at the first stage, which is followed by a rapid growth along with intense acoustic emission activities at the damage acceleration stage. Moreover, there is a sharp rise in the damage evolution curve for the natural-state specimen at the damage acceleration stage, while the damage variable develops slowly for the saturated-state specimen.

Sign in / Sign up

Export Citation Format

Share Document