scholarly journals Experimental Study on Rock-Like Specimens with Single Flaw under Hydro-Mechanical Coupling

2019 ◽  
Vol 9 (16) ◽  
pp. 3234 ◽  
Author(s):  
Jinquan Xing ◽  
Cheng Zhao ◽  
Songbo Yu ◽  
Hiroshi Matsuda ◽  
Chuangchuang Ma
Keyword(s):  
Mechanical Properties ◽  
Shear Failure ◽  
Water Pressure ◽  
Triaxial Compression ◽  
Confining Pressure ◽  
Tensile Failure ◽  
Compression Tests ◽  
Cracking Behavior ◽  
Mechanical Coupling ◽  
High Confining Pressure

In order to study the mechanical characteristics and cracking behavior of jointed rock mass under hydro-mechanical coupling, a series of uniaxial compression tests and triaxial compression tests were carried out on cylinder gypsum specimens with a single pre-existing flaw. Under different confining pressures, water pressure was injected on the pre-existing flaw surface through a water injection channel. The geometrical morphology and tensile or shear properties of the cracks were determined by X-ray computed tomography (CT) and scanning electron microscope (SEM). Based on the macro and micro observation, nine types of cracks that caused the specimen failure are summarized. The results of mechanical properties and crack behavior showed that the confining pressure inhibited the tensile cracks, and shear failure occurred under high confining pressure. The water pressure facilitated the initiation and extension of tensile crack, which made the specimens prone to tensile failure. However, under the condition of high confining pressure and low water pressure, the lubrication effect had a significant effect on the failure pattern, under which the specimens were prone to shear failure. This experimental research on mechanical properties and cracking behavior under hydro-mechanical coupling is expected to increase its fundamental understanding.

scholarly journals Cracking Behaviors and Mechanical Properties of Rock-Like Specimens with Two Unparallel Flaws under Conventional Triaxial Compression

2019 ◽  
Vol 2019 ◽  
pp. 1-15 ◽  
Author(s):  
Huilin Le ◽  
Shaorui Sun ◽  
Chenghua Xu ◽  
Liuyang Li ◽  
Yong Liu
Keyword(s):  
Mechanical Properties ◽  
Inclination Angle ◽  
Failure Modes ◽  
Shear Failure ◽  
Triaxial Compression ◽  
Confining Pressure ◽  
Critical Value ◽  
Tensile Failure ◽  
Rock Bridge ◽  
Bridge Length

Flaws existing in rock masses are generally unparallel and under three-dimensional stress; however, the mechanical and cracking behaviors of the specimens with two unparallel flaws under triaxial compression have been rarely studied. Therefore, this study conducted comprehensive research on the cracking and coalescence behavior and mechanical properties of specimens with two unparallel flaws under triaxial compression. Triaxial compressive tests were conducted under different confining pressures on rock-like specimens with two preexisting flaws but varying flaw geometries (with respect to the inclination angle of the two unparallel flaws, rock bridge length, and rock bridge inclination angle). Six crack types and eleven coalescence types in the bridge region were observed, and three types of failure modes (tensile failure, shear failure, and tensile-shear failure) were observed in experiments. Test results show that bridge length and bridge inclination angle have an effect on the coalescence pattern, but the influence of bridge inclination angle is larger than that of the bridge length. When the confining pressure is low, coalescence patterns and failure modes of the specimens are greatly affected by flaw geometry, but when confining pressure rose to a certain level, the influence of confining pressure is larger than the effect of flaw geometry. The peak strength of the specimens is affected by flaw geometry and confining pressure. There is a critical value for the bridge length. If the bridge length is larger than the critical value, peak strengths of the samples almost keep constant as the bridge length increases. In addition, as the bridge inclination angle increases, there is an increase in the probability of tensile cracks occurring, and with an increase in the confining pressure, the probability of the occurrence of shear cracks increases.

scholarly journals Experimental Investigation on Failure Modes and Mechanical Properties of Rock-Like Specimens with a Grout-Infilled Flaw under Triaxial Compression

2019 ◽  
Vol 2019 ◽  
pp. 1-14
Author(s):  
Huilin Le ◽  
Shaorui Sun ◽  
Feng Zhu ◽  
Haotian Fan
Keyword(s):  
Mechanical Properties ◽  
Rock Mass ◽  
Epoxy Resin ◽  
Failure Modes ◽  
Shear Failure ◽  
Fractured Rock ◽  
Triaxial Compression ◽  
Friction Angle ◽  
Confining Pressure ◽  
Compression Tests

Flaws existing in rock mass are one of the main factors resulting in the instability of rock mass. Epoxy resin is often used to reinforce fractured rock mass. However, few researches focused on mechanical properties of the specimens with a resin-infilled flaw under triaxial compression. Therefore, in this research, epoxy resin was selected as the grouting material, and triaxial compression tests were conducted on the rock-like specimens with a grout-infilled flaw having different geometries. This study draws some new conclusions. The high confining pressure suppresses the generation of tensile cracks, and the failure mode changes from tensile-shear failure to shear failure as the confining pressure increases. Grouting with epoxy resin leads to the improvement of peak strengths of the specimens under triaxial compression. The reinforcement effect of epoxy resin is better for the specimens having a large flaw length and those under a relatively low confining pressure. Grouting with epoxy resin reduces the internal friction angle of the samples but improves their cohesion. This research may provide some useful insights for understanding the mechanical behaviors of grouted rock masses.

Experimental Investigation on Mechanical Properties of Soft Rock under Instantaneous Triaxial Compression

2012 ◽  
Vol 594-597 ◽  
pp. 218-221
Author(s):  
Yu Wang ◽  
Feng Liu
Keyword(s):  
Mechanical Properties ◽  
Shear Failure ◽  
Triaxial Compression ◽  
Deformation Modulus ◽  
Soft Rock ◽  
Confining Pressure ◽  
Test System ◽  
Compression Tests ◽  
Confining Pressures ◽  
Failure Angle

Using the RMT-150C rock mechanics test system, the instantaneous triaxial compression tests for muddy siltstone were carried out under different confining pressures, and the instantaneous mechanical properties of soft rock were obtained. The results show that the strength parameters of sample have a positive linear relation with the confining pressure, and the sensitivity of peak strength on the confining pressure is higher than that of residual strength. The elastic and deformation modulus of sample linearly increase with the confining pressure going up, and the elastic modulus is more sensitive to the confining pressure. The soft rock sample shows typical ductility failure characteristic, while the damage characteristic is mainly shear failure and the shear failure angle linearly decreases with the confining pressure going up.

Behaviors of Xiashu Loess in the Lower Reaches of China’s Yangtze River under Triaxial Compression and the Microscopic Explanations

2016 ◽  
Vol 858 ◽  
pp. 91-97
Author(s):  
Jun Hua Xiao ◽  
Wen Qi Zheng
Keyword(s):  
Mechanical Properties ◽  
Yangtze River ◽  
Shear Failure ◽  
Triaxial Compression ◽  
Processing Technique ◽  
Point Of View ◽  
Image Processing Technique ◽  
Test Results ◽  
Compression Tests ◽  
Triaxial Compression Tests

To investigate the macroscopic mechanical properties of undisturbed structural Xiashu loess in the lower reaches of China’s Yangtze River under triaxial compression, and obtain the intrinsic explanations for the macroscopic mechanical properties from the microscopic point of view, in laboratory, triaxial compression tests were carried out, microstructure images of sheared samples were collected by scanning electron microscope (SEM), and quantitative parameters of microstructure (mainly about particle or pore size, distribution, and alignment) were extracted by digital image processing technique. Based on the test results, the deviator stress-strain relationships of both undisturbed and remoulded Xiashu loess, the structural strength, and the microstructural evolution mechanism about the formation of shear failure zone of Xiashu loess under triaxial compression were analyzed.

scholarly journals Triaxial Testing of Geosynthetics Reinforced Tailings with Different Reinforced Layers

Materials ◽  
2020 ◽  
Vol 13 (8) ◽  
pp. 1943
Author(s):  
Fu Yi ◽  
Changbo Du
Keyword(s):  
Triaxial Compression ◽  
Friction Angle ◽  
Confining Pressure ◽  
Test Results ◽  
Compression Tests ◽  
Strength Index ◽  
Stress Strain ◽  
High Confining Pressure ◽  
Zhang Model ◽  
Triaxial Compression Tests

To evaluate the shear properties of geotextile-reinforced tailings, triaxial compression tests were performed on geogrids and geotextiles with zero, one, two, and four reinforced layers. The stress–strain characteristics and reinforcement effects of the reinforced tailings with different layers were analyzed. According to the test results, the geogrid stress–strain curves show hardening characteristics, whereas the geotextile stress–strain curves have strain-softening properties. With more reinforced layers, the hardening or softening characteristics become more prominent. We demonstrate that the stress–strain curves of geogrids and geotextile reinforced tailings under different reinforced layers can be fitted by the Duncan–Zhang model, which indicates that the pseudo-cohesion of shear strength index increases linearly whereas the friction angle remains primarily unchanged with the increase in reinforced layers. In addition, we observed that, although the strength of the reinforced tailings increases substantially, the reinforcement effect is more significant at a low confining pressure than at a high confining pressure. On the contrary, the triaxial specimen strength decreases with the increase in the number of reinforced layers. Our findings can provide valuable input toward the design and application of reinforced engineering.

Mechanical Properties of Bentonite-Sand Mixtures Under Triaxial Stress Condition

1994 ◽  
Vol 353 ◽  
Author(s):  
M. Umedera ◽  
A. Fujiwara ◽  
N. Yasufuku ◽  
M. Hyodo ◽  
H. Murata
Keyword(s):  
Mechanical Properties ◽  
Shear Strength ◽  
Water Content ◽  
Triaxial Compression ◽  
Confining Pressure ◽  
Strength Properties ◽  
Compression Tests ◽  
Optimum Water Content ◽  
Triaxial Compression Tests ◽  
Optimum Water

AbstractA series of triaxial compression tests is being conducted under the drained condition on bentonite and sand mixtures, known as buffer, in saturated and optimum water content states to clarify the mechanical properties of the buffer.It was found that the mechanical properties of bentonite and sand mixtures are strongly influenced by water and bentonite contents: shear strength in a saturated state is less than that in an optimum water content state; shear strength decreases rapidly with increasing bentonite content. Strength properties are much dependent on confining pressure.

scholarly journals Analysis of Failure Characteristics and Strength Criterion of Coal-Rock Combined Body with Different Height Ratios

2020 ◽  
Vol 2020 ◽  
pp. 1-14
Author(s):  
Tuo Wang ◽  
Zhanguo Ma ◽  
Peng Gong ◽  
Ning Li ◽  
Shixing Cheng
Keyword(s):  
Shear Failure ◽  
Underground Mining ◽  
Triaxial Compression ◽  
Peak Stress ◽  
Strength Criterion ◽  
Confining Pressure ◽  
Experimental Results ◽  
Compression Tests ◽  
Rock Body ◽  
Coal Rock

In underground mining and roadway support engineering of coal mine, the coal and rock layers bear loads together; therefore, the deformation and mechanical characteristics of the coal-rock combined bodies are not the same as those of the pure coal or rock bodies. In this paper, conventional triaxial compression tests of coal-rock combined bodies with different height ratios were conducted. And the stress and deformation characteristics of coal-rock combined body were studied and the experimental results were analyzed with different strength criteria. The results show that the peak stress, elastic modulus, and strength reduction coefficient of coal-rock combined body are negatively correlated with the ratio of coal to coal-rock combination height and positively correlated with the confining pressure; the coal-rock combination shows obvious ductility under 10 MPa confining pressure. Under the conventional triaxial condition, the shear failure was the main cause of the lateral deformation of the coal body in the coal-rock combination, which was much larger than that of the rock body. The circle deformation value, volume strain value, and the deformation rate in the postpeak stage of coal-rock combination are much higher than those in the prepeak stage. Mohr–Coulomb and general Hoek–Brown strength criterion fit the experimental results well.

Prefabricated Structures Surface Marble Rheological Tests and Constitutive Model Analysis

2014 ◽  
Vol 501-504 ◽  
pp. 419-425
Author(s):  
Qing Xu ◽  
Jiang Da He ◽  
Hong Qiang Xie ◽  
Ming Li Xiao ◽  
Jian Feng Liu
Keyword(s):  
Mechanical Properties ◽  
Rheological Properties ◽  
Flow Rate ◽  
Axial Stress ◽  
Triaxial Compression ◽  
Confining Pressure ◽  
Rheological Parameters ◽  
Structural Plane ◽  
High Confining Pressure ◽  
Confining Pressures

The mechanical properties of intact rock and rock containing structural plane are very different. From the diversion tunnel of Jinping deep rock site to retrieve the complete block of marble, after a high confining pressure triaxial compression simulation tectonic movements, the formation of structural plane, it represents the mechanical properties of the original rock. On the surface of the marble structure containing triaxial compression creep tests, the results showed: at low confining pressure, the weak marble surface as micro-damage accumulation, the emergence of non-uniform partial destruction, while at high confining pressure, creep curve better continuity and integrity; different confining pressures, marble initial rheology and stability both appear rheological phase, accelerated phase rheological obvious; different confining pressures, the same stage of the axial stress steady flow rate compared with the confining pressure increases, the axial steady state flow rate becomes smaller; marble under test showed the rheological properties, the use of Nishihara model can better demonstrate the rheological properties and determine the rheological parameters for other practical engineering reference.

scholarly journals Experimental Study on the Mechanical Properties and Seepage Characteristics of Red Sandstone with a Single Persistent Joint under Triaxial Compression

Geofluids ◽  
2021 ◽  
Vol 2021 ◽  
pp. 1-13
Author(s):  
Wei Wang ◽  
Shifan Liu ◽  
Chong Shi ◽  
Shanxi Zheng ◽  
Qizhi Zhu
Keyword(s):  
Mechanical Properties ◽  
Pore Pressure ◽  
Failure Modes ◽  
Shear Failure ◽  
Triaxial Compression ◽  
Confining Pressure ◽  
Strengthening Effect ◽  
Red Sandstone ◽  
Inclination Angles ◽  
Seepage Characteristics

In this research, the conventional triaxial compression experiments for intact red sandstone specimens and the specimens with a single persistent joint at different inclination angles, i.e., 0°, 30°, 45°, and 90°, were conducted at first. Based on the results of the conventional tests, the effects of the confining pressure and the joint inclination angle on the mechanical properties including deformation behavior and strength parameters were summarized and analyzed, respectively. We find that the strength and deformation of jointed red sandstone are enlarged due to the increment of confining pressure, and the mechanical parameters of specimens show a U-shaped development with the rise of the joint angle. Besides, to investigate the effects of the pore pressure on seepage characteristics of rocks with joint angles at 0°, 45°, and 90°, a series of triaxial compression drainage tests on the jointed red sandstone were performed. The results show that the pore pressure has a weakening effect on the strength of jointed specimens, which can reduce the strengthening effect induced by confining pressure. Meanwhile, the tested specimens mostly present shear failure modes. As a result, the mechanical responses, seepage characteristics, and cracking modes in red sandstone containing a single persistent joint under triaxial compression are revealed.

Experimental Research of Fine Sandstone Strength and Deformation Characteristics under Different Confining and Hydraulic Pressure

2013 ◽  
Vol 353-356 ◽  
pp. 562-570 ◽  
Author(s):  
Zai Bin Liu
Keyword(s):  
Rock Strength ◽  
Pore Water Pressure ◽  
Water Pressure ◽  
Triaxial Compression ◽  
Confining Pressure ◽  
Hydraulic Pressure ◽  
Compression Tests ◽  
Exponential Relationship ◽  
Sandstone Rock ◽  
Strength And Deformation

In order to study sandstone rock strength and deformation parameters under pore water pressure conditions, triaxial compression tests of different hydraulic pressure were executed. Fitting equations of fine sandstone confining pressure and hydraulic pressure coupling effects were established. This research show that fine sandstone rock strength increases with confining pressure increases. Rock mass strength and cohesion have negative exponential relationship with hydraulic pressure. When the hydraulic pressure is 3MPa, elasticity and confining pressure fit to logarithmic relationship. Fine sandstone Elasticity modulus decreases with hydraulic pressure increases. Poisson’s ration and hydraulic pressure fit to linear relationship.

Sign in / Sign up

Export Citation Format

Share Document