High Thermoelectric Performance of p-Type Bi0.5Sb1.5Te3+xTe Crystals Prepared via Gradient Freezing

2012 ◽  
Vol 621 ◽  
pp. 167-171
Author(s):  
Tao Hua Liang ◽  
Shi Qing Yang ◽  
Zhi Chen ◽  
Qing Xue Yang
Keyword(s):  
Thermal Conductivity ◽  
Seebeck Coefficient ◽  
Carrier Concentration ◽  
Thermoelectric Properties ◽  
Figure Of Merit ◽  
Room Temperature ◽  
Thermoelectric Performance ◽  
Thermoelectric Figure Of Merit ◽  
Thermoelectric Figure ◽  
P Type

p-type Bi0.5Sb1.5Te3+xTe thermoelectric crystals with various percentages of Te (x = 0.00 wt.%–3.00 wt.%) excess were prepared by the gradient freeze method. By doping with different Te contents, anti-site defects, Te vacancies and hole carrier concentrations were controlled. The Seebeck coefficient, resistivity, thermal conductivity, carrier concentration, and mobility were measured. The relationships between the Te content and thermoelectric properties were investigated in detail. The results suggested that the thermoelectric figure of merit ZT of the Bi0.5Sb1.5Te3+0.09wt.% crystals was 1.36 near room temperature, the optimum carrier concentration was 1.25 × 1019 cm-3, and the mobility was 1480 cm2 V-1 S-1, respectively.

Thermoelectric Properties of Ni Doped P-Type BiCuSeO Oxyselenides

2014 ◽  
Vol 602-603 ◽  
pp. 906-909 ◽  
Author(s):  
Yao Chun Liu ◽  
Jun Fu Liu ◽  
Bo Ping Zhang ◽  
Yuan Hua Lin
Keyword(s):  
Thermal Conductivity ◽  
Electrical Conductivity ◽  
Seebeck Coefficient ◽  
Thermoelectric Properties ◽  
Figure Of Merit ◽  
Layer Structure ◽  
Thermoelectric Figure Of Merit ◽  
Ni Doping ◽  
Thermoelectric Figure ◽  
P Type

We report on the effect of Ni doping on the thermoelectric properties of p-type BiCuSeO oxyselenide, with layer structure composed of conductive (Cu2Se2)2-layers alternately stacked with insulating (Bi2O2)2+layers along c axis. After doping with Ni, enhanced electrical conductivity coupled with a moderate Seebeck coefficient leads to a power factor of ~231 μwm-1K-2at 873 K. Coupled to low thermal conductivity, ZT at 873 K is increased from 0.35 for pristine BiCuSeO to 0.39 for Bi0.95Ni0.05CuSeO. However, the efficiency of Ni doping in the insulating (Bi2O2)2+layer is low, and this doping only leads to a limited increase of the hole carriers concentration. Therefore Ni doped BiCuSeO has relatively low electrical conductivity which makes its thermoelectric figure of merit much lower than that of Ca, Sr, Ba and Pb doped BiCuSeO.

Thermoelectric Properties of Semiconducting Intermetallic Compounds: FeGa3and RuGa3

2003 ◽  
Vol 793 ◽  
Author(s):  
Y. Amagai ◽  
A. Yamamoto ◽  
C. H. Lee ◽  
H. Takazawa ◽  
T. Noguchi ◽  
...  
Keyword(s):  
Thermal Conductivity ◽  
Electrical Resistivity ◽  
High Temperature ◽  
Seebeck Coefficient ◽  
Transport Properties ◽  
Figure Of Merit ◽  
Room Temperature ◽  
Thermoelectric Figure Of Merit ◽  
Thermoelectric Figure ◽  
High Seebeck Coefficient

ABSTRACTWe report transport properties of polycrystalline TMGa3(TM = Fe and Ru) compounds in the temperature range 313K<T<973K. These compounds exhibit semiconductorlike behavior with relatively high Seebeck coefficient, electrical resistivity, and Hall carrier concentrations at room temperature in the range of 1017- 1018cm−3. Seebeck coefficient measurements reveal that FeGa3isn-type material, while the Seebeck coefficient of RuGa3changes signs rapidly from large positive values to large negative values around 450K. The thermal conductivity of these compounds is estimated to be 3.5Wm−1K−1at room temperature and decreased to 2.5Wm−1K−1for FeGa3and 2.0Wm−1K−1for RuGa3at high temperature. The resulting thermoelectric figure of merit,ZT, at 945K for RuGa3reaches 0.18.

Thermoelectric Properties of CoSb3-based Skutterudite Compounds

2010 ◽  
Vol 1267 ◽  
Author(s):  
Adul Harnwunggmoung ◽  
Ken Kurosaki ◽  
Hiroaki Muta ◽  
Shinsuke Yamanaka
Keyword(s):  
Thermal Conductivity ◽  
Thermoelectric Properties ◽  
Figure Of Merit ◽  
Room Temperature ◽  
Lattice Thermal Conductivity ◽  
Filling Ratio ◽  
Thermoelectric Figure Of Merit ◽  
Thermoelectric Figure ◽  
Alloy Scattering ◽  
Skutterudite Compound

AbstractCoSb3 is known as a skutterudite compound that could exhibit high thermoelectric figure of merit. However, the thermal conductivity of CoSb3 is relatively high. In order to enhance the thermoelectric performance of this compound, we tried to reduce the thermal conductivity of CoSb3 by substitution of Rh for Co and by Tl-filling into the voids. The polycrystalline samples of (Co,Rh)Sb3 and Tl-filled CoSb3 were prepared and the thermoelectric properties such as the Seebeck coefficient, electrical resistivity, and thermal conductivity were measured in the temperature range from room temperature to 750 K. The Rh substitution for Co reduced the lattice thermal conductivity, due to the alloy scattering effect. The minimum value of the lattice thermal conductivity was 4 Wm-1K-1 at 750 K obtained for (Co0.7Rh0.3)Sb3. Also the lattice thermal conductivity rapidly decreased with increasing the Tl-filling ratio. T10.25Co4Sb12 exhibited the best ZT values; the maximum ZT was 0.9 obtained at 600 K.

Enhancement of Thermopower due to Deficiency of Sb in FeSb2

2013 ◽  
Vol 665 ◽  
pp. 179-181 ◽  
Author(s):  
Anup V. Sanchela ◽  
Varun Kushwaha ◽  
Ajay. D. Thakur ◽  
C.V. Tomy
Keyword(s):  
Thermal Conductivity ◽  
Seebeck Coefficient ◽  
Low Temperatures ◽  
Figure Of Merit ◽  
Room Temperature ◽  
Parent Compound ◽  
Thermoelectric Figure Of Merit ◽  
Thermoelectric Figure ◽  
Thermoelectric Power Factor ◽  
Anomalous Peak

FeSb2 was recently found to be a narrow-gap semiconductor with strong electronelectron correlation and a large thermopower at low temperatures. We report measurements of the electrical resistivity, Seebeck coefficient and thermal conductivity between 5 K to 300 K on polycrystalline samples of FeSb2 and FeSb1.9. We found that the deficiency of Sb in the parent compound leads to a giant anomalous peak in thermopower (S) at low temperatures, reaching ~ 426 μV/K at 20 K, resulting in a high thermoelectric power factor at low temperatures, achieving 10 μW/K2m at 27 K.. Consequently, a significantly enhanced thermoelectric figure of merit ZT ~ 0.0015 is achieved near room temperature. At low temperatures there is no improvement in ZT values due to the high thermal conductivity (phonon dominant region). Keywords: Seebeck coefficient, thermal conductivity, resistivity, thermoelectric figure of merit. PACS: 72.20.Pa, 71.27.+a, 71.28.+d

THERMOELECTRIC PROPERTIES OF n-TYPE Bi2Te3–Bi2Se3 ALLOYS

1967 ◽  
Vol 45 (11) ◽  
pp. 3611-3626 ◽  
Author(s):  
C. H. Champness ◽  
W. B. Muir ◽  
P. T. Chiang
Keyword(s):  
Thermal Conductivity ◽  
Carrier Concentration ◽  
Figure Of Merit ◽  
Room Temperature ◽  
Composition Range ◽  
Energy Gap ◽  
Dopant Concentration ◽  
Thermoelectric Figure Of Merit ◽  
Thermoelectric Figure ◽  
Close Relationship

Room temperature measurements of the Seebeck coefficient (α), electrical conductivity (σ), thermal conductivity (κ), and thermoelectric figure of merit (Z) were made on samples of n-type Bi2Te3–Bi2Se3 pseudobinary alloys over the whole composition range. To obtain maximum Z, doping was carried out at each composition by the addition of CuBr (donor) from 0 to 66 mole% Bi2Se3 and by lead and excess Se (acceptors) thereafter. Experimentally determined values of the materials parameter β were found to saturate (β∞) at high conductivity in a given alloy and close relationship was found between β∞ and Zmax The optimized values of σ, κ, and CuBr-dopant concentration were found to show a maximum at 33 mole% Bi2Se3, while the optimized value of α showed a minimum at this composition. These results, together with the fact that no maximum was observed in σ at constant α (i.e., constant carrier concentration), suggest that a maximum in the carrier concentration occurs in optimized material at this composition. Further support for this was provided by the observed variation of σ with α at a given composition which was found to be more consistent with a minimum in the apparent energy gap near 33% Bi2Se3 rather than the maximum reported by other workers.

Influence of multi-sintering on the thermoelectric properties of Bi2Sr2Co2Oy ceramics

2019 ◽  
Vol 34 (02) ◽  
pp. 2050019 ◽  
Author(s):  
Y. Zhang ◽  
M. M. Fan ◽  
C. C. Ruan ◽  
Y. W. Zhang ◽  
X.-J. Li ◽  
...  
Keyword(s):  
Thermal Conductivity ◽  
Thermoelectric Properties ◽  
Figure Of Merit ◽  
Phonon Scattering ◽  
Sintered Sample ◽  
Thermoelectric Figure Of Merit ◽  
Thermoelectric Figure ◽  
The Third ◽  
Ceramic Samples ◽  
Optimum Formula

[Formula: see text] ceramic samples have a structure similar to phonon glass electronic crystals, and their thermoelectric properties can be effectively adjusted through repeated grinding and sintering. The results show that multi-sintering can make their grain refined and increase their grain boundary, which will effectively increase density and phonon scattering. Finally, multi-sintering can reduce the resistivity and thermal conductivity, thus obviously improve thermoelectric figure of merit [Formula: see text] of [Formula: see text]. The optimum [Formula: see text] value of 0.26 is achieved at 923 K by the third sintered sample.

Effects of Ce filling fraction and Fe content on the thermoelectric properties of Co-rich CeyFexCo4−xSb12

2001 ◽  
Vol 16 (3) ◽  
pp. 837-843 ◽  
Author(s):  
Xinfeng Tang ◽  
Lidong Chen ◽  
Takashi Goto ◽  
Toshio Hirai
Keyword(s):  
Thermal Conductivity ◽  
Thermoelectric Properties ◽  
Figure Of Merit ◽  
Single Phase ◽  
Lattice Thermal Conductivity ◽  
Hole Concentration ◽  
Thermoelectric Figure Of Merit ◽  
Thermoelectric Figure ◽  
Filling Fraction ◽  
Fe Content

Single-phase filled skutterudite compounds, CeyFexCo4−xSb12 (x = 0 to 3.0, y = 0 to 0.74), were synthesized by a melting method. The effects of Fe content and Ce filling fraction on the thermoelectric properties of CeyFexCo4−xSb12 were investigated. The lattice thermal conductivity of Ce-saturated CeyFexCo4−xSb12, y being at the maximum corresponding to x, decreased with increasing Fe content (x) and reached its minimum at about x = 1.5. When x was 1.5, lattice thermal conductivity decreased with increasing Ce filling fraction till y = 0.3 and then began to increase after reaching the minimum at y = 0.3. Hole concentration and electrical conductivity of Cey Fe1.5Co2.5Sb12 decreased with increasing Ce filling fraction. The Seebeck coefficient increased with increasing Ce filling fraction. The greatest dimensionless thermoelectric figure of merit T value of 1.1 was obtained at 750 K for the composition of Ce0.28Fe1.52Co2.48Sb12.

The effects of Ge doping on the thermoelectric performance of p-type polycrystalline SnSe

RSC Advances ◽  
2016 ◽  
Vol 6 (115) ◽  
pp. 114825-114829 ◽  
Author(s):  
Tessera Alemneh Wubieneh ◽  
Cheng-Lung Chen ◽  
Pai Chun Wei ◽  
Szu-Yuan Chen ◽  
Yang-Yuan Chen
Keyword(s):  
Figure Of Merit ◽  
Thermoelectric Performance ◽  
Thermoelectric Figure Of Merit ◽  
Thermoelectric Figure ◽  
P Type ◽  
Ge Doping

Ge doping enables to enhance the thermoelectric figure of merit of SnSe..

scholarly journals Термоэлектрические свойства нанокомпозитного Bi-=SUB=-0.45-=/SUB=-Sb-=SUB=-1.55-=/SUB=-Te-=SUB=-2.985-=/SUB=- с микрочастицами SiO-=SUB=-2-=/SUB=-

2019 ◽  
Vol 53 (6) ◽  
pp. 751
Author(s):  
А.А. Шабалдин ◽  
П.П. Константинов ◽  
Д.А. Курдюков ◽  
Л.Н. Лукьянова ◽  
А.Ю. Самунин ◽  
...  
Keyword(s):  
Thermal Conductivity ◽  
Solid Solution ◽  
Electrical Conductivity ◽  
Wide Temperature Range ◽  
Figure Of Merit ◽  
Nanostructured Material ◽  
Thermoelectric Figure Of Merit ◽  
Thermoelectric Efficiency ◽  
Thermoelectric Figure ◽  
P Type

AbstractNanocomposite thermoelectrics based on Bi_0.45Sb_1.55Te_2.985 solid solution of p -type conductivity are fabricated by the hot pressing of nanopowders of this solid solution with the addition of SiO_2 microparticles. Investigations of the thermoelectric properties show that the thermoelectric power of the nanocomposites increases in a wide temperature range of 80–420 K, while the thermal conductivity considerably decreases at 80–320 K, which, despite a decrease in the electrical conductivity, leads to an increase in the thermoelectric efficiency in the nanostructured material without the SiO_2 addition by almost 50% (at 300 K). When adding SiO_2, the efficiency decreases. The initial thermoelectric fabricated without nanostructuring, in which the maximal thermoelectric figure of merit ZT = 1 at 390 K, is most efficient at temperatures above 350 K.

Thermoelectric Properties of n-type (Bi2Se3)x(Bi2Te3)1-x Crystals Prepared by Zone Melting

2008 ◽  
Vol 368-372 ◽  
pp. 547-549
Author(s):  
Jun Jiang ◽  
Ya Li Li ◽  
Gao Jie Xu ◽  
Ping Cui ◽  
Li Dong Chen
Keyword(s):  
Thermal Conductivity ◽  
Electrical Conductivity ◽  
Seebeck Coefficient ◽  
Carrier Concentration ◽  
Thermoelectric Properties ◽  
Figure Of Merit ◽  
Zone Melting ◽  
Chemical Compositions ◽  
Melting Method ◽  
Temperature Range

In the present study, n-type (Bi2Se3)x(Bi2Te3)1-x crystals with various chemical compositions were fabricated by the zone melting method. Thermoelectric properties, including Seebeck coefficient (α), electrical conductivity (σ) and thermal conductivity (κ), were measured in the temperature range of 300-500 K. The influence of the variations of Bi2Te3 and Bi2Se3 content on thermoelectric properties was studied. The increase of Bi2Se3 content (x) caused an increase in carrier concentration and thus an increase of σ and a decrease of α. The maximum figure of merit (ZT = α2σT/κ) of 0.87 was obtained at about 325 K for the composition of 93%Bi2Te3-7%Bi2Se3 with doping TeI4.

Sign in / Sign up

Export Citation Format

Share Document