Potential of Marine Clay as Raw Material in Geopolymer Composite

2012 ◽  
Vol 626 ◽  
pp. 963-966 ◽  
Author(s):  
S.M. Tamizi ◽  
Mohd Mustafa Al Bakri Abdullah ◽  
Kamarudin Hussin ◽  
Che Mohd Ruzaidi Ghazali ◽  
J. Liyana ◽  
...  
Keyword(s):  
Compressive Strength ◽  
Composite Materials ◽  
Sodium Hydroxide ◽  
Sodium Silicate ◽  
Early Time ◽  
Raw Material ◽  
Marine Clay ◽  
Alternative Materials ◽  
Alkaline Activator ◽  
Marine Clays

In this research, marine clays has been studied its potential as a matrix composite materials that tend to be used as alternative materials to concrete. The study shows that marine clays which mixed with appropriate proportion of alkaline activator could have strength requirements for masonry cement. The alkaline activator that been used for the geopolymerisation reaction is sodium silicate and sodium hydroxide. Its compressive strength in early time reached 9-15 MPa.

Study of Manufacture Process and Properties of Tailings and Slag Based Geopolymers

2010 ◽  
Vol 156-157 ◽  
pp. 803-807
Author(s):  
Fu Sheng Niu ◽  
Shan Shan Zhou ◽  
Shu Xian Liu ◽  
Jin Xia Zhang
Keyword(s):  
Compressive Strength ◽  
Sodium Hydroxide ◽  
Sodium Silicate ◽  
Raw Material ◽  
Silicate Concentration ◽  
High Compressive Strength ◽  
Curing Period ◽  
Manufacture Process ◽  
Alkali Activated

The tailings and slag based geopolymers was prepared by sodium silicate, sodium hydroxide alkali-activated tailings and slag. The compressive strength in 7 d under different raw material proportion were tested. The result indicated that tailings and slag based geopolymers has high compressive strength . As the tailings in slag is 80%, the compressive strength in 7d can reach 45.10 MPa . As the Na2SiO3 to NaOH ratio is 0.5, the compressive strength in 7d can reach 63.79 MPa. As the NaOH and sodium silicate concentration in the solution is 35%, the compressive strength in 7d can reach 38.35 MPa respectively; As the curing period is 14 d , the compressive strength can reach 71.25 MPa. As the steel scoria in solid is 20%, the compressive strength in 7d can reach 61.86 MPa respectively.

The Effect of Curing Time on the Properties of Fly Ash-Based Geopolymer Bricks

2012 ◽  
Vol 626 ◽  
pp. 937-941 ◽  
Author(s):  
W.I. Wan Mastura ◽  
H. Kamarudin ◽  
I. Khairul Nizar ◽  
Mohd Mustafa Al Bakri Abdullah ◽  
H. Mohammed
Keyword(s):  
Compressive Strength ◽  
Fly Ash ◽  
Water Absorption ◽  
Sodium Hydroxide ◽  
Sodium Silicate ◽  
Experimental Work ◽  
Base Material ◽  
Curing Time ◽  
Curing Conditions ◽  
Alkaline Activator

This paper reports the results of an experimental work conducted to investigate the effect of curing conditions on the properties of fly ash-based geopolymer bricks prepared by using fly ash as base material and combination of sodium hydroxide and sodium silicate as alkaline activator. The experiments were conducted by varying the curing time in the range of 1-24 hours respectively. The specimens cured for a period of 24 hours have presented the highest compressive strength for all ratio of fly ash to sand. For increasing curing time improve compressive strength and decreasing water absorption.

Flood Mud as Geopolymer Precursor Materials: Effect of Curing Regime on Compressive Strength

2015 ◽  
Vol 815 ◽  
pp. 177-181 ◽  
Author(s):  
Mohd Mustafa Al Bakri Abdullah ◽  
Mukridz Md Mohtar ◽  
Liew Yun Ming ◽  
Muhammad Faheem Mohd Tahir ◽  
Kamarudin Husin ◽  
...  
Keyword(s):  
Compressive Strength ◽  
Sodium Hydroxide ◽  
Sodium Silicate ◽  
Strength Properties ◽  
Sem Analysis ◽  
Raw Material ◽  
Curing Temperature ◽  
Strength Tests ◽  
Maximum Compressive Strength ◽  
Curing Regime

This paper studies the effect of curing temperature and curing duration to the flood mud based geopolymer on compressive strength properties. Flood mud was used as a raw material for geopolymer and geopolymer samples were synthesized by using sodium silicate and sodium hydroxide 14M solution. These samples were cured at different temperature (100°C, 150°C, 200°C and 250°) for different curing duration (6h, 12h and 24h) respectively. Compressive strength tests were carried out at after 28 days. The compressive strength and SEM analysis of geopolymer products were evaluated. Result showed that the maximum compressive strength was 24 MPa at temperature of 150°C for 24 hours. With increasing ageing day, densification of geopolymer gel was observed.

scholarly journals Effect of sodium hydroxide concentration on the compressive strength of geopolymer mortar using fly ash PLTU Tanjungjati B Jepara

2022 ◽  
Vol 955 (1) ◽  
pp. 012010
Author(s):  
A Kustirini ◽  
Antonius ◽  
P Setiyawan
Keyword(s):  
Compressive Strength ◽  
Fly Ash ◽  
Sodium Hydroxide ◽  
Sodium Silicate ◽  
Coal Industry ◽  
Waste Materials ◽  
Geopolymer Concrete ◽  
Sodium Hydroxide Concentration ◽  
Alkaline Activator ◽  
Maximum Compressive Strength

Abstract Geopolymer concrete is concrete that uses environmentally friendly materials, using fly ash from waste materials from the coal industry as a substitute for cement. To produce geopolymer concrete, an alkaline activator is required, with a mixture of Sodium Hydroxide and Sodium Silicate. This research is an experimental study to determine the effect of variations in the concentration of sodium hydroxide (NaOH) 8 Mol, 10 Mol, 12 Mol, and 14 Mol on the compressive strength of geopolymer concrete. Mortar Geopolymer uses a mixture of 1: 3 for the ratio of fly ash and sand, 2.5: 0.45 for the ratio of sodium silicate and sodium hydroxide as an alkaline solution. The specimens used a cube mold having dimension 5 cm x 5 cm x 5 cm, then tested at 7 days and 28 days. The test resulted that concentration of NaOH 12 Mol obtained the maximum compressive strength of geopolymer concrete, that is 38.54 MPa. At concentrations of 12 Mol NaOH and exceeding 12M, the compressive strength of geopolymer concrete decreased.

scholarly journals An experimental study on the mix design optimization of fly ash-based geopolymers

2019 ◽  
Vol 25 (3) ◽  
pp. 259-265
Author(s):  
Evren Arioz ◽  
Omer Arioz ◽  
Mete Kockar
Keyword(s):  
Compressive Strength ◽  
Fly Ash ◽  
Sodium Hydroxide ◽  
Sodium Silicate ◽  
High Strength ◽  
Raw Material ◽  
Mix Design ◽  
Synthesis Conditions ◽  
Alkali Activator ◽  
Design And Synthesis

Geopolymers are materials suitable for utilization in the construction industry due to their superior properties, such as high strength and good durability. The properties of geopolymers can be configured due to mix design and synthesis conditions. In this study, the mix designs providing the highest compressive strength were investigated. For this purpose the sodium hydroxide/sodium silicate ratios and alkali activator/fly ash ratios were differentiated in the geopolymer synthesis. Fly ash was used as raw material. Geopolymer samples were cured at 80?C for 16 h and aged for 7 and 28 days in laboratory. The highest compressive strength was obtained as 27.36 MPa with alkali activator/fly ash ratio of 0.4 and sodium hydroxide/sodium silicate ratio of 1.0. The degree of reaction values were determined for all the geopolymer samples. Fourier Transform infrared spectroscopy (FTIR) was used for determining the chemical bonds in the structure. The spectrum of the samples revealed that more aluminosilicate gel formed for the sample providing the highest compressive strength.

Correlation between Na2SiO3/NaOH Ratio and Fly Ash/Alkaline Activator Ratio to the Strength of Geopolymer

2011 ◽  
Vol 341-342 ◽  
pp. 189-193 ◽  
Author(s):  
Mohd Mustafa Al Bakri Abdullah ◽  
H. Kamarudin ◽  
I. Khairul Nizar ◽  
M. Bnhussain ◽  
Y. Zarina ◽  
...  
Keyword(s):  
Compressive Strength ◽  
Fly Ash ◽  
Sodium Hydroxide ◽  
Sodium Silicate ◽  
Aluminosilicate Gel ◽  
Alkaline Activator ◽  
Maximum Compressive Strength

Geopolymer requires an alkaline activator to induce it pozzolanic property and to accelerate the geopolymerisation process. The geopolymerisation process occurs due to the mixing of fly ash, sodium silicate and sodium hydroxide as the alkaline activator, which produces aluminosilicate gel that acts as a binder. As such, the ratios of fly ash to alkaline activator and Na2SiO3/NaOH play an important role in obtaining desirable compressive strength; the concentration of NaOH used in this study was 12 M. Different ratios of fly ash to alkaline activator (0.5, 1.0, 1.5, 2.0, 2.5 and 3.0) and Na2SiO3/NaOH (0.5, 1.0, 1.5, 2.0, 2.5 and 3.0) were investigated in order to determine the maximum compressive strength. The alkaline activator was mixed with fly ash with different ratio as mentioned above and the samples were cured at 70°C for 24 hours and tested on the seventh day. The maximum compressive strength was obtained when the ratios of fly ash to alkaline activator and Na2SiO3/NaOH were 2.0 and 2.5 with compressive strength 73.86 MPa.

Microstructure Studies on Different Types of Geopolymer Materials

2013 ◽  
Vol 421 ◽  
pp. 384-389 ◽  
Author(s):  
A.M. Mustafa Al Bakri ◽  
Md Tahir Muhammad Faheem ◽  
Andrei Victor Sandhu ◽  
A. Alida ◽  
Mohd Arif Anuar Mohd Salleh ◽  
...  
Keyword(s):  
Fly Ash ◽  
Sodium Hydroxide ◽  
Sodium Silicate ◽  
Room Temperature ◽  
Ordinary Portland Cement ◽  
Raw Materials ◽  
Raw Material ◽  
Binding Material ◽  
Different Types ◽  
Alkaline Activator

Geopolymer is a new binding material produced to substitute the ordinary Portland cement (OPC) function as a binder in concrete. As we know, different types of geopolymer will have different properties. In this research, the different types of geopolymer raw materials had been studied in term of microstructure. Different type of materials which is fly ash (class F) and kaolin had been mixed with alkaline solution consist of sodium silicate and sodium hydroxide with suitable geopolymer raw material to alkaline activator and sodium silicate to sodium hydroxide ratios. The geopolymer samples with different types of raw material were then cured at a temperature 70°C for 24 hr and maintained at room temperature until the testing was conducted. After the geopolymers were aged for seven days, the testing was conducted.

Performances of Artificial Lightweight Geopolymer Aggregate (ALGA) in OPC Concrete

2016 ◽  
Vol 673 ◽  
pp. 29-35 ◽  
Author(s):  
R.A. Razak ◽  
Mohd Mustafa Al Bakri Abdullah ◽  
Kamarudin Hussin ◽  
Khairul Nizar Ismail ◽  
D. Hardjito ◽  
...  
Keyword(s):  
Mechanical Properties ◽  
Compressive Strength ◽  
Water Absorption ◽  
Sodium Hydroxide ◽  
Sodium Silicate ◽  
Lightweight Concrete ◽  
Lightweight Aggregate ◽  
High Volume ◽  
Alkaline Activator ◽  
Geopolymer Paste

The non-availability of natural lightweight aggregate and demand are increasing in worldwide, thus new alternatives on producing artificial aggregate should be developed. This paper discussed on the mechanical properties of artificial lightweight geopolymer aggregate (ALGA) made from LUSI mud and alkaline activator in concrete. LUSI means Sidoarjo mud from Indonesia which erupted on 2006 with high volume and impacted an area of almost 770 hectare. The alkaline activator used was combination of sodium hydroxide and sodium silicate. The geopolymer paste formed need to be pelleted and sintered at 950 °C. The results showed that the compressive strength of OPC-ALGA concrete is 41.89 MPa at 28 days of testing with a density of 1760.1 kg/m3 which can be classified as lightweight concrete. The water absorption of ALGA concrete is 2.77%.

The Effect of Dry Mix Sodium Hydroxide onto Workability and Compressive Strength of Geopolymer Paste

2020 ◽  
Vol 12 (9) ◽  
Author(s):  
A. Z. Mohd Ali ◽  
◽  
N. A. Jalaluddin ◽  
N. Zulkiflee ◽  
◽  
...  
Keyword(s):  
Compressive Strength ◽  
Fly Ash ◽  
Sodium Hydroxide ◽  
Sodium Silicate ◽  
Alkaline Solution ◽  
High Emission ◽  
New Material ◽  
Curing Regime ◽  
Solid Form ◽  
Geopolymer Paste

The production of ordinary Portland cement (OPC) consumes considerable amount of natural resources, energy and at the same time contribute in high emission of CO2 to the atmosphere. A new material replacing cement as binder called geopolymer is alkali-activated concrete which are made from fly ash, sodium silicate and sodium hydroxide (NaOH). The alkaline solution mixed with fly ash producing alternative binder to OPC binder in concrete named geopolymer paste. In the process, NaOH was fully dissolved in water and cooled to room temperature. This study aims to eliminate this process by using NaOH in solid form together with fly ash before sodium silicate liquid and water poured into the mixture. The amount of NaOH solids were based on 10M concentration. The workability test is in accordance to ASTM C230. Fifty cubic mm of the geopolymer paste were prepared which consists of fly ash to alkaline solution ratio of 1: 0.5 and the curing regime of 80℃ for 24 hours with 100% humidity were implemented. From laboratory test, the workability of dry method geopolymer paste were decreased. The compressive strength of the dry mix of NaOH showed 55% and the workability has dropped to 58.4%, it showed strength reduction compared to the wet mix method.

Correlation between Na2SiO3/NaOH and NaOH Molarity to Flexural Strength of Geopolymer Ceramic

2015 ◽  
Vol 754-755 ◽  
pp. 152-156 ◽  
Author(s):  
Nur Ain Jaya ◽  
Mohd Mustafa Al Bakri Abdullah ◽  
Che Mohd Ruzaidi Ghazali ◽  
M. Binhussain ◽  
Kamarudin Hussin ◽  
...  
Keyword(s):  
Elevated Temperature ◽  
Flexural Strength ◽  
Sodium Hydroxide ◽  
Sodium Silicate ◽  
Alkali Activation ◽  
M 12 ◽  
Alkaline Activator

Clay based geopolymer ceramic were produced through the geopolymerisation process by the alkali activation of kaolin with an activator solution which is mixture of sodium silicate and sodium hydroxide and undergoes heating at elevated temperature. The concentration of NaOH used in this study was in the range of 6 M-12 M. The ratio of kaolin to alkaline activator used is 1.0. Three different ratios of Na2SiO3/NaOH of 0.16, 0.24 and 0.32 were used to investigate the optimum flexural strength. The samples were cured at 80 °C for 24 hours and sintered at temperatures ranging from 900 °C-1200 °C. The optimum flexural strength of 86.833 MPa is obtained when the ratios of Na2SiO3/NaOH is 0.24 with the NaOH concentration of 12M at 1200 °C.

Sign in / Sign up

Export Citation Format

Share Document