The Effect of Curing Time on the Properties of Fly Ash-Based Geopolymer Bricks

2012 ◽  
Vol 626 ◽  
pp. 937-941 ◽  
Author(s):  
W.I. Wan Mastura ◽  
H. Kamarudin ◽  
I. Khairul Nizar ◽  
Mohd Mustafa Al Bakri Abdullah ◽  
H. Mohammed
Keyword(s):  
Compressive Strength ◽  
Fly Ash ◽  
Water Absorption ◽  
Sodium Hydroxide ◽  
Sodium Silicate ◽  
Experimental Work ◽  
Base Material ◽  
Curing Time ◽  
Curing Conditions ◽  
Alkaline Activator

This paper reports the results of an experimental work conducted to investigate the effect of curing conditions on the properties of fly ash-based geopolymer bricks prepared by using fly ash as base material and combination of sodium hydroxide and sodium silicate as alkaline activator. The experiments were conducted by varying the curing time in the range of 1-24 hours respectively. The specimens cured for a period of 24 hours have presented the highest compressive strength for all ratio of fly ash to sand. For increasing curing time improve compressive strength and decreasing water absorption.

Effect of Curing Conditions on the Mechanical Properties of Fly Ash-Based Geopolymer without Sodium Silicate Solution

2014 ◽  
Vol 699 ◽  
pp. 15-19 ◽  
Author(s):  
Rosniza Hanim Abdul Rahim ◽  
Khairun Azizi Azizli ◽  
Zakaria Man ◽  
Muhd Fadhil Nuruddin
Keyword(s):  
Compressive Strength ◽  
Elevated Temperature ◽  
Fly Ash ◽  
Sodium Hydroxide ◽  
Sodium Silicate ◽  
Room Temperature ◽  
Sodium Silicate Solution ◽  
Silicate Solution ◽  
Curing Temperature ◽  
Curing Time

Geopolymer is associated with the alkali activation of materials rich in Si and Al, and alkali activator such as sodium hydroxide is used for the dissolution of raw material with the addition of sodium silicate solution to increase the dissolution process. However, the trend of strength development of geopolymer using sodium hydroxide alone is not well established. This paper presents an evaluation on compressive strength of fly ash–based geopolymer by varying curing time with respect to different curing temperature using sodium hydroxide as the only activator. The samples were cured at room temperature and at an elevated temperature (60°C). Further analysis on the microstructure of geopolymer products cured at 60°C was carried out using Field Emission Scanning Microscopy (FESEM). It can be observed that the compressive strength increased as the curing time increased when cured at room temperature; whereas at elevated temperature, the strength increased up to a maximum 65.28 MPa at 14 days but gradually decreased at longer curing time. Better compressive strength can be obtained when the geopolymer was cured at an elevated temperature compared to curing at room temperature.

scholarly journals Effect of sodium hydroxide concentration on the compressive strength of geopolymer mortar using fly ash PLTU Tanjungjati B Jepara

2022 ◽  
Vol 955 (1) ◽  
pp. 012010
Author(s):  
A Kustirini ◽  
Antonius ◽  
P Setiyawan
Keyword(s):  
Compressive Strength ◽  
Fly Ash ◽  
Sodium Hydroxide ◽  
Sodium Silicate ◽  
Coal Industry ◽  
Waste Materials ◽  
Geopolymer Concrete ◽  
Sodium Hydroxide Concentration ◽  
Alkaline Activator ◽  
Maximum Compressive Strength

Abstract Geopolymer concrete is concrete that uses environmentally friendly materials, using fly ash from waste materials from the coal industry as a substitute for cement. To produce geopolymer concrete, an alkaline activator is required, with a mixture of Sodium Hydroxide and Sodium Silicate. This research is an experimental study to determine the effect of variations in the concentration of sodium hydroxide (NaOH) 8 Mol, 10 Mol, 12 Mol, and 14 Mol on the compressive strength of geopolymer concrete. Mortar Geopolymer uses a mixture of 1: 3 for the ratio of fly ash and sand, 2.5: 0.45 for the ratio of sodium silicate and sodium hydroxide as an alkaline solution. The specimens used a cube mold having dimension 5 cm x 5 cm x 5 cm, then tested at 7 days and 28 days. The test resulted that concentration of NaOH 12 Mol obtained the maximum compressive strength of geopolymer concrete, that is 38.54 MPa. At concentrations of 12 Mol NaOH and exceeding 12M, the compressive strength of geopolymer concrete decreased.

Correlation between Na2SiO3/NaOH Ratio and Fly Ash/Alkaline Activator Ratio to the Strength of Geopolymer

2011 ◽  
Vol 341-342 ◽  
pp. 189-193 ◽  
Author(s):  
Mohd Mustafa Al Bakri Abdullah ◽  
H. Kamarudin ◽  
I. Khairul Nizar ◽  
M. Bnhussain ◽  
Y. Zarina ◽  
...  
Keyword(s):  
Compressive Strength ◽  
Fly Ash ◽  
Sodium Hydroxide ◽  
Sodium Silicate ◽  
Aluminosilicate Gel ◽  
Alkaline Activator ◽  
Maximum Compressive Strength

Geopolymer requires an alkaline activator to induce it pozzolanic property and to accelerate the geopolymerisation process. The geopolymerisation process occurs due to the mixing of fly ash, sodium silicate and sodium hydroxide as the alkaline activator, which produces aluminosilicate gel that acts as a binder. As such, the ratios of fly ash to alkaline activator and Na2SiO3/NaOH play an important role in obtaining desirable compressive strength; the concentration of NaOH used in this study was 12 M. Different ratios of fly ash to alkaline activator (0.5, 1.0, 1.5, 2.0, 2.5 and 3.0) and Na2SiO3/NaOH (0.5, 1.0, 1.5, 2.0, 2.5 and 3.0) were investigated in order to determine the maximum compressive strength. The alkaline activator was mixed with fly ash with different ratio as mentioned above and the samples were cured at 70°C for 24 hours and tested on the seventh day. The maximum compressive strength was obtained when the ratios of fly ash to alkaline activator and Na2SiO3/NaOH were 2.0 and 2.5 with compressive strength 73.86 MPa.

Performances of Artificial Lightweight Geopolymer Aggregate (ALGA) in OPC Concrete

2016 ◽  
Vol 673 ◽  
pp. 29-35 ◽  
Author(s):  
R.A. Razak ◽  
Mohd Mustafa Al Bakri Abdullah ◽  
Kamarudin Hussin ◽  
Khairul Nizar Ismail ◽  
D. Hardjito ◽  
...  
Keyword(s):  
Mechanical Properties ◽  
Compressive Strength ◽  
Water Absorption ◽  
Sodium Hydroxide ◽  
Sodium Silicate ◽  
Lightweight Concrete ◽  
Lightweight Aggregate ◽  
High Volume ◽  
Alkaline Activator ◽  
Geopolymer Paste

The non-availability of natural lightweight aggregate and demand are increasing in worldwide, thus new alternatives on producing artificial aggregate should be developed. This paper discussed on the mechanical properties of artificial lightweight geopolymer aggregate (ALGA) made from LUSI mud and alkaline activator in concrete. LUSI means Sidoarjo mud from Indonesia which erupted on 2006 with high volume and impacted an area of almost 770 hectare. The alkaline activator used was combination of sodium hydroxide and sodium silicate. The geopolymer paste formed need to be pelleted and sintered at 950 °C. The results showed that the compressive strength of OPC-ALGA concrete is 41.89 MPa at 28 days of testing with a density of 1760.1 kg/m3 which can be classified as lightweight concrete. The water absorption of ALGA concrete is 2.77%.

The Effect of Dry Mix Sodium Hydroxide onto Workability and Compressive Strength of Geopolymer Paste

2020 ◽  
Vol 12 (9) ◽  
Author(s):  
A. Z. Mohd Ali ◽  
◽  
N. A. Jalaluddin ◽  
N. Zulkiflee ◽  
◽  
...  
Keyword(s):  
Compressive Strength ◽  
Fly Ash ◽  
Sodium Hydroxide ◽  
Sodium Silicate ◽  
Alkaline Solution ◽  
High Emission ◽  
New Material ◽  
Curing Regime ◽  
Solid Form ◽  
Geopolymer Paste

The production of ordinary Portland cement (OPC) consumes considerable amount of natural resources, energy and at the same time contribute in high emission of CO2 to the atmosphere. A new material replacing cement as binder called geopolymer is alkali-activated concrete which are made from fly ash, sodium silicate and sodium hydroxide (NaOH). The alkaline solution mixed with fly ash producing alternative binder to OPC binder in concrete named geopolymer paste. In the process, NaOH was fully dissolved in water and cooled to room temperature. This study aims to eliminate this process by using NaOH in solid form together with fly ash before sodium silicate liquid and water poured into the mixture. The amount of NaOH solids were based on 10M concentration. The workability test is in accordance to ASTM C230. Fifty cubic mm of the geopolymer paste were prepared which consists of fly ash to alkaline solution ratio of 1: 0.5 and the curing regime of 80℃ for 24 hours with 100% humidity were implemented. From laboratory test, the workability of dry method geopolymer paste were decreased. The compressive strength of the dry mix of NaOH showed 55% and the workability has dropped to 58.4%, it showed strength reduction compared to the wet mix method.

Physical, Mechanical and Micro-Structural Properties of F Type Fly-Ash Based Geopolymeric Bricks Produced by Pressure Forming Process

2010 ◽  
Vol 69 ◽  
pp. 69-74 ◽  
Author(s):  
Ömer Arıöz ◽  
Kadir Kilinç ◽  
Mustafa Tuncan ◽  
Ahmet Tuncan ◽  
Taner Kavas
Keyword(s):  
Heat Treatment ◽  
Compressive Strength ◽  
Fly Ash ◽  
Sodium Hydroxide ◽  
Sodium Silicate ◽  
Heat Treatment Temperature ◽  
Treatment Duration ◽  
Treatment Temperature ◽  
Alumino Silicate ◽  
Heat Treatment Duration

Geopolymer is a new class of three-dimensionally networked amorphous to semi-crystalline alumino-silicate materials, and first developed by Professor Joseph Davidovits in 1978. Geopolymers can be synthesized by mixing alumino–silicate reactive materials such as kaolin, metakaolin or pozzolans in strong alkaline solutions such as NaOH and KOH and then cured at room temperature. Heat treatment applied at higher temperatures may give better results. Depending on the mixture, the optimum temperature and duration vary 40-100 °C and 2-72 hours, respectively. The properties of geopolymeric paste depend on type of source material (fly ash, metakaolin, kaolin), type of activator (sodium silicate-sodium hydroxide, sodium silicate-potassium hydroxide), amount of activator, heat treatment temperature, and heat treatment duration. In this experimental investigation, geopolymeric bricks were produced by using F-type fly ash, sodium silicate, and sodium hydroxide solution. The bricks were treated at various temperatures for different hours. The compressive strength and density of F-type fly ash based geopolymeric bricks were determined at the ages of 7, 28 and 90 days. Test results have revealed that the compressive strength values of F-type fly ash based geobricks ranged between 5 and 60 MPa. It has been found that the effect of heat treatment temperature and heat treatment duration on the density of F-type fly ash based geobricks was not significant. It should be noted that the spherical particle size increased as the heat treatment temperature increased in the microstructure of F-type fly ash based geobricks treated in oven at the temperature of 60 °C for 24 hours.

scholarly journals Alkali-activated concretes based on fly ash and blast furnace slag: Compressive strength, water absorption and chloride permeability

2020 ◽  
Vol 40 (2) ◽  
Author(s):  
Daniela Eugenia Angulo-Ramírez ◽  
William Gustavo Valencia-Saavedra ◽  
Ruby Mejía de Gutiérrez
Keyword(s):  
Compressive Strength ◽  
Blast Furnace ◽  
Fly Ash ◽  
Water Absorption ◽  
Blast Furnace Slag ◽  
Construction Materials ◽  
Chloride Ion ◽  
Chloride Permeability ◽  
Alkaline Activator ◽  
Furnace Slag

Concretes based on alkaliactivated binders have attracted considerable attention as new alternative construction materials, which can substitute Portland Cement (OPC) in several applications. These binders are obtained through the chemical reaction between an alkaline activator and reactive aluminosilicate materials, also named precursors. Commonly used precursors are fly ash (FA), blast furnace slag (GBFS), and metakaolin. The present study evaluated properties such as compressive strength, rate of water absorption (sorptivity), and chloride permeability in two types of alkaliactivated concretes (AAC): FA/GBFS 80/20 and GBFS/OPC 80/20. OPC and GBFS/OPC* concretes without alkaliactivation were used as reference materials. The highest compressive strength was observed in the FA/GBFS concrete, which reported 26,1% greater strength compared to OPC concrete after 28 days of curing. The compressive strength of alkaliactivated FA/GBFS 80/20 and GBFS/OPC 80/20 was 61 MPa and 42 MPa at 360 days of curing, respectively. These AAC showed low permeability to the chloride ion and a reduced water absorption. It is concluded that these materials have suitable properties for various applications in the construction sector.

Effect of Curing Time and Sintering to the Properties of Geopolymer Mortars

2017 ◽  
Vol 888 ◽  
pp. 184-187
Author(s):  
Salwa Ismail ◽  
Mohammad Faizal Mohd Razali ◽  
Izwan Johari ◽  
Zainal Arifin Ahmad ◽  
Shah Rizal Kasim
Keyword(s):  
Compressive Strength ◽  
Fly Ash ◽  
Distilled Water ◽  
Curing Time ◽  
Pore Former ◽  
X Ray ◽  
Before And After ◽  
Naoh Solution ◽  
Added Water ◽  
Alkaline Activator

In this study, the geopolymer mortars were synthesized with fly ash (FA) and silica powder as aluminosilicate sources and a combination of sodium hydroxide (NaOH) solution, sodium silicate (Na2SiO3) solution and distilled water as alkaline activator. Commercial sago was used as a pore former in the mortars. The percentage of sago used were 10, 20 and 30 wt% of FA. The amount of added water used in each mixture was 5% by weight of FA, NaOH solution and Na2SiO3 solution. The formed geopolymer mortars were cured for 1, 3 and 7 days and sintered at 1000 °C. X-ray fluoresence (XRF) shown that FA contains higher amount of silica (SiO2) and alumina (Al2O3) which is important as aluminosilicate sources. The properties of the geopolymer mortars before and after sintered at 1000 °C have been investigated. The results show that geopolymer mortars with 10% of sago content with curing time of 7 days and sintered at 1000 °C give the highest compressive strength of 13.5 MPa.

scholarly journals Artificial Intelligence Approaches for Prediction of Compressive Strength of Geopolymer Concrete

Materials ◽  
2019 ◽  
Vol 12 (6) ◽  
pp. 983 ◽  
Author(s):  
Dong Dao ◽  
Hai-Bang Ly ◽  
Son Trinh ◽  
Tien-Thinh Le ◽  
Binh Pham
Keyword(s):  
Artificial Intelligence ◽  
Compressive Strength ◽  
Fly Ash ◽  
Sodium Hydroxide ◽  
Sodium Silicate ◽  
Steel Slag ◽  
Sodium Silicate Solution ◽  
Silicate Solution ◽  
Partial Replacement ◽  
Geopolymer Concrete

Geopolymer concrete (GPC) has been used as a partial replacement of Portland cement concrete (PCC) in various construction applications. In this paper, two artificial intelligence approaches, namely adaptive neuro fuzzy inference (ANFIS) and artificial neural network (ANN), were used to predict the compressive strength of GPC, where coarse and fine waste steel slag were used as aggregates. The prepared mixtures contained fly ash, sodium hydroxide in solid state, sodium silicate solution, coarse and fine steel slag aggregates as well as water, in which four variables (fly ash, sodium hydroxide, sodium silicate solution, and water) were used as input parameters for modeling. A total number of 210 samples were prepared with target-specified compressive strength at standard age of 28 days of 25, 35, and 45 MPa. Such values were obtained and used as targets for the two AI prediction tools. Evaluation of the model’s performance was achieved via criteria such as mean absolute error (MAE), root mean square error (RMSE), and coefficient of determination (R2). The results showed that both ANN and ANFIS models have strong potential for predicting the compressive strength of GPC but ANFIS (MAE = 1.655 MPa, RMSE = 2.265 MPa, and R2 = 0.879) is better than ANN (MAE = 1.989 MPa, RMSE = 2.423 MPa, and R2 = 0.851). Sensitivity analysis was then carried out, and it was found that reducing one input parameter could only make a small change to the prediction performance.

Sign in / Sign up

Export Citation Format

Share Document