Fabrication of V-Doped TiO2 Nanoparticles and Photocatalytic Studies under Visible Light

2013 ◽  
Vol 634-638 ◽  
pp. 2180-2183 ◽  
Author(s):  
Jun Bo Guo ◽  
Zhang Hua Gan ◽  
Jing Liu ◽  
Zhi Hong Lu
Keyword(s):  
Visible Light ◽  
Sol Gel ◽  
Synergetic Effect ◽  
X Ray Diffraction ◽  
Electron Hole ◽  
Optimal Doping ◽  
X Ray ◽  
Light Region ◽  
Vis Spectroscopy ◽  
Optimal Doping Concentration

The V-doped TiO2 nanoparticles were successfully prepared by sol-gel method and characterized by X-ray diffraction (XRD), UV-vis spectroscopy and photoluminescence (PL) spectroscopy respectively. It is found that doping V can shift the absorption edge to the visible light region and decrease the recombination of photo-induced electron-hole pairs. Then the photo-absorption and photocatalytic activity were greatly improved. The optimal doping concentration is 0.5% due to synergetic effect of the recombination of electron-hole pairs and adsorption of dyes molecules at the surface of samples.

Influence of Calcination Temperature towards Fe-TiO2 for Visible-Driven Photocatalyst

2017 ◽  
Vol 888 ◽  
pp. 435-440 ◽  
Author(s):  
Siti Aida Ibrahim ◽  
Muhamad Nazim Ahmid
Keyword(s):  
Visible Light ◽  
Calcination Temperature ◽  
Sol Gel ◽  
X Ray Diffraction ◽  
Combined Method ◽  
Calcination Process ◽  
Calcination Temperatures ◽  
Light Region ◽  
Average Grain Size ◽  
Vis Spectroscopy

TiO2 is one of the most promising photocatalysts that is widely used for environmental clean-up due to its ability to degrade organic pollutants in air or water. The purpose of this study is to enhance the photocatalytic activity of TiO2 by absorbing energy in visible light region in order to degrade pollutants. In this study, the nanostructured Fe-TiO2 was successfully synthesised via a combined method of sol-gel and calcination process. The calcination temperatures used varied from 400 to 800 °C. The as-prepared samples were characterized by X-ray diffraction (XRD), FESEM and UV-Vis spectroscopy (UV-Vis). XRD results show that the phases of TiO2 are dependent on calcination temperature. It is found that both TiO2 and Fe-TiO2 phases were transformed from anatase to rutile as the temperatures were increased. FESEM images revealed that the particle size was agglomerated and the average grain size was about 54 to 66 nm. UV-Vis analysis indicated that the incorporation of Fe and varied calcination temperature may affect the optical properties as the absorption profile was shifted from 445 nm to 585 nm. Thus, this results show that Fe-TiO2 is a highly potential photocatalyst to degrade pollutants under visible light irradiation.

Preparation and Photocatalytic Activity of N-TiO2/Sepiolite Nanocomposite

2011 ◽  
Vol 694 ◽  
pp. 85-90
Author(s):  
Dai Mei Chen ◽  
Hai Peng Ji ◽  
Jian Xin Wang ◽  
Jian Chen ◽  
Zheng Ming Wu ◽  
...  
Keyword(s):  
Photocatalytic Activity ◽  
Visible Light ◽  
Photoelectron Spectroscopy ◽  
Sol Gel ◽  
X Ray Diffraction ◽  
Methylene Blue Degradation ◽  
X Ray ◽  
Vis Spectroscopy ◽  
Photocatalytic Reactions ◽  
Nitrogen Contents

To utilize visible light and separate of TiO2 nanoparticles more efficiently in photocatalytic reactions, nitrogen doped TiO2/sepiolite composites (N-TiO2/sep) with different nitrogen contents were prepared by a sol-gel method and characterized by X-ray diffraction (XRD), X-ray photoelectron spectroscopy (XPS) and UV-vis spectroscopy. XRD showed that anatase-TiO2 nanoparticles were loaded on the surface of sepiolite. XPS revealed that N atoms could incorporate into the lattice of anatase TiO2 substituting the sites of oxygen atoms. UV-vis spectroscopy showed that the visible light absorption of N-TiO2/sep samples decreased with the increase of calciantion temperature and increased with the increase of N content. The photocatalytic activities of obtained N-TiO2/sep samples were evaluated by methylene blue degradation under visible light irradiation. It was found that the N-TiO2/sep samples had the higher photocatalytic activity than that of TiO2/sep.

scholarly journals Synthesis and Characterization of Rhodium Doped on TiO2/HCP for Enhanced Photocatalytic Performance on Pentachlorophenol

2014 ◽  
Vol 2014 ◽  
pp. 1-8 ◽  
Author(s):  
Saheed Olalekan Sanni ◽  
Omoruyi Gold Idemudia
Keyword(s):  
Visible Light ◽  
Surface Characterization ◽  
Sol Gel ◽  
Gravimetric Analysis ◽  
X Ray Diffraction ◽  
Sunlight Irradiation ◽  
X Ray ◽  
Light Region ◽  
Visible Spectra

Visible-light-responsive material based on Rhodium doped on titanium dispersed on dealuminated clinoptilolite (TiO2/HCP) was synthesized via a combination of the sol-gel method and photoreductive deposition technique. The photocatalyst surface characterization, structural and optical properties were investigated by X-ray diffraction (XRD), scanning electron microscopy (SEM), energy-dispersive X-ray analysis (EDAX), Fourier transform infrared spectroscopy (FTIR), thermal gravimetric analysis (TGA), and UV-visible spectra (UV-VIS). Doping TiO2/HCP with Rh imparts a red shifting of the absorption band into the visible light region according to UV-VIS. The prepared composite materials were evaluated for their photocatalytic activities on pentachlorophenol (PCP) degradation under sunlight irradiation. The Rhodium doped TiO2/HCP exhibited enhanced photocatalytic activity and can be considered as a potential photocatalyst in wastewater treatment.

Few-Layered MoS2 Nanostructures for Highly Efficient Visible Light Photocatalysis

NANO ◽  
2016 ◽  
Vol 11 (10) ◽  
pp. 1650114 ◽  
Author(s):  
Dan Li ◽  
Jianwei Li ◽  
Caiqin Han ◽  
Xinsheng Zhao ◽  
Haipeng Chu ◽  
...  
Keyword(s):  
Electron Microscopy ◽  
Photocatalytic Activity ◽  
Visible Light ◽  
Electrochemical Impedance ◽  
X Ray Diffraction ◽  
Electron Hole ◽  
Electrochemical Impedance Spectra ◽  
X Ray ◽  
Transmission Electron ◽  
Electron Hole Pair

Few-layered MoS2 nanostructures were successfully synthesized by a simple hydrothermal method without the addition of any catalysts or surfactants. Their morphology, structure and photocatalytic activity were characterized by X-ray diffraction, scanning electron microscopy, energy dispersive X-ray spectroscopy, transmission electron microscopy, electrochemical impedance spectra and UV-Vis absorption spectroscopy, respectively. These results show that the MoS2 nanostructures synthesized at 180[Formula: see text]C exhibit an optimal visible light photocatalytic activity (99%) in the degradation of Rhodamine B owing to the relatively easier adsorption of pollutants, higher visible light absorption and lower electron–hole pair recombination.

Enhanced visible-active photocatalytic behaviors observed in Mn-doped BiFeO3

2018 ◽  
Vol 32 (17) ◽  
pp. 1850185 ◽  
Author(s):  
Yun-Hui Si ◽  
Yu Xia ◽  
Ya-Yun Li ◽  
Shao-Ke Shang ◽  
Xin-Bo Xiong ◽  
...  
Keyword(s):  
Photocatalytic Activity ◽  
Visible Light ◽  
Band Gap ◽  
Diffuse Reflectance Spectroscopy ◽  
X Ray Diffraction ◽  
Electron Hole ◽  
X Ray ◽  
Mn Doped ◽  
Hole Recombination ◽  
Narrow Band Gap Semiconductors

A series of BiFeO3 and BiFe[Formula: see text]Mn[Formula: see text]O3 (x = 0, 0.02, 0.04, 0.06, 0.08, 0.10) were synthesized by a hydrothermal method. The samples were characterized by X-ray diffraction, scanning electron microscopy, energy dispersive spectroscopy (EDS) and UV–Vis diffuse reflectance spectroscopy, and their photocatalytic activity was studied by photocatalytic degradation of methylene blue in aqueous solution under visible light irradiation. The band gap of BiFeO3 was significantly decreased from 2.26 eV to 1.90 eV with the doping of Mn. Furthermore, the 6% Mn-doped BiFeO3 photocatalyst exhibited the best activity with a degradation rate of 94% after irradiation for 100 min. The enhanced photocatalytic activity with Mn doping could be attributed to the enhanced optical absorption, increment of surface reactive sites and reduction of electron–hole recombination. Our results may be conducive to design more efficient photocatalysts responsive to visible light among narrow band gap semiconductors.

Visible-Light-Induced Photocatalytic Activity of Boron-Doped BiVO4

2014 ◽  
Vol 809-810 ◽  
pp. 890-894
Author(s):  
Dan Li ◽  
Lian Wei Shan ◽  
Gui Lin Wang ◽  
Li Min Dong ◽  
Wei Li ◽  
...  
Keyword(s):  
Photocatalytic Activity ◽  
Visible Light ◽  
Diffuse Reflectance ◽  
Diffuse Reflectance Spectroscopy ◽  
Sol Gel ◽  
Reflectance Spectroscopy ◽  
Scheelite Structure ◽  
X Ray Diffraction ◽  
X Ray ◽  
Boron Doped

Boron-BiVO4 samples were synthesized by sol-gel method. They were characterized by UV-vis diffuse reflectance spectroscopy, X-ray diffraction. Photocatalytic activity of the obtained BiVO4 samples was investigated through degrading methylene blue (MB). The results reveal that boron-BiVO4 catalysts have monoclinic scheelite structure. The BiVO4 and Co-BiVO4 photocatalysts were responsive to visible light. Co-BiVO4 photocatalyst showed higher photocatalytic activity than pure BiVO4, resulting in the significantly improved efficiency of degradation of MB.

FeYO3@rGO nanocomposites: Synthesis, characterization and application in photooxidative degradation of atrazine under visible light

2021 ◽  
Vol 11 (5) ◽  
pp. 706-716
Author(s):  
Nada D. Al-Khthami ◽  
Tariq Altalhi ◽  
Mohammed Alsawat ◽  
Mohamed S. Amin ◽  
Yousef G. Alghamdi ◽  
...  
Keyword(s):  
Visible Light ◽  
Photoelectron Spectroscopy ◽  
Sol Gel ◽  
Bandgap Energy ◽  
X Ray Diffraction ◽  
X Ray ◽  
Transmission Electron ◽  
Reduced Graphene ◽  
Structural Surface ◽  
Adsorption Desorption

Different organic pollutants have been remediated photo catalytically by applying perovskite photocatalysts. Atrazine (ATR) is a pesticide commonly detected as a pollutant in drinking, surface and ground water. Herein, FeYO3@rGO heterojunction was synthesized and applied for photooxidation decomposition of ATR. First, FeYO 3nanoparticles (NPs) were prepared via routine sol-gel. After that, FeYO3 NPs were successfully incorporated with different percentages (5, 10, 15 and 20 wt.%) of reduced graphene oxide (rGO) in the synthesis of novel FeYO3@rGO photocatalyst. Morphological, structural, surface, optoelectrical and optical characteristics of constructed materials were identified via X-ray diffraction (XRD), X-ray photoelectron spectroscopy (XPS), Transmission electron microscopy (TEM), adsorption/desorption isotherms, diffusive reflectance (DR) spectra, and photoluminescence response (PL). Furthermore, photocatalytic achievement of the constructed materials was evaluated via photooxidative degradation of ATR. Various investigations affirmed the usefulness of rGO incorporation on the advancement of formed photocatalysts. Actually, novel nanocomposite containing rGO (15 wt.%) possessed diminished bandgap energy, as well as magnified visible light absorption. Furthermore, such nanocomposite presented exceptional photocatalytic achievement when exposed to visible light as ATR was perfectly photooxidized over finite amount (1.6 g · L-1) from the optimized photocatalyst when illuminated for 30 min. The advanced photocatalytic performance of constructed heterojunctions could be accredited mainly to depressed recombination amid induced charges. The constructed FeYO3@rGO nanocomposite is labelled as efficient photocatalyst for remediation of herbicides from aquatic environments.

One-Step Hydrothermal Synthesis of Bi2S3-TiO2-RGO Composites with Enhanced Visible Light Photocatalytic Activities

NANO ◽  
2018 ◽  
Vol 13 (05) ◽  
pp. 1850051 ◽  
Author(s):  
Yanan Li ◽  
Zhongmin Liu ◽  
Yaru Li ◽  
Yongchuan Wu ◽  
Jitao Chen ◽  
...  
Keyword(s):  
Visible Light ◽  
Photocatalytic Degradation ◽  
Photogenerated Electron ◽  
X Ray Diffraction ◽  
Electron Hole ◽  
Photocatalytic Ability ◽  
Transmission Electron ◽  
Light Region ◽  
Infrared Spectrometer ◽  
One Step

The Bi2S3-TiO2-RGO composites were synthesized by a facile one-step hydrothermal method and applied for the photocatalytic degradation of Rhodamine B (Rh B) under the visible light. The Bi2S3-TiO2-RGO composites were characterized by transmission electron microscopy, X-ray diffraction, Raman and Fourier transform infrared spectrometer. The results indicated that the Bi2S3-TiO2-RGO composites were successfully prepared, and Ti-O-C and S-C bonds were existing among Bi2S3, TiO2 as well as RGO. Furthermore, the photocatalytic ability of Bi2S3-TiO2-RGO composites was excellent under visible light due to its responding to the whole visible light region, low recombination rate of photogenerated electron–hole pairs and relatively negative conduction band. Rh B photocatalytic degradation rate was 99.5% after 50[Formula: see text]min and still could reach 98.4% after five cycles. Finally, a formation mechanism as well as a photocatalytic mechanism of Bi2S3-TiO2-RGO composites were proposed based on the experimental results.

Photocatalytic Activity of CuO/ZnO Heterostructure Nanocrystals under UV-Visible Light Irradiation

2014 ◽  
Vol 787 ◽  
pp. 35-40 ◽  
Author(s):  
Xiao Yan Zhou ◽  
Peng Wei Zhou ◽  
Hao Guo ◽  
Bo Yang ◽  
Ru Fei Ren
Keyword(s):  
Photocatalytic Activity ◽  
Visible Light ◽  
Visible Light Irradiation ◽  
Cuo Nanoparticles ◽  
Light Irradiation ◽  
Molar Ratio ◽  
X Ray Diffraction ◽  
X Ray ◽  
Vis Spectroscopy ◽  
Uv Visible

The p-n junction photocatalysts, p-CuO (at. 0-25%)/n-ZnO nanocomposite were prepared through hydrothermal method without using any organic solvent or surfactant. The as-prepared samples were characterized by X-ray diffraction, scanning electron microscopy, energy dispersive X-Ray spectroscopy, and UV-vis spectroscopy. The results demonstrated that the CuO/ZnO nanocomposite presented a two-dimensional morphology composed of sheet-like ZnO nanostructures adorned with CuO nanoparticles. The photocatalytic activity of CuO/ZnO with different Cu/Zn molar rations and pure ZnO synthesized by the identical synthetic route were evaluated by degrading methylene blue (MB) dye under UV-visible light irradiation. The CuO/ZnO with Cu/Zn molar ratio of 4% exhibits the highest photocatalytic activity compared that of the other photocatalysts under the identical conditions. It is mainly attributed to the increased charge separation rate in the nanocomposite and the extended photo-responding range.

Photocatalytic Activity of Bismuth Ferrite Nanoparticles Synthesized via Sol-Gel Route

2019 ◽  
Vol 233 (5) ◽  
pp. 595-607 ◽  
Author(s):  
Mohsin Siddique ◽  
Noor Muhammad Khan ◽  
Muhammad Saeed
Keyword(s):  
Visible Light ◽  
Photocatalytic Degradation ◽  
Irradiation Time ◽  
Bismuth Ferrite ◽  
Sol Gel ◽  
Reaction System ◽  
Light Conditions ◽  
X Ray Diffraction ◽  
Light Region ◽  
Gel Technique

Abstract Nanosized, magnetically separable bismuth ferrite (BFO) nanoparticles, pertaining a crystallite size in the range of 14–15 nm were prepared via facile sol-gel technique. The product was characterized by scanning electron microscopy, X-ray diffraction, and Fourier-transform infrared spectroscopy. The product was explored for the photocatalytic mineralization of rhodamine B (RB) dye in aqueous medium. The effect of different investigational parameters such as amount of photocatalyst, initial dye concentration and irradiation time on the photocatalytic degradation of RB was studied. The results reveal that the catalyst shows good degrading ability under normal pH and visible light conditions. BFO nanoparticles demonstrated a strong absorption ability in the visible-light region, which lead to efficient photocatalytic degradation of RB dye The reaction system was heterogeneous in nature in which the catalyst can be separated by a normal magnet.

Sign in / Sign up

Export Citation Format

Share Document