Structural and optical property studies on Fe doped CuO nanoparticles

The Cupric oxide (CuO) nanostructures and Fe doped CuO nanomaterials are synthesized by microwave irradiation method. The effect of Fe doping on the crystal structure, band gap and optical properties of synthesized samples were characterized by using x-ray diffraction, ultraviolet-visible spectrometer, photoluminescence spectrometer and Fourier transform infrared spectrometer. X-ray diffraction study confirms the size of the particle in nanometer. The optical band gap calculated from UV–Vis absorption spectrum, reveals the change in band gap energy due to the presence of dopants. The photoluminescence spectrum suggests that Fe doped CuO nanoparticles may be used in optoelectronic devices. The functional group analysis carried out by Fourier transform infrared spectroscopy confirmed the substitution of Fe in the samples.

Prussian Blue Analogue Derived Co3O4/CuO Nanoparticles as Effective Oxygen Reduction Reaction Catalyst for Magnesium-Air Battery

Developing efficient, durable, and cost-effective non-noble metal catalysts for oxygen reduction reaction (ORR) is necessary to promote the efficiency and performance of Mg-air batteries. Herein, the Co3O4/CuO nanoparticles were synthesized by a low-cost and simple approach using CuCo-based prussian blue analogue (PBA) as precursor of pyrolysis at different calcination temperatures. It was found that the Co3O4/CuO nanoparticles calcined at 600ºC (CCO-600) have relatively small size and superior ORR performance. The onset potential is 0.889 V and the diffusion limiting current density achieves 6.746 mA·cm-2, as well as prominent stability in 0.1 M KOH electrolyte. The electron transfer number of the CCO-600 is 3.89 under alkaline medium, which indicates that the reaction mechanism of ORR is dominated by 4 e process, similar to commercial Pt. The primary Mg-air battery with the CCO-600 as the cathode catalyst has been assembled and possesses better discharge performance than the CuCo-based PBA. The open circuit voltage of CCO-600 arrives at 1.76 V and energy density of 1895.95 mWh/g. This work provides an effective strategy to develop non-noble metal ORR catalyst for the application of metal-air batteries

Investigation on the effect of CuO nanoparticles on the IFT and wettability alteration at the presence of [C12mim][Cl] during enhanced oil recovery processes

In the current study, the effect of CuO nanoparticles (CuO-NPs) at the presence of dodecyl-3-methylimidazolium chloride ([C12mim][Cl]) is investigated on the interfacial tension (IFT) reduction, wettability alteration, and even tertiary oil recovery. Since the prepared solutions with CuO-NPs are completely dark and it is impossible to measure the IFT of these solutions in the presence of crude oil using the pendant drop method (since one of the phases must be transparent for IFT measurement using the pendant drop method), n-heptane (representative of saturates) and toluene (representative of aromatics) are used only for IFT measurement of solutions prepared by CuO-NPs, while rest of the experiments are performed using crude oil. The obtained results reveal that CuO-NPs are not stable in the aqueous solution in the absence of surfactant which means fast precipitation of CuO-NPs and a high risk of pore plugging. In this way, the stability of CuO-NPs is investigated at the presence of dodecyl-3-methyl imidazolium chloride ([C12mim][Cl]) as an effective surfactant for stabilizing the CuO-NPs in the aqueous solution (more than 1 month without precipitation using 1000 ppm of IL). Further measurements reveal that although the presence of IL in the aqueous solution can reduce the IFT of oil/aqueous solution system, especially for the aqueous solutions prepared by formation brine (0.65 mN.m−1), the presence of CuO-NPs has no considerable effect on the IFT. On the other hand, not only the contact angle (CA) measurements reveal the considerable effect of IL on the wettability alteration toward water-wet condition (68.3° for IL concentration of 1000 ppm) but also the addition of CuO-NPs can significantly boost the wettability alteration toward strongly water-wet condition (23.4° for the concentration of 1000 ppm of CuO-NPs). Finally, several core flooding experiments are performed using different combinations of chemicals to find the effect of these chemicals on the tertiary oil recovery factor. The results reveal that the presence of CuO-NPs can enhance the oil recovery of injected chemical slug (aqueous solution prepared by dissolution of IL with an oil recovery factor of 10.1% based on Original oil in place (OOIP)) to 13.8, %, 16.9%, and 21.2% based on OOIP if 500, 1000, 2000 ppm of CuO-NPs existed in the solution concomitant with 1000 ppm of [C12mim][Cl].