Thermal Comfort Evaluation with Fireplace in Occupied Space

2013 ◽  
Vol 649 ◽  
pp. 129-132 ◽  
Author(s):  
Radoslav Ponechal ◽  
Silvia Baďurová
Keyword(s):  
Thermal Comfort ◽  
Air Temperature ◽  
Infrared Camera ◽  
Heating System ◽  
Living Room ◽  
Air Velocity ◽  
Comfort Levels ◽  
Occupant Comfort ◽  
Thermal Climate ◽  
The Mean

The solid fuel heaters are popular in Slovakia again, where about 50% of new freestanding homes have one. The classic fireplace, with a blazing fire open to the room as traditional symbol of comfort and security becomes with better building thermal insulation a primary rather than an occasional indulgence heat source. This paper reports the results of field measurement and simulation investigating the thermal comfort criteria in occupied space with fireplace heating system. The field study was performed in a small furnished living-room. The indoor surface temperatures were captured with infrared camera and the mean radiant temperatures were calculated by the ESP-r simulation tool. Thermal comfort prediction maps (PPD and PMV index) are presented to describe range of occupant comfort levels with mean air temperature, air velocity and clothing level variations. It was found that this system provide full area improved thermal climate only with high air temperature level. The study was limited to the case with no vertical air temperature distribution.

scholarly journals Thermal comfort of patients in hospital ward areas

1977 ◽  
Vol 78 (1) ◽  
pp. 17-26 ◽  
Author(s):  
R. M. Smith ◽  
A. Rae
Keyword(s):  
Steady State ◽  
Thermal Comfort ◽  
Air Temperature ◽  
Hospital Ward ◽  
Patient Comfort ◽  
Mean Radiant Temperature ◽  
Air Velocity ◽  
Assessment Techniques ◽  
The Mean ◽  
Radiant Temperature

SUMMARYThe patient is identified as being of prime importance for comfort standards in hospital ward areas, other ward users being expected to adjust their dress to suit the conditions necessary for patient comfort. A study to identify the optimum steady state conditions for patient comfort is then described.Although this study raises some doubts as to the applicability of the standard thermal comfort assessment techniques to ward areas, it is felt that its results give a good indication of the steady-state conditions preferred by the patients. These were an air temperature of between 21.5° and 22° C and a relative humidity of between 30% and 70%, where the air velocity was less than 0.1 m/s and the mean radiant temperature was close to air temperature.

scholarly journals MEAN SURFACE TEMPERATURE OF JAPANESE QUAIL EXPOSED TO DIFFERENT LEVELS OF AIR VELOCITY AND TEMPERATURE AT START OF LAY

2020 ◽  
Vol 4 (2) ◽  
pp. 15-18
Author(s):  
Tatiany Carvalho dos Santos ◽  
Richard Stephen Gates ◽  
Ilda De Fátima Ferreira Tinôco ◽  
Sérgio Zolnier ◽  
Letícia Cibele da Silva Ramos Freitas
Keyword(s):  
Surface Temperature ◽  
Air Temperature ◽  
Japanese Quail ◽  
Systems Engineering ◽  
Air Velocity ◽  
Agricultural Engineering ◽  
Initial Stage ◽  
Different Temperatures ◽  
The Mean ◽  
Different Levels

The objective of this study was to evaluate the effect of different air velocities and temperature at the feeder on mean surface temperature of Japanese quail during the initial stage of laying. The experiment was carried out at the Center for Research in Environment and Agroindustry Systems Engineering (AMBIAGRO), Department of Agricultural Engineering, Federal University of Viçosa, Viçosa/MG, Brazil. A total of 216 Japanese quail in the initial laying phase were placed in four environmental chambers with different temperatures and air velocity, where they were housed and distributed randomly in 2 galvanized wire cages, with 3 partitions each and 27 birds/cage, and a density of approximately 155.6 cm²/bird. The experimental design consisted of randomized blocks with replications of two treatments (air velocity at the feeder: 0, 1, 2, and 3 m/s and air temperature: 17, 23, 29 and 35°C). The mean surface temperature was analyzed by Two-Way ANOVA, with treatment means separated by the Tukey test (P < 0.05). There was a significant positive correlation between air temperature and mean surface temperature (MST). Air velocity is important in removing heat from the surface of birds.

scholarly journals Control, Regulation and Command System of Hydronic Radiant Floors Heating by Wireless and Energy Harvesting Sensors and Actuators

2013 ◽  
Vol 543 ◽  
pp. 389-392 ◽  
Author(s):  
Gilberto Batista ◽  
Pedro Dinis Gaspar ◽  
Pedro D. Silva
Keyword(s):  
Energy Harvesting ◽  
Thermal Comfort ◽  
Air Temperature ◽  
Heating System ◽  
Comfort Level ◽  
Sensors And Actuators ◽  
Control Regulation ◽  
Radiant Temperature ◽  
And Control ◽  
Actual Control

This paper presents the development of an innovative control, regulation and command system for hydronic radiant floors, more flexible and efficient that guarantees a better thermal comfort to the user and simultaneously improves the energy efficiency of this type of heating system. The majority of the actual control of hydronic radiant floors is done by thermostats that measure the air temperature and control the actuators (pumps and valves) in order to maintain the room at the specified temperature. These systems requires the frequent adjustment of thermostats set-point in order to obtain thermal comfort as it depends on other factors than just the air temperature, such as, the air humidity, external environmental conditions, radiant temperature, among others. This paper presents a control, regulation and command solution that requires minimum user intervention, as the user only has to choose the desirable thermal comfort level. The control algorithm is based on the calculation of PMV (Predicted Mean Vote) index as defined on Thermal Comfort Standard ISO 7730. Another advantage of the proposed system is related to the wireless and energy harvesting sensors and actuators that provide much more flexibility to the system.

scholarly journals Thermal Comfort in Living Room of Houses with Different Frontage

2021 ◽  
Vol 6 (16) ◽  
pp. 249-259
Author(s):  
Ahmad Ridzwan Othman ◽  
Mohammad Ezzat Fakhrawi Mohammad Faisal ◽  
Wahyuni Zahrah
Keyword(s):  
Thermal Comfort ◽  
Publishing House ◽  
Sun Exposure ◽  
Living Room ◽  
Data Logger ◽  
Comfort Levels ◽  
International Publishing ◽  
Shading Devices ◽  
House Design ◽  
Open Access Article

House frontage is an essential aspect of terraced house design to ensure the occupant's comfort and healthy living. Four samples selected to evaluate the influence of the window to wall ratio (WWR) towards the internal thermal comfort of the house. The indoor thermal parameters were recorded using HOBOware Data Logger and evaluated using CBE Thermal Comfort Calculator. The study shows that the living room with a bigger WWR had the lowest thermal comfort levels. Besides the WWR, window placements and the shading devices also help in reducing the sun exposure of the frontage wall and increase the indoor thermal comfort. Keywords: Frontage; Thermal Comfort; Window to Wall Ratio; Sun Exposure eISSN: 2398-4287© 2021. The Authors. Published for AMER ABRA cE-Bs by e-International Publishing House, Ltd., UK. This is an open access article under the CC BYNC-ND license (http://creativecommons.org/licenses/by-nc-nd/4.0/). Peer–review under responsibility of AMER (Association of Malaysian Environment-Behaviour Researchers), ABRA (Association of Behavioural Researchers on Asians/Africans/Arabians) and cE-Bs (Centre for Environment-Behaviour Studies), Faculty of Architecture, Planning & Surveying, Universiti Teknologi MARA, Malaysia. DOI: https://doi.org/10.21834/ebpj.v6i16.2636

scholarly journals PENGARUH BUKAAN SAMPING (CLERESTORY) TERHADAP KUALITAS KENYAMANAN TERMAL PADA FOOD CARNIVAL, MALL AEON BSD

Vitruvian ◽  
2019 ◽  
Vol 9 (1) ◽  
pp. 47
Author(s):  
Tathia Edra Swasti
Keyword(s):  
Wind Speed ◽  
Thermal Comfort ◽  
Air Temperature ◽  
Effective Temperature ◽  
Air Humidity ◽  
Air Velocity ◽  
Predicted Mean Vote ◽  
Air Speed ◽  
The Right

ABSTRAK Mall saat ini marak menggunakan clerestory sebagai salah satu upaya untuk penerangan alami pada siang hari. Namun, cahaya matahari pada sore hari (barat) akan menghasilkan cahaya matahari yang lebih panas dan silau dibandingkan cahaya matahari pada pagi hari (timur). Oleh karena itu, dengan pemakaian clerestory yang cukup besar pada bangunan, masalah panas tentu tak dapat dihindari. Begitu pula dengan glare yang berasal dari pantulan sinar matahari. Salah satu Mall yang menggunakan clerestory adalah Mall AEON BSD. Pengukuran suhu udara, temperatur efektif, kelembaban udara, kecepatan angin, PMV (Predicted Mean Vote) dan PPD (Predicted Percentage of Dissatisfied) dilaksanakan pada 4 waktu dengan 5 lokasi titik ukur yang memiliki kondisi berbeda untuk membuktikan bahwa clerestory dapat mempengaruhi kenyamanan termal. Disimpulkan bahwa titik 2 yaitu titik yang berdekatan dengan clerestory sisi kanan (ukurannya lebih kecil daripada clerestory sisi kiri) memiliki temperatur efektif dan kelembaban udara yang lebih rendah dari titik lain, dan kecepatan udara (dipengaruhi oleh hembusan AC) lebih tinggi dari titik lain. Responden merasa nyaman saat berada di titik tersebut.Titik paling nyaman menurut responden adalah titik 2 dengan TE rata-rata berkisar 27,4˚C, kelembaban udara rata-rata berkisar 52,2%, kecepatan udara rata-rata berkisar 0,15 m/s, PMV berkisar 0,5 dan PPD berkisar 12,7%. Dengan begitu semakin kecil ukuran skylight terbukti mempengaruhi kenyamanan termal dan membuat kenyamanan termal dapat tercapai. Kata Kunci: Mall, Clerestory, PMV, PPD, Kenyamanan Termal ABSTRACT Nowadays mall is decorated with clerestory as an effort to lighten naturally during the day. However, sunlight in the afternoon (west) will produce more sunlight and glare than sunlight in the morning (east). Therefore, with the use of a fairly large clerestory in buildings, the problem of heat certainly can not be avoided. Similarly, glare that comes from the reflection of sunlight. One of the malls that use clerestory is BSD AEON Mall. Measurement of air temperature, effective temperature, air humidity, wind speed, PMV (Predicted Mean Vote) and PPD (Predicted Percentage of Dissatisfied) carried out at 4 times within 5 measuring spots that have different conditions, proving that clerestory can affect thermal comfort. It was concluded that point 2, which is the point adjacent to the right side clerestory (smaller in size than the left side clerestory) has an effective temperature and lower air humidity than other points, and air velocity (affected by blowing AC) is higher than other points. Respondents felt comfortable when they were at that point. The most comfortable point according to respondents was point 2 with TE averaging around 27.4˚C, air humidity averaged 52.2%, the average air speed ranged from 0.15 m / s, PMV ranges from 0.5 and PPD ranges from 12.7%. Thus, the smaller size of the clerestory is affecting thermal comfort and thermal comfort can be achieved. Keywords: Mall, Clerestory, PMV, PPD, Thermal Comfort

scholarly journals Experimental verification of a CFD model for the closed plant factory under artificial lighting

2020 ◽  
Vol 213 ◽  
pp. 03013
Author(s):  
Wei Lu ◽  
Yiwen Hu ◽  
Shenghan Zhou ◽  
Xin Zhang ◽  
Quan Yuan ◽  
...  
Keyword(s):  
Fluid Dynamics ◽  
Air Temperature ◽  
Experimental Verification ◽  
Cfd Model ◽  
Air Velocity ◽  
Artificial Lighting ◽  
Mean Relative Error ◽  
Plant Factory ◽  
Computational Fluid Dynamics Cfd ◽  
The Mean

A computational fluid dynamics (CFD) model for the closed plant factory under artificial lighting has been developed in this study, the experimental verification of CFD model with the air velocity value was compared with the measured air temperature value. The results showed that the mean relative error of validation with the air velocity was 15%, and comparable with experimentally observed air temperature profile inside the plant factory with RMSE of 3% which show the utility of CFD to study plant factory microclimatic parameters.

On the Development of a Thermal Comfort Control for Classrooms Conditioned by Split-Type Systems

2019 ◽  
Author(s):  
Anastacio Silva Junior ◽  
Nathan Mendes ◽  
Rogério Vilain ◽  
Marcelo Pereira ◽  
Katia Cordeiro Mendonça
Keyword(s):  
Thermal Comfort ◽  
Air Temperature ◽  
Low Cost ◽  
Type System ◽  
Type Systems ◽  
General Purpose ◽  
Representative Point ◽  
Air Velocity ◽  
Comfort Index ◽  
Air Speed

Abstract Thermal comfort conditions may vary substantially within an air-conditioned room equipped by split-type systems. In this work, the comfort conditions in a classroom were evaluated experimentally based on the PMV index, according to ISO 7730 Standard that defines the thermal satisfaction in occupied environments. The experiment was carried out at three different supply airflows (high, medium and low) and three set-point temperatures (23, 24 and 25°C). The results showed that there is a considerable variation in the air velocity field in the room as well as in the PMV values for three different supply airflows, consequently significant changes of thermal comfort indices can be noticed. Several curves were adjusted aiming to express the values of PMV, deriving a simplified comfort index for rooms conditioned by split-type systems based on dry-bulb air temperature and air speed. The purpose of this adjustment is to obtain an equation that provides the value of the comfort index for cooling purposes. Thus, for a certain condition of use, one can predict what will be the value of PMV in an occupied environment, enabling the implementation of a control system of the comfort according to this new index (ICS). The variables considered in obtaining the curve were the air temperature (Tar) and the air velocity (Var), since these two variables can be controlled directly by the split-type system. The general purpose of this work is to provide experimental data for the development of a low-cost device to automatically control ICS-based thermal comfort in a space conditioned by a split-type system through a single and representative point within the classroom.

CFD-Based Parametric Analysis on the Performance of Personalized Partition Air Distribution Systems

Solar Energy ◽  
2006 ◽  
Author(s):  
Kybum Jeong ◽  
Moncef Krarti ◽  
Zhiqiang Zhai
Keyword(s):  
Thermal Comfort ◽  
Air Temperature ◽  
Distribution System ◽  
Distribution Systems ◽  
Comfort Level ◽  
Cfd Modeling ◽  
Air Distribution ◽  
Air Velocity ◽  
Comfort Index ◽  
System Mode

The partition air distribution systems evaluated in this study allow occupants to control the system mode (on/off) and the supply air velocity and direction with similar flexibility as occupants in automobiles. To find optimal specifications for the partition air distribution systems that are able to achieve comfortable micro-environment, a CFD modeling tool was used to simulate the airflow and thermal performance of the partition air distribution systems in a typical office space. By analyzing the distribution characteristics of indoor air temperature, air velocity and thermal comfort index, the study assessed the performance of the partition air distribution systems with different operating parameters. The simulation results were analyzed and evaluated to assess both occupant’s thermal comfort and system energy consumption. The study shows that space cooling energy can be reduced while maintaining acceptable indoor thermal comfort level using a partition air distribution system with a higher supply air temperature.

Analysis of Natural Ventilation Systems in Schoolrooms

2016 ◽  
Vol 824 ◽  
pp. 625-632
Author(s):  
Mária Budiaková
Keyword(s):  
Mechanical Ventilation ◽  
Thermal Comfort ◽  
Energy Saving ◽  
Air Temperature ◽  
Natural Ventilation ◽  
Winter Period ◽  
Experimental Measurements ◽  
Air Velocity ◽  
The Future ◽  
Ventilation Systems

The paper is oriented on the analysis of the ventilation systems in schoolrooms. Correct and sufficient ventilation of schoolrooms is very important because students and pupils spend in the schoolrooms the majority of their time in school. In our schools the ventilation is incorrect and insufficient. The biggest problem is winter period when the ventilation is provided only by opening the doors to corridor. This way, there is insufficient intake of oxygen, which causes distractibility and feeling of tiredness of pupils. In current schoolrooms we can use only natural ventilation and thus the schoolrooms have to be ventilated using windows. Therefore this research was focused on the comparison and the analysis of different systems of natural ventilation in schoolrooms. The experimental measurements were carried out in schoolroom, where the parameters of thermal comfort were measured in the different systems of natural ventilation with device Testo 480 which was connected to computer. Gained values of air temperature, air velocity and index PMV are presented in graphs. On the base of analysis of measured values were evaluated the systems of natural ventilation for schoolrooms. In the future, the mechanical ventilation in schoolrooms can be assumed, therefore the recommendation on modern energy saving system of mechanical ventilation is in the end of this paper.

scholarly journals Thermal comfort and draught assessment in a modern open office building in Tallinn

2019 ◽  
Vol 111 ◽  
pp. 02013 ◽  
Author(s):  
Martin Kiil ◽  
Alo Mikola ◽  
Martin Thalfeldt ◽  
Jarek Kurnitski
Keyword(s):  
Thermal Comfort ◽  
Air Temperature ◽  
Energy Demand ◽  
Working Environment ◽  
Office Building ◽  
Indoor Climate ◽  
Air Velocity ◽  
Air Exchange Rate ◽  
Air Speed ◽  
Open Office

Modern office building users have high expectations about the working environment and thermal comfort, which requires the installation of complex technical systems such as combined cooling and ventilation. Room conditioning units of these systems must ensure temperature and ventilation control in a way that air velocity is low and the air temperature in acceptable range. Achieving air distribution avoiding draught is one of the key elements of a thermal comfort in modern office landscape. Higher air velocity in occupied zone is easily perceived as draught, which causes occupant dissatisfaction and complaints, as well as decrease in the productivity or effective floor space area. To reduce complaints, room air temperature setpoints or ventilation airflow rates are often modified, which may result in higher heating energy demand. In addition, excessive heating setpoint rise will not only consume more energy, but may cause health problems. Compared to cellular offices it is more difficult to ensure thermal comfort conditions in open office spaces where there are no walls for air flows. In addition, due to the higher number of employees it is more difficult to meet satisfactory conditions for everyone. The aim of this study was to evaluate thermal comfort parameters such as room air temperature, air speed and supply air temperature and how the users sense it in a modern office building in Tallinn, Estonia. Design room air temperature setpoints and air exchange rate were evaluated on open office spaces. Measured data with web-based indoor climate questionnaire was analysed. Results show which design and measured parameters make it possible to match the user comfort at all times.

Sign in / Sign up

Export Citation Format

Share Document