Feasibility Study on Development of Heavy Oil Reservoir by Steam-Nitrogen Assisted Gravity Drainage

2013 ◽  
Vol 827 ◽  
pp. 224-231 ◽  
Author(s):  
Han Sheng Mu ◽  
Yi Ning Ning Wang ◽  
Zhuang Zhang ◽  
Zhong Ya Zhou ◽  
Ying Xue Liu
Keyword(s):  
Heavy Oil ◽  
Oil Industry ◽  
Steam Injection ◽  
Gravity Drainage ◽  
Gas Oil ◽  
Theory Analysis ◽  
Steam Assisted Gravity Drainage ◽  
Engineering Theory ◽  
Cumulative Production ◽  
Very High

Currently, the primary method for developing extra heavy oil is the steam assisted gravity drainage (SAGD) characterized by high recovery factor and gas-oil ratio. However, in the course of application of this technology, because the whole reservoir needs to be heated to a very high temperature, too much steam is needed, and simultaneously, the loss of heat of reservoir is also increased. For the purpose of exploiting the extra heavy oil more economically, a SAGP technique, the steam and gas push, is put forward in the oil industry world. This paper takes the adding of nitrogen as an example, conducts reservoir engineering theory analysis, numerical simulation study and physical modeling study, and concludes that when adopting SAGP technique, it is unnecessary to increase the temperature of the whole reservoir to a very high value; compared with SAGD, although the cumulative production of SAGP declines to some extent, the steam injection volume is only 68% of that of SAGD, which indicates that SAGP exploitation technique can save steam and thus reduce the production cost compared with SAGD.

Optimisation of Steam Assisted Gravity Drainage [SAGD] for Improved Recovery from Unconsolidated Heavy Oil Reservoirs

2011 ◽  
Vol 367 ◽  
pp. 403-412 ◽  
Author(s):  
Babs Mufutau Oyeneyin ◽  
Amol Bali ◽  
Ebenezer Adom
Keyword(s):  
Oil Recovery ◽  
Heavy Oil ◽  
Oil Industry ◽  
Steam Injection ◽  
Thermal Capacity ◽  
Thermal Recovery ◽  
Viscosity Reduction ◽  
Gravity Drainage ◽  
Steam Assisted Gravity Drainage ◽  
The Impact

Most of the heavy oil resources in the world are in sandstone reservoir rocks, the majority of which are unconsolidated sands which presents unique challenges for effective sand management. Because they are viscous and have less mobility, then appropriate recovery mechanisms that lower the viscosity to the point where it can readily flow into the wellbore and to the surface are required. There are many cold and thermal recovery methods assisted by gravity drainage being employed by the oil industry. These are customised for specific reservoir characteristics with associated sand production and management problems. Steam Assisted Gravity Drainage (SAGD) based on horizontal wells and gravity drainage, is becoming very popular in the heavy oil industry as a thermal viscosity reduction technique. SAGD has the potential to generate a heavy oil recovery factor of up to 65% but there are challenges to ‘’realising the limit’’. The process requires elaborate planning and is influenced by a combination of factors. This paper presents unique models being developed to address the issue of multiphase steam-condensed water-heavy oil modelling. It addresses the effects of transient issues such as the changing pore size distribution due to compaction on the bulk and shear viscosities of the non-Newtonian heavy oil and the impact on the reservoir productivity, thermal capacity of the heavy oil, toe-to-heel steam injection rate and quality for horizontal well applications. Specific case studies are presented to illustrate how the models can be used for detailed risk assessment for SAGD design and real-time process optimisation necessary to maximise production at minimum drawdown. Nomenclature

Mathematical Modeling of Steam Assisted Gravity Drainage

2005 ◽  
Vol 8 (05) ◽  
pp. 372-376 ◽  
Author(s):  
Serhat Akin
Keyword(s):  
Mathematical Model ◽  
Heavy Oil ◽  
Steam Injection ◽  
Viscosity Reduction ◽  
Gravity Drainage ◽  
Heavy Oils ◽  
Production Well ◽  
Steam Chamber ◽  
Steam Assisted Gravity Drainage ◽  
Wide Range

Summary A mathematical model for gravity drainage in heavy-oil reservoirs and tar sands during steam injection in linear geometry is proposed. The mathematical model is based on the experimental observations that the steam-zone shape is an inverted triangle with the vertex fixed at the bottom production well. Both temperature and asphaltene content dependence on the viscosity of the drained heavy oil are considered. The developed model has been validated with experimental data presented in the literature. The heavy-oil production rate conforms well to previously published data covering a wide range of heavy oils and sands for gravity drainage. Introduction Gravity drainage of heavy oils is of considerable interest to the oil industry. Because heavy oils are very viscous and, thus, almost immobile, a recovery mechanism is required that lowers the viscosity of the material to the point at which it can flow easily to a production well. Conventional thermal processes, such as cyclic steam injection and steam-assisted gravity drainage(SAGD), are based on thermal viscosity reduction. Cyclic steam injection incorporates a drive enhancement from thermal expansion. On the other hand, SAGD is based on horizontal wells and maximizing the use of gravity forces. In the ideal SAGD process, a growing steam chamber forms around the horizontal injector, and steam flows continuously to the perimeter of the chamber, where it condenses and heats the surrounding oil. Effective initial heating of the cold oil is important for the formation of the steam chamber in gravity-drainage processes. Heat is transferred by conduction, by convection, and by the latent heat of steam. The heated oil drains to a horizontal production well located at the base of the reservoir just below the injection well. Based on the aforementioned concepts, Butler et al. derived Eq. 1 assuming that the steam pressure is constant in the steam chamber, that only steam flows in the steam chamber, that oil saturation is residual, and that heat transfer ahead of the steam chamber to cold oil is only by conduction. One physical analogy of this process is that of a reservoir in which an electric heating element is placed horizontally above a parallel horizontal producing well.

Investigation of Emulsion Flow in Steam-Assisted Gravity Drainage

SPE Journal ◽  
2013 ◽  
Vol 18 (03) ◽  
pp. 440-447 ◽  
Author(s):  
C.C.. C. Ezeuko ◽  
J.. Wang ◽  
I.D.. D. Gates
Keyword(s):  
Experimental Data ◽  
Numerical Simulation ◽  
Oil Recovery ◽  
Vital Role ◽  
Gravity Drainage ◽  
Steam Assisted Gravity Drainage ◽  
Emulsion Flow ◽  
Very High ◽  
Effective Representation

Summary We present a numerical simulation approach that allows incorporation of emulsion modeling into steam-assisted gravity-drainage (SAGD) simulations with commercial reservoir simulators by means of a two-stage pseudochemical reaction. Numerical simulation results show excellent agreement with experimental data for low-pressure SAGD, accounting for approximately 24% deficiency in simulated oil recovery, compared with experimental data. Incorporating viscosity alteration, multiphase effect, and enthalpy of emulsification appears sufficient for effective representation of in-situ emulsion physics during SAGD in very-high-permeability systems. We observed that multiphase effects appear to dominate the viscosity effect of emulsion flow under SAGD conditions of heavy-oil (bitumen) recovery. Results also show that in-situ emulsification may play a vital role within the reservoir during SAGD, increasing bitumen mobility and thereby decreasing cumulative steam/oil ratio (cSOR). Results from this work extend understanding of SAGD by examining its performance in the presence of in-situ emulsification and associated flow of emulsion with bitumen in porous media.

Numerical Simulation of Thermal Solvent Replacing Steam under Steam Assisted Gravity Drainage SAGD Process

2010 ◽  
Author(s):  
Weiqiang Li ◽  
Daulat D. Mamora
Keyword(s):  
High Temperature ◽  
Oil Recovery ◽  
Oil Sands ◽  
Steam Injection ◽  
Thermal Recovery ◽  
Production Performance ◽  
Gravity Drainage ◽  
Steam Assisted Gravity Drainage ◽  
Recovery Technique ◽  
Simulation Results

Abstract Steam Assisted Gravity Drainage (SAGD) is one successful thermal recovery technique applied in the Athabasca oil sands in Canada to produce the very viscous bitumen. Water for SAGD is limited in supply and expensive to treat and to generate steam. Consequently, we conducted a study into injecting high-temperature solvent instead of steam to recover Athabasca oil. In this study, hexane (C6) coinjection at condensing condition is simulated using CMG STARS to analyze the drainage mechanism inside the vapor-solvent chamber. The production performance is compared with an equivalent steam injection case based on the same Athabasca reservoir condition. Simulation results show that C6 is vaporized and transported into the vapor-solvent chamber. At the condensing condition, high temperature C6 reduces the viscosity of the bitumen more efficiently than steam and can displace out all the original oil. The oil production rate with C6 injection is about 1.5 to 2 times that of steam injection with oil recovery factor of about 100% oil initially-in-place. Most of the injected C6 can be recycled from the reservoir and from the produced oil, thus significantly reduce the solvent cost. Results of our study indicate that high-temperature solvent injection appears feasible although further technical and economic evaluation of the process is required.

scholarly journals A steam rising model of steam-assisted gravity drainage production for heavy oil reservoirs

2019 ◽  
Vol 38 (4) ◽  
pp. 801-818
Author(s):  
Ren-Shi Nie ◽  
Yi-Min Wang ◽  
Yi-Li Kang ◽  
Yong-Lu Jia
Keyword(s):  
Production Rate ◽  
Horizontal Well ◽  
Oil Production ◽  
Steam Injection ◽  
Injection Rate ◽  
Gravity Drainage ◽  
Model Parameters ◽  
Steam Quality ◽  
Steam Chamber ◽  
Steam Assisted Gravity Drainage

The steam chamber rising process is an essential feature of steam-assisted gravity drainage. The development of a steam chamber and its production capabilities have been the focus of various studies. In this paper, a new analytical model is proposed that mimics the steam chamber development and predicts the oil production rate during the steam chamber rising stage. The steam chamber was assumed to have a circular geometry relative to a plane. The model includes determining the relation between the steam chamber development and the production capability. The daily oil production, steam oil ratio, and rising height of the steam chamber curves influenced by different model parameters were drawn. In addition, the curve sensitivities to different model parameters were thoroughly considered. The findings are as follows: The daily oil production increases with the steam injection rate, the steam quality, and the degree of utilization of a horizontal well. In addition, the steam oil ratio decreases with the steam quality and the degree of utilization of a horizontal well. Finally, the rising height of the steam chamber increases with the steam injection rate and steam quality, but decreases with the horizontal well length. The steam chamber rising rate, the location of the steam chamber interface, the rising time, and the daily oil production at a certain steam injection rate were also predicted. An example application showed that the proposed model is able to predict the oil production rate and describe the steam chamber development during the steam chamber rising stage.

Feasibility of time-lapse gravity and gravity gradiometry monitoring for steam-assisted gravity drainage reservoirs

Geophysics ◽  
2015 ◽  
Vol 80 (2) ◽  
pp. WA99-WA111 ◽  
Author(s):  
Anya Reitz ◽  
Richard Krahenbuhl ◽  
Yaoguo Li
Keyword(s):  
Heavy Oil ◽  
Production Efficiency ◽  
Low Cost ◽  
Time Lapse ◽  
Gravity Drainage ◽  
Great Success ◽  
Gravity Gradiometry ◽  
Steam Chamber ◽  
Steam Assisted Gravity Drainage ◽  
The Cost

There is presently an increased need to monitor production efficiency as heavy oil reservoirs become more economically viable. We present a feasibility study of monitoring steam-assisted gravity drainage (SAGD) reservoirs using time-lapse gravimetry and gravity gradiometry. Even though time-lapse seismic has historically shown great success for SAGD monitoring, the gravimetry and gravity gradiometry methods offer a low-cost interseismic alternative that can complement the seismic method, increase the survey frequency, and decrease the cost of monitoring. In addition, both gravity-based methods are directly sensitive to the density changes that occur as a result of the replacement of heavy oil by steam. Advances in technologies have made both methods viable candidates for consideration in time-lapse reservoir monitoring, and we have numerically evaluated their potential application in monitoring SAGD production. The results indicate that SAGD production should produce a strong anomaly for both methods at typical SAGD reservoir depths. However, the level of detail for steam-chamber geometries and separations that can be recovered from the gravimetry and gravity gradiometry data is site dependent. Gravity gradiometry shows improved monitoring ability, such as better recovery of nonuniform steam movement due to reservoir heterogeneity, at shallower production reservoirs. Gravimetry has the ability to detect SAGD steam-chamber growth to greater depths than does gravity gradiometry, although with decreasing resolution of the expanding steam chambers.

Sign in / Sign up

Export Citation Format

Share Document