Effect of Equal Channel Angular Pressing on Microstructure and Recrystallization Temperature of Al-Cu Alloy

2014 ◽  
Vol 875-877 ◽  
pp. 1581-1584
Author(s):  
Da Ran Fang ◽  
Chun Liu ◽  
Feng Fang Liu ◽  
Li Wei Quan ◽  
Jia Jun Li ◽  
...  
Keyword(s):  
Cold Rolling ◽  
Equal Channel Angular Pressing ◽  
Rolling Reduction ◽  
Recrystallization Temperature ◽  
Angular Pressing ◽  
Cu Alloy ◽  
Cold Rolling Reduction ◽  
Different Temperatures

Al-0.6%Cu alloy processed by equal channel angular pressing (ECAP) was investigated in this study. The samples processed with 1, 2 and 4 ECAP passes were annealed at different temperatures. And the microstructures of the Al-0.63%Cu alloy samples were observed. The results show that the grains of the alloy are refined to sub-micron level after multipass ECAP. Moreover, it is found that the recrystallization temperature of the Al-0.6%Cu alloy samples decreases with increasing the number of ECAP passes. Based on the study above, effect of cold rolling reduction and ECAP passes on recrystallization temperature of materials should be further investigated.

scholarly journals Twinning Behavior in Cold-Rolling Ultra-Thin Grain-Oriented Silicon Steel

Crystals ◽  
2021 ◽  
Vol 11 (2) ◽  
pp. 187
Author(s):  
Bo Zhang ◽  
Li Meng ◽  
Guang Ma ◽  
Ning Zhang ◽  
Guobao Li ◽  
...  
Keyword(s):  
Cold Rolling ◽  
Rolling Process ◽  
Silicon Steel ◽  
Mechanical Work ◽  
Area Fraction ◽  
Raw Material ◽  
Rolling Reduction ◽  
Cold Rolling Reduction ◽  
Schmid Factor ◽  
Twinning System

Twinning behaviors in grains during cold rolling have been systematically studied in preparing ultra-thin grain-oriented silicon steel (UTGO) using a commercial glassless grain-oriented silicon steel as raw material. It is found that the twinning system with the maximum Schmid factor and shear mechanical work would be activated. The area fraction of twins increased with the cold rolling reduction. The orientations of twins mainly appeared to be α-fiber (<110>//RD), most of which were {001}<110> orientation. Analysis via combining deformation orientation simulation and twinning orientation calculation suggested that {001}<110> oriented twinning occurred at 40–50% rolling reduction. The simulation also confirmed more {100} <011> oriented twins would be produced in the cold rolling process and their orientation also showed less deviation from ideal {001}<110> orientation when a raw material with a higher content of exact Goss oriented grains was used.

Effect of Equal Channel Angular Pressing and Annealing on Corrosion Resistance of Al-Cu Alloy

2013 ◽  
Vol 803 ◽  
pp. 226-229
Author(s):  
Da Ran Fang ◽  
Chun Liu ◽  
Feng Fang Liu
Keyword(s):  
Corrosion Resistance ◽  
Low Temperature ◽  
Equal Channel Angular Pressing ◽  
Annealing Treatment ◽  
Coarse Grained ◽  
Nacl Solution ◽  
Angular Pressing ◽  
Cu Alloy ◽  
Low Temperature Annealing ◽  
Ultrafine Grained

Al-3.9wt.%Cu alloy was subjected to equal channel angular pressing (ECAP) and subsequent low temperature annealing treatment, and the corrosion resistance of the samples was investigated by potentiodynamic polarization measurements in 3.5% NaCl solution. The results show that the corrosion rate of the ultrafine-grained alloy increases, in comparison with the coarse-grained alloy. Meanwhile, it is noted that the corrosion resistance of the alloy subjected to ECAP can be improved by relief annealing.

Thermal Stability of Mechanical Properties of Copper after Equal-Channel Angular Pressing

2008 ◽  
Vol 584-586 ◽  
pp. 960-965 ◽  
Author(s):  
Tamara Kravchenko ◽  
Alexander Korshunov ◽  
Natalia Zhdanova ◽  
Lev Polyakov ◽  
Irina Kaganova
Keyword(s):  
Mechanical Properties ◽  
Thermal Stability ◽  
Tensile Strength ◽  
Chemical Composition ◽  
Yield Strength ◽  
Equal Channel Angular Pressing ◽  
Angular Pressing ◽  
Different Temperatures ◽  
Thermal Stability Of

Annealed oxygen-free and tough-pitch copper samples have been processed by equalchannel angular pressing (ECAP) by route BC. The samples included 8 x 8 mm section pieces and a 40 mm diameter bar. Thermal stability was assessed based on the changes in the standard mechanical properties (conventional yield strength, tensile strength, elongation, proportional elongation and contraction) after annealing at different temperatures for 1 hour. Thermal stability of the same grade of material has been found to be different for different batches and to depend on the structural conditions of deformed material. The zone of thermal stability for copper of the two grades of interest does not depend on the material’s chemical composition.

scholarly journals Effects of Cold Rolling Reduction on Secondary Recrystallization of Fe-3%Si Alloy

2002 ◽  
Vol 88 (3) ◽  
pp. 155-162
Author(s):  
Takahide SHIMAZU ◽  
Satoshi ARAI ◽  
Tomohiko SAKAI ◽  
Harushige TSUBAKINO
Keyword(s):  
Cold Rolling ◽  
Secondary Recrystallization ◽  
Rolling Reduction ◽  
Cold Rolling Reduction
Sign in / Sign up

Export Citation Format

Share Document