Long-Term Corrosion Resistance of Biomedical Grade Stainless Steel ISO 5832-1 ("316LVM") under External Anodic Electrical Pulsing Conditions

2010 ◽  
Vol 89-91 ◽  
pp. 455-460
Author(s):  
Ronald Rebentisch ◽  
Regina Lange ◽  
Ulrich Beck

For medical implant application of metals or alloys, one major prerequisite is the absence of release of metal ions to the surrounding tissue. In the case of stainless steel, this prerequisite can be achieved by modifying the surface by chemical and electrochemical passivation pre-treatments so that the general corrosion-rate will be reduced and pitting corrosion will not occur. In a first step, the surface of the test specimens (10 mm diam.) were chemically pre-treated with nitric acid using different concentrations and duration. In the second step, the passivation effect was tested by applying voltage-scans reaching from hydrogen to oxygen evolution in a 3-electrode CV-measurement using phosphate buffered saline (PBS) (pH7.4) as electrolyte. It turned out that after the 2nd of a total of five scans all CV-diagrams looked almost the same and the chemical passiva-tion treatment was of minor effect; none of the CV-diagrams showed effects of pitting corrosion. The third step was to apply external electrical anodic pulses (n=5.3x106) on the surface of the specimen (+4.5V, 0.5ms, 740Hz). In the forth step, the passive behaviour again was tested using the same CV-measurement setup. Again, no effect of pitting corrosion was seen and in parts of the CV-diagrams the measured current signal was less than before.

2022 ◽  
Vol 7 (1) ◽  
pp. 77-83
Author(s):  
Andrea Szabó Nagy ◽  
Kálmán Varga ◽  
Bernadett Baja ◽  
Zoltán Németh ◽  
Desző Oravetz ◽  
...  

Our previous studies have revealed that a ”hybrid” structure of the amorphous and crystalline phases is formed in the outermost surface region of the austenitic stainless steel tubes of steam generators (SGs) as an undesired consequence of the industrial application of the AP-CITROX (AP: alkaline permanganate; CITROX: citric and oxalic acid) decontamination technology. The formation of this mobile oxide-layer increased the amount of the corrosion products in the primary circuit significantly, resulting in magnetite deposition on fuel assemblies. Owing to the fact that there is no investigation method available for the in-situ monitoring of the inner surfaces of heat exchanger tubes, a research project based on sampling as well as on ex-situ electrochemical and surface analytical measurements was elaborated. Within the frame of this project, comprehensive investigation of the general corrosion state and metallographic features of 36 stainless steel specimens, cut out from various locations of the 21 steam generators of the Paks NPP in the time period of 2000-2007 has been performed. The present work gives a brief overview on the general corrosion state of the heat exchanger tubes of SGs, concerning the long-term effects of the AP-CITROX procedure on the chemical composition and structure of the protective oxide-layer.


2020 ◽  
Vol ahead-of-print (ahead-of-print) ◽  
Author(s):  
Guanghui Yi ◽  
Dajiang Zheng ◽  
Guang-Ling Song

Purpose The purpose of this paper is to address the concern of some stainless steel users. To understand the effect of surface white spots on corrosion performance of stainless steel. Design/methodology/approach White spots appeared on some component surfaces made of 316 L stainless steel in some industrial applications. To address the concern about the pitting performance in the spot areas, the pitting corrosion potential and corrosion resistance were measured in the spot and non-spot areas by means of potentiodynamic polarization and electrochemical impedance spectroscopy and the two different surface characteristics were analytically compared by using optical microscopy, laser confocal microscopy, scanning electron microscopy, x-ray diffraction, energy dispersive spectroscopy and auger energy spectroscopy. The results indicated that the pitting performance of the 316 L stainless steel was not negatively influenced by the spots and the white spots simply resulted from the slightly different surface morphology in the spot areas. Findings The white spots are actually the slightly rougher surface areas with some carbon-containing species. They do not reduce the pitting resistance. Interestingly, the white spot areas even have slightly improved general corrosion resistance. Research limitations/implications Not all surface contamination or roughening can adversely affect the corrosion resistance of stainless steel. Practical implications Stainless steel components with such surface white spots are still qualified products in terms of corrosion performance. Originality/value The surface spot of stainless steel was systematically investigated for the first time for its effect on corrosion resistance and the conclusion was new to the common knowledge.


Metals ◽  
2020 ◽  
Vol 10 (6) ◽  
pp. 794 ◽  
Author(s):  
Yiqi Zhou ◽  
Dirk Lars Engelberg

Bipolar electrochemistry has been applied to Type 420 ferritic stainless steel in order to determine the full spectrum of anodic-to-cathodic polarisation behaviour. The occurrence of crevice corrosion, pitting corrosion in combination with general corrosion, pitting corrosion only, general corrosion only, followed by a cathodic region has been observed. Instances of pitting corrosion initiated near chromium-rich carbides with Cr23C6, Cr3C2, and Cr7C3 identified as pit nucleation sites. The observed pit growth kinetics were independent of the electrochemical over-potential. Characterisation of the pit size distributions supports the presence of a critical dissolved volume for the transition of metastable to stable pit growth and pit coalescence.


2008 ◽  
Vol 569 ◽  
pp. 197-200 ◽  
Author(s):  
Wei Zhang ◽  
De Ning Zou ◽  
Hong Hong Yao ◽  
Jun Yang

Copper is a well-known alloying element which is used to improve the resistance to general corrosion of stainless steels. Our previous experiments show that the increase of copper content can acquire the excellent antibacterial properties and can also increase the tendency to cold formability of the ferritic stainless steels. However, the effect of alloying Cu on the resistance to localized corrosion has not been clarified sufficiently. In order to understand the effect of copper on pitting corrosion resistance of the ferritic antibacterial stainless steel, the electrochemical experiments were carried out and the anodic polarization curves were performed in 3.5% NaCl solution for two kinds of steels. The results reveal that the ε-Cu phase in ferrite matrix diminishes pitting corrosion resistance of the antibacterial stainless steel in the chlorides medium. It is connected with the poor passive behavior of the ε-Cu phase inclusions.


2019 ◽  
Vol 37 (3) ◽  
pp. 259-271 ◽  
Author(s):  
Y. Koumya ◽  
R. Idouhli ◽  
M. Khadiri ◽  
A. Abouelfida ◽  
A. Aityoub ◽  
...  

AbstractStainless steel (SS) is a very corrosion-resistant alloy used in different industrial plants because of its chemical and mechanical properties. However, the high chloride concentration in sulfuric acid (H2SO4) may promote both general corrosion and pitting corrosion. The pitting corrosion susceptibility in SS in chlorinated H2SO4 and the effect of Euphorbia echinus extract (EEE) on both general corrosion and pitting corrosion have been studied using potentiodynamic polarization, electrochemical impedance spectroscopy, chronoamperometry, cyclic voltammetry, and scanning electron microscopy (SEM). The pitting potential has been found to shift slightly in the presence of chloride ions (Cl−) in H2SO4. Also, pitting corrosion initiation has been demonstrated in the recorded chronoamperograms as a linear straight line having a positive slope. EEE has reduced the general corrosion and the inhibitor adsorption was found to follow the Langmuir isotherm. SEM micrographs showed that the tested inhibitor has efficiently acted on pitting corrosion for different concentrations of Cl−. Also, the kinetic findings were in good agreement with the surface analysis data. Fourier transform infrared spectroscopy and ultraviolet-visible absorption spectrophotometric measurements provided more insights on the interaction between the chemical functional groups of the inhibitor and the SS surface.


2018 ◽  
Vol 2018 ◽  
pp. 1-11 ◽  
Author(s):  
Alvaro A. Rodriguez ◽  
Joseph H. Tylczak ◽  
Michael C. Gao ◽  
Paul D. Jablonski ◽  
Martin Detrois ◽  
...  

The corrosion behavior of high-entropy alloys (HEAs) CoCrFeNi2 and CoCrFeNi2Mo0.25 was investigated in 3.5 wt. percent sodium chloride (NaCl) at 25°C by electrochemical methods. Their corrosion parameters were compared to those of HASTELLOY® C-276 (UNS N10276) and stainless steel 316L (UNS 31600) to assess the suitability of HEAs for potential industrial applications in NaCl simulating seawater type environments. The corrosion rates were calculated using corrosion current determined from electrochemical experiments for each of the alloys. In addition, potentiodynamic polarization measurements can indicate active, passive, and transpassive behavior of the metal as well as potential susceptibility to pitting corrosion. Cyclic voltammetry (CV) can confirm the alloy susceptibility to pitting corrosion. Electrochemical impedance spectroscopy (EIS) elucidates the corrosion mechanism under studied conditions. The results of the electrochemical experiments and scanning electron microscopy (SEM) analyses of the corroded surfaces revealed general corrosion on alloy CoCrFeNi2Mo0.25 and HASTELLOY C-276 and pitting corrosion on alloy CoCrFeNi2 and stainless steel 316L.


Alloy Digest ◽  
2011 ◽  
Vol 60 (12) ◽  

Abstract Kubota Alloy HD (UNS J93005) is a heat-resisting stainless steel casting alloy suitable for long-term service at temperatures up to 1095 deg C (2000 deg F). The nearest wrought equivalent is type 327. This datasheet provides information on composition, physical properties, hardness, and tensile properties as well as creep. It also includes information on corrosion resistance as well as casting and joining. Filing Code: SS-1110. Producer or source: Kubota Metal Corporation, Fahramet Division.


Sign in / Sign up

Export Citation Format

Share Document