Effects of Speed Bumps and Humps on Motorcycle Speed Profiles

2014 ◽  
Vol 931-932 ◽  
pp. 536-540 ◽  
Author(s):  
Wichuda Satiennam ◽  
Thaned Satiennam ◽  
Pornsiri Urapa ◽  
Tussawan Phacharoen
Keyword(s):  
Developing Countries ◽  
Developed Countries ◽  
Vehicle Speed ◽  
Passenger Car ◽  
The Road ◽  
Acceleration Rate ◽  
Major Mode ◽  
Before And After ◽  
On The Road ◽  
Speed Humps

In developed countries, the use of speed humps and bumps have evolved from extensive research and testing which been properly designed and standardized. On the contrary in developing countries, no systematic and scientific studies have been carried out on that environment, especially the study on the effects that the motorcyclists response to the humps and bumps. This study therefore reveals the riders behavior when negotiating their speed to the devices. A case study was conducted in the provincial cities of Thailand where the motorcycle was a major mode of transportation. Six locations with speed humps and bumps were selected. Vehicles passing times were simultaneously recorded at 12 points along each traffic calmed link. From these data, a speed profile for each individual vehicle and for a link could be derived. It is found that speed humps and bumps have critically different impacts on motorcycle rider and passenger car driver. The smaller size speed bumps could effectively control the rider speed but have diverse impacts on the driver. These speed differences could post more safety deficiency to the site. The effect of the device on riders behavior, however, is restricted to a short spatial range (about 20-30 m before and after the device). For the speed humps, the motorcycle speeds are quite varied depending mainly on the road terrain. It is found that the motorcyclists have significant lower acceleration rate on the upgrade terrain when compared to the passenger car. Therefore, it is important to take all these rider characteristics into considerations when design the road humps to control vehicle speed in the developing countries.

Sensor Based Accident Prevention System

2020 ◽  
Vol 17 (4) ◽  
pp. 1720-1724
Author(s):  
M. Nithya ◽  
N. Pooranam ◽  
R. Deepalakshmi ◽  
M. Aruna Rani ◽  
S. Anandha Swarna
Keyword(s):  
Developing Countries ◽  
Cause Of Death ◽  
Accident Prevention ◽  
Vehicle Speed ◽  
Led Light ◽  
The Road ◽  
Prevention System ◽  
The World ◽  
On The Road ◽  
The One

In the developing countries accident is the major cause of death. The top 10 dangerous roads in the world are mountain roads and curve roads. In the mountain roads there will be tight curves and the roads will be narrow. In these kinds of situations the driver of a vehicle cannot see vehicles coming from opposite side. Thousands of people lose their lives each year because of this problem. The mountain roads might lead to a cliff. The solution for this problem is alerting the driver about the vehicle coming from opposite side in the hair-pin bends. That can be performed by placing the ultrasonic sensor on the road in one side before the road curve and then will keep the LED light after that curve, thus the vehicle which comes from the one end of the curve, the sensors which is present in that curve will sense and makes the LED light glows along with that buzzer sound and also vehicle speed is displayed at the opposite side. By looking at the LED light on signal driver can become alert and can slow down the speed of the vehicle. Thus it saves more lives.

CREATING WALKING LED TRANSIT STATIONS FOR WOMEN IN MALAYSIA

2020 ◽  
Vol 7 (1) ◽  
pp. 99
Author(s):  
Yong Adilah Shamsul Harumain ◽  
Nur Farhana Azmi ◽  
Suhaini Yusoff
Keyword(s):  
Quality Of Life ◽  
Developing Countries ◽  
Public Transportation ◽  
Carbon Emission ◽  
The Other ◽  
Walking Distance ◽  
The Road ◽  
On The Road ◽  
Female User

Transit stations are generally well known as nodes of spaces where percentage of people walking are relatively high. The issue is do more planning is actually given to create walkability. Creating walking led transit stations involves planning of walking distance, providing facilities like pathways, toilets, seating and lighting. On the other hand, creating walking led transit station for women uncover a new epitome. Walking becomes one of the most important forms of mobility for women in developing countries nowadays. Encouraging women to use public transportation is not just about another effort to promote the use of public transportation but also another great endeavour to reduce numbers of traffic on the road. This also means, creating an effort to control accidents rate, reducing carbon emission, improving health and eventually, developing the quality of life. Hence, in this paper, we sought first to find out the factors that motivate women to walk at transit stations in Malaysia. A questionnaire survey with 562 female user of Light Railway Transit (LRT) was conducted at LRT stations along Kelana Jaya Line. Both built and non-built environment characteristics, particularly distance, safety and facilities were found as factors that are consistently associated with women walkability. With these findings, the paper highlights the criteria  which are needed to create and make betterment of transit stations not just for women but also for walkability in general.

scholarly journals Measures to optimize traffic and the environment. Calculations of environmental safety on a given section of the Rostov-on-Don road network

2020 ◽  
pp. 68-77
Author(s):  
R. S. Durov ◽  
◽  
E. V. Varnakova ◽  
K. O. Kobzev ◽  
◽  
...  
Keyword(s):  
Road Network ◽  
Road Transport ◽  
Environmental Safety ◽  
Environmental Indicators ◽  
Nox Emissions ◽  
The Road ◽  
Before And After ◽  
Reduce Emissions ◽  
On The Road ◽  
State Of The Environment

Introduction. One of the most pressing socio-economic problems is the state of the environment, which affects the living conditions of many people. The article deals with the problem areas of the intersection of 20-ya Liniya street – Sholokhov Avenue in Rostov-on-Don. Problem Statement. The purpose of this paper is to improve environmental safety at the intersection of 20-ya Liniya street – Sholokhov Avenue in Rostov-on-Don by reducing emissions from road transport through the proposed measures to reorganize traffic on this section of the road network. Theoretical Part. The article provides an assessment of environmental and road safety on the road network section before applying the proposed measures. The measures are listed and justified that would help improve the conditions for road transport at the selected intersection and reduce emissions from road transport, which would improve environmental safety. The calculation of environmental indicators was made after the proposed measures to reduce NOx emissions by cars. Conclusion. The article analyzes the environmental indicators before and after the events, and then compares them. Based on the analysis and calculations, it is determined how much the proposed measures to optimize traffic will help reduce NOx emissions by cars.

Determining Passenger Car Equivalent for Motorcycle at Mid-Block of Sesetan Road

2015 ◽  
Vol 776 ◽  
pp. 95-100
Author(s):  
I. Gusti Raka Purbanto
Keyword(s):  
Motor Vehicles ◽  
Heavy Vehicles ◽  
Highway Capacity ◽  
Passenger Car ◽  
Highway Capacity Manual ◽  
The Road ◽  
Traffic Conditions ◽  
Mode Share ◽  
Passenger Car Equivalent ◽  
On The Road

Motorcycle dominates traffic in Bali, particularly in urban roads, which occupy more than 85% of mode share. The three types of vehicles, i.e. motorcycles, heavy and light vehicles share the roadways together. Under mixed traffic conditions, motorcycle may be travelling in between and alongside two consecutive motor vehicles. Considering such a situation, passenger car equivalent values should be examined thoroughly. This study aims to determine passenger car equivalent (PCEs) of motorcycle at mid-block of Sesetan Road. Three approaches are used to examine the PCEs values. This study found that the PCE of motorcycles are in a range between 0.2 and 0.4. This values are about the same to the existing PCE of the Indonesian Highway Capacity Manual (1997). This study also pointed out that motorcyclists and car drivers may behave differently to the existence of motorcycles. Car drivers are more aware than motorcyclists on the existence of motorcycle on the road. Further, more samples are required to obtain comprehensive results. In addition, the presence of heavy vehicles need to be considered for future study.

Occurrence and Prevention of Changes in the Chemical Structure of Natural Rubber Tire Tread Vulcanizates during Service

1970 ◽  
Vol 43 (5) ◽  
pp. 1215-1224 ◽  
Author(s):  
J. I. Cunneen ◽  
R. M. Russell
Keyword(s):  
Chemical Structure ◽  
Main Chain ◽  
Heavy Duty ◽  
Structural Alterations ◽  
The Road ◽  
Rubber Tire ◽  
Before And After ◽  
On The Road ◽  
The Stability ◽  
Made In

Abstract The chemical structure of the tread vulcanizate of heavy-duty tires has been investigated before and after service on the road, and after testing under conditions designed to induce tread-lift. Significant changes occurred. These included a marked reduction in the concentration of polysulfide crosslinks, and an increase in the amount of monosulfide crosslinks and main chain modification. Experiments with vulcanizates made in the laboratory indicated that the structural alterations in the tires were due to thermal anaerobic reactions caused by heat build-up, and that they resulted in a deterioration in some of the physical properties of the tread vulcanizate. The rate of desulfuration of ‘model’ polysulfides has been found to depend critically upon the nature of the vulcanization recipe. These novel findings point the way to improving the stability of vulcanizates used in the treads of tires and, consequently, tire performance.

Influence of Silica Sand Particles on Disc Brake Squeal Noise

2013 ◽  
Vol 471 ◽  
pp. 81-85 ◽  
Author(s):  
Ahmad Razimi Mat Lazim ◽  
Abd Rahim Abu Bakar ◽  
Mohd Kameil Abdul Hamid ◽  
Izzat Mohd Asri
Keyword(s):  
Surface Condition ◽  
Surface Characteristics ◽  
Silica Sand ◽  
Brake Pad ◽  
Brake Squeal ◽  
The Road ◽  
Film Distribution ◽  
Before And After ◽  
Sand Particles ◽  
On The Road

Researchers in recent years begin to explore on tribological behavior of automotive brake squeal phenomena which covers the morphology, chemical composition, friction and wear, phase composition and third body or friction film distribution. However less effort has been made to study the tribological on the influence of small particles on brake squeal. During braking condition, both rotor and pads are exposed to road environmental particle which may affect pads surface condition. In order to assess the influence of this particle on brake squeal a series of squeal tests were performed. Silica sand grit particles with a size range between 400 to 200 μm which most available on the road surface were used in this experiment. Brake pad and disc surface characteristics were analyzed before and after squealing condition using Scanning Electron Microscope (SEM) and Energy dispersive X-ray analysis (EDX). The result shows that the silica sand particles had influence the squeal and surface behavior of the brake pad.

Analysis of Dynamic Load Level of High-Speed Heavy Vehicle Imposed on Uneven Pavement

2011 ◽  
Vol 138-139 ◽  
pp. 146-152
Author(s):  
Guo He Guo ◽  
Yu Feng Bai ◽  
Tao Wang
Keyword(s):  
Dynamic Load ◽  
High Speed ◽  
Load Level ◽  
Heavy Vehicle ◽  
Vehicle Speed ◽  
Destructive Effect ◽  
The Road ◽  
Wide Range ◽  
On The Road ◽  
Factor Interaction

Based on the significant destructive effect of heavy vehicle on uneven roads, two simplified models of pavement unevenness and vehicle dynamic load were established in accordance with D'A lembert principle, and Matlab software was used to analyze the changing law of dynamic load under the conditions of different road unevenness, vehicle speed and load. The results show that vehicles running on uneven road may produce more cumulative damages than static load, and DLC (dynamic load coefficient) changes in wide range, maximum up to 2.0 or more; the effect of speed and load on dynamic load is complex, and due to multi-factor interaction, DLC doesn’t consistently increase or decrease with speed and load increasing. Although the dynamic load level caused by high-speed heavy vehicle is not necessarily too high, its impact on the road can not be ignored.

scholarly journals THE BITUMEN BATCHING SYSTEM'S MODERNIZATION AND ITS EFFECTIVE ANALYSIS AT THE ASPHALT MIXING PLANT

Transport ◽  
2010 ◽  
Vol 25 (3) ◽  
pp. 325-335 ◽  
Author(s):  
Justas Bražiūnas ◽  
Henrikas Sivilevičius
Keyword(s):  
Asphalt Concrete ◽  
Additive Model ◽  
Technological Parameters ◽  
Destructive Effect ◽  
The Road ◽  
Weighted Matrix ◽  
Bitumen Content ◽  
Before And After ◽  
On The Road ◽  
And Performance

Some particular aspects such as the improvement methods of technological parameters for hot bitu‐ men storage in a pipeline transport system, transportation and dosed supply to batch asphalt mixing plant (AMP) are evaluated in this paper. Bitumen in asphalt concrete binds together the material of mineral particles into a strong conglomerate of a complicated structure, capable of withstanding the destructive effect of vehicles and the factors on the road pavements. The optimal amount of bitumen determined by calculation and laboratory testing should be maintained in mix batches of hot‐mix asphalt (HMA) obtained from AMP mixer. In the periodic type of the asphalt concrete blender mass of the weighted matrix in the all merging batcher's tanks should correspond in percents equally in the HMA to the designed amount of the job‐mix formula (JMF). The bitumen batcher does not always weigh bitumen portions precisely. Their mass deviations from the amount determined by JMF and its variation impair HMA composition and performance. In addition,, an additive model for calculating the effect of factors causing the variance of bitumen content in the produced HMA mixture is presented in this current paper as well. The data on statistical evaluation of bitumen batcher's modernization performed at certain Lithuanian Enterprise are discussed. The differences in structures of reconstructed and not reconstructed bitumen batching systems (BBS) are analysed and methods of determining modernization effectiveness are presented. The effectiveness of BBS is analysed too, defining the deviations of bitumen content in subsamples, taken and extracted everyday for two seasons (before and after the batcher's modernization) of HMA mixture production from the value of JMF and comparing them to the values of tolerances. The analysis of column charts and histograms shows that the made modernization helped to increase the precision of supplying the required amount of bitumen to HMA mixture insignificantly. However, the control of BBS has been considerably increased.

Study on the Dynamic Wheel Load of Multi-Axle Vehicle Based on Distribute Loading Weight

2010 ◽  
Vol 159 ◽  
pp. 35-40
Author(s):  
Zhong Hong Dong
Keyword(s):  
Dynamic Load ◽  
Influence Factors ◽  
Vehicle Speed ◽  
Tire Pressure ◽  
Wheel Load ◽  
The Road ◽  
Road Roughness ◽  
Tire Stiffness ◽  
On The Road

To study the dynamic wheel load on the road, a dynamic multi-axle vehicle mode has been developed, which is based on distribute loading weight and treats tire stiffness as the function of tire pressure and wheel load. Taking a tractor-semitrailer as representative, the influence factors and the influence law of the dynamic load were studied. It is found that the load coefficient increases with the increase of road roughness, vehicle speed and tire pressure, yet it decreases with the increase of axle load. Combining the influences of road roughness, vehicle speed, axle load and tire pressure, the dynamic load coefficient is 1.14 for the level A road, 1.19 for the level B road, 1.27 for the level C road, and 1.36 for the level D road.

scholarly journals Concept of queue clearance rate for estimation of equivalency factors at priority junctions

2016 ◽  
Vol 43 (7) ◽  
pp. 593-598 ◽  
Author(s):  
Mithun Mohan ◽  
Satish Chandra
Keyword(s):  
Developing Countries ◽  
Clearance Rate ◽  
Developed Countries ◽  
Traffic Volume ◽  
Heterogeneous Traffic ◽  
Passenger Cars ◽  
Passenger Car ◽  
Traffic Conditions ◽  
Equivalency Factors ◽  
Equivalent Number

Traffic in developing countries is often distinguished from others for its diversity in vehicular composition and passenger car equivalents (PCE) becomes essential in such conditions for expressing traffic volume in terms of equivalent number of passenger cars. The PCE estimation at two-way stop-controlled intersections in developing countries is further complicated by the lack of movement priority and lane discipline. The study introduces a method to find PCE factors based on the time taken by a queue of vehicles to completely clear the intersection and composition of the queue. The method is validated through simulations in VISSIM software and was then used to derive PCE factors for three intersections in India. Although the method is developed and tested to estimate PCE factors under highly heterogeneous traffic at priority junctions in India, it is quite general in nature and can be used in traffic conditions found in developed countries as well.

Sign in / Sign up

Export Citation Format

Share Document