Fatigue Life Assessments of the AISI 1513 Carbon Steel Subjected to Road Surface Strains

2020 ◽  
Vol 402 ◽  
pp. 39-44
Author(s):  
Teuku Edisah Putra ◽  
Husaini ◽  
Muhammad Ikbal ◽  
Iskandar Hasanuddin ◽  
Muhammad Rizal ◽  
...  
Keyword(s):  
Fatigue Life ◽  
Carbon Steel ◽  
Strain Gauge ◽  
Road Surface ◽  
Vertical Load ◽  
The Road ◽  
Road Surfaces ◽  
Cycles To Failure

The purpose of this work was to predict the fatigue life of the AISI 1513 carbon steel due to the strains measured at a vehicle's lower arm. The strain signals were acquired using a strain gauge installed at the lower arm, and then the car was driven at various road surfaces. On the smooth road surface, the car was driven at a speed of > 70 km/h and on the rough road surface, at a speed of < 20 km/h. The results show that when the vehicle was driven on the rough road, the lower arm received higher stress, which provided a shorter fatigue life. The contour of the road surfaces provided a vertical load, directly working the lower arm and reducing the load vertically. The fatigue life for the rough road surface was 13,050 cycles to failure. This value was 91,195% lower than the fatigue life on the smooth road surface.

Prediction of the Fatigue Life of the SAE 5160 Carbon Steel Coil Spring Based on Strain-Life Approach

2020 ◽  
Vol 841 ◽  
pp. 381-386
Author(s):  
Teuku Edisah Putra ◽  
Husaini ◽  
Hary Prakasa
Keyword(s):  
Fatigue Life ◽  
Carbon Steel ◽  
Critical Point ◽  
Strain Gauge ◽  
Road Surface ◽  
Coil Spring ◽  
Steel Coil ◽  
Cycles To Failure

This study aims to identify the effect of road surface to coil spring fatigue life using the strain-life approach. Strain signals were measured by attaching a strain gauge at the critical point of the component. The car was driven on a flat road, as well as uphill, and downhill paths. The results show that the downhill road provided the lowest fatigue life, of 1.5E+4 cycles to failure, which was 53 % lower than that of the uphill and 2,233 % lower than the flat road owing to the braking factor which resulted in a higher stress to the coil spring.

Fatigue Life Assessments of the AISI 1513 Carbon Steel of a Vehicle Lower Arm Subjected to Clockwise and Counter-Clockwise Road Strains

2020 ◽  
Vol 402 ◽  
pp. 45-49
Author(s):  
Husaini ◽  
Teuku Edisah Putra ◽  
Muhammad Reza Rizky ◽  
Rauzatul Akmal ◽  
Iskandar Hasanuddin ◽  
...  
Keyword(s):  
Fatigue Life ◽  
Carbon Steel ◽  
Strain Gauge ◽  
The Right ◽  
Cycles To Failure

This study aims to predict the fatigue life of the AISI 1513 carbon steel as the material for the vehicle lower arm subjected to road strains. Measurement of the strain signals was done by attaching a strain gauge at the left lower arm and driving the vehicle on clockwise and counter-clockwise roads at a speed of 30 km/h. According to the results based on the strain-life approach, the clockwise road gave the fatigue life of 2,600,000 cycles to failure, which was 1,862 % lower than the counter-clockwise road. It indicated that when the vehicle turned to the right, the lower arm on the left side subjected to a higher strain, resulting in a shorter fatigue life.

Fatigue Life Assessments of the SAE 5160 Carbon Steel Subjected to Uphill and Downhill Roads Strains

2020 ◽  
Vol 402 ◽  
pp. 33-38
Author(s):  
Teuku Edisah Putra ◽  
Husaini ◽  
Hary Prakasa ◽  
Iskandar Hasanuddin ◽  
Muhammad Rizal ◽  
...  
Keyword(s):  
Fatigue Life ◽  
Carbon Steel ◽  
Strain Gauge ◽  
Life Assessment ◽  
Coil Spring ◽  
Fatigue Life Assessment ◽  
Cycles To Failure

This study examines the fatigue life of the SAE 5160 carbon steel as the material for an automotive coil spring subjected to road strain. The strain signals were acquired by attaching a strain gauge on the component, driving a car up- and down-hill roads. The results of the fatigue life assessment based on the strain-life approach show that the downhill road resulted in a lifespan of 15,000 cycles to failure, which was 53% lower than the uphill road. This value was a result of braking when the vehicle is moving downhill, causing stress to the component leading to shorter fatigue life.

Tire-Road Interactions — Harmony or Conflict?

1989 ◽  
Vol 17 (1) ◽  
pp. 66-84
Author(s):  
A. R. Williams
Keyword(s):  
Rolling Resistance ◽  
Major Effect ◽  
Road Surface ◽  
Interactive Effects ◽  
Central Theme ◽  
Water Drainage ◽  
The Road ◽  
Truck Tires ◽  
Road Surfaces ◽  
Tire Wear

Abstract This is a summary of work by the author and his colleagues, as well as by others reported in the literature, that demonstrate a need for considering a vehicle, its tires, and the road surface as a system. The central theme is interaction at the footprint, especially that of truck tires. Individual and interactive effects of road and tires are considered under the major topics of road aggregate (macroscopic and microscopic properties), development of a novel road surface, safety, noise, rolling resistance, riding comfort, water drainage by both road and tire, development of tire tread compounds and a proving ground, and influence of tire wear on wet traction. A general conclusion is that road surfaces have both the major effect and the greater potential for improvement.

scholarly journals Laboratory experiment on the nano-TiO2 photocatalytic degradation effect of road surface oil pollution

2020 ◽  
Vol 9 (1) ◽  
pp. 922-933
Author(s):  
Qing’e Wang ◽  
Kai Zheng ◽  
Huanan Yu ◽  
Luwei Zhao ◽  
Xuan Zhu ◽  
...  
Keyword(s):  
Photocatalytic Degradation ◽  
Oil Pollution ◽  
Road Surface ◽  
Test Method ◽  
Driving Safety ◽  
The Road ◽  
Road Surfaces ◽  
The Many ◽  
The Impact ◽  
Degradation Effect

AbstractOil leak from vehicles is one of the most common pollution types of the road. The spilled oil could be retained on the surface and spread in the air voids of the road, which results in a decrease in the friction coefficient of the road, affects driving safety, and causes damage to pavement materials over time. Photocatalytic degradation through nano-TiO2 is a safe, long-lasting, and sustainable technology among the many methods for treating oil contamination on road surfaces. In this study, the nano-TiO2 photocatalytic degradation effect of road surface oil pollution was evaluated through the lab experiment. First, a glass dish was used as a substrate to determine the basic working condition of the test; then, a test method considering the impact of different oil erosion degrees was proposed to eliminate the effect of oil erosion on asphalt pavement and leakage on cement pavement, which led to the development of a lab test method for the nano-TiO2 photocatalytic degradation effect of oil pollution on different road surfaces.

A new procedure for determining the road surface reduced luminance coefficient table by on-site measurements

2018 ◽  
Vol 51 (1) ◽  
pp. 65-81 ◽  
Author(s):  
N Strbac-Hadzibegovic ◽  
S Strbac-Savic ◽  
M Kostic
Keyword(s):  
Road Surface ◽  
Surface Reflection ◽  
The Road ◽  
Road Lighting ◽  
Average Luminance ◽  
Road Surfaces ◽  
Q Values

Numerous measurements have shown that the standard R classes do not represent adequately many road surfaces used nowadays. Therefore, the construction of portable reflectometers intended for on-site measurements of road surface reflection properties has been given particular attention during the last decade. This paper presents a new procedure for the improvement of the accuracy of such a portable reflectometer. Optimally extrapolating the values of the 20 luminance coefficients (q), each measured by the portable reflectometer for a set of angles of observation (α = 5°–80°), the 20 q-values referring to α = 1° are calculated. This enables their comparison with the corresponding q elements from each of the 447 reduced q-tables derived from the available r-table database, obtained by using a precise laboratory reflectometer on a wide variety of road samples. Selecting the closest reduced q-table, the corresponding r-table and the actual average luminance coefficient can be determined. In order to validate the proposed procedure, which can also be applied to other similar portable reflectometers, measurements of the luminance and overall and longitudinal luminance uniformities were carried out on eleven road-lighting installations. They showed that the results obtained by this procedure deviate only slightly from those obtained using r-tables determined by the laboratory reflectometer.

Observations on the Physical Aspects of Resistance to Skidding on Dry Roads and Particularly on Wet Roads

1956 ◽  
Vol 29 (4) ◽  
pp. 1425-1433 ◽  
Author(s):  
K. Knauerhase
Keyword(s):  
Great Influence ◽  
Boundary Surface ◽  
Road Surface ◽  
Motor Vehicles ◽  
Vector Diagram ◽  
Surface Adhesion ◽  
The Road ◽  
Wet Friction ◽  
Road Surfaces ◽  
Wetting Power

Abstract To ensure safety from skidding, attention has up to now been devoted to building rough surface roads, to the development of the proper vehicle construction with respect to this feature, and to the factor most directly involved, the tires. Special attention has been directed in connection with this latter phase to a much more open tread patterning and to the effect of decreasing tire inflation, both of which affect the life of the tire adversely. These steps neglected to take advantage of the physical effect of adhesion, which, without lowering the durability, now makes possible an enhanced contribution to the cohesive friction by the profile grooves which are of necessity retained to keep the weight down. The goal is, therefore, to provide the smooth surfaces of the tread pattern that come in contact with the road with the greatest possible physical gripping power, or adhesion. After illustrating the interfacial magnitudes with the help of a vector diagram, we shall survey the laws of boundary surface adhesion. Here the great influence of the liquid involved in wet friction becomes clear and the particularly favorable interfacial tension property of water can be assessed. Since skidding can occur only at the interfaces : rubber-water, or water-road, the requirement is as follows : both the greatest possible wetting power between rubber and water, and also between water and road surface, that is, hydrophilic properties in the rubber and hydrophilic road surfaces, in order to reduce the danger of skidding. Good insurance against skidding requires hydrophilic rubber and a hydrophilic road surface, for a tire that has been developed to be nonskidding holds on a hydrophilic road surface and skids on a hydrophobic road surface. A hydrophobic tire, on the other hand, skids on any wet road. Although considerable advances have been made with respect to safety from skidding since rubber tires were first developed for motor vehicles, with increase of speeds this problem demands our attention to a greater and greater degree. Safety from skidding can result only from the combined efforts of road and car builders, tire makers, and the chemists and physicists of all three groups.

scholarly journals Perceiving Excitation Characteristics from Interactions between Field Road and Vehicle via Vibration Sensing

2021 ◽  
Vol 2021 ◽  
pp. 1-14
Author(s):  
Yuansheng Cheng ◽  
Xiaoqin Li ◽  
Xiaolan Man ◽  
Feifan Fan ◽  
Zhixiong Li
Keyword(s):  
Vibration Response ◽  
Road Surface ◽  
Vibration Test ◽  
Agricultural Vehicles ◽  
The Road ◽  
Effective Roughness ◽  
Long Wave ◽  
Road Surfaces ◽  
Road Excitation ◽  
Wave Surfaces

When agricultural vehicles operate in the field, the soft road excitation makes it difficult to measure the vehicle vibration. A camera-accelerator system can solve this issue by utilizing computer vision information; however, the relationship between the field road surface and the vehicle vibration response remains an unsolved problem. This study aims to investigate the correlation of the soft road excitation of different long-wave surfaces with the vehicle vibration response. Vibration equation between the vehicle and soft road surface system was established to produce an effective roughness model of the field soft road surface. In order to simulate the vehicle vibration state under different long-wave road surfaces, the soil rectangular pits with 21 kinds of different spans and depths were applied to the road surfaces, and a tractor vibration test system was built for vibration test. The frequency spectrum analysis was performed for the vibration response and the roughness signals of the road surfaces. The results showed that coefficient (R2) of frequency correlation between the roughness excitation and the original unevenness at the excitation point at the rear end of the rectangular soil pit fell within 0.9641∼0.9969. The main frequency band of the vibration response fell within 0∼3 Hz, and the phenomenon of quadruple frequency existed. The correlation of roughness excitation with quadruple frequency fell within 0.992165∼1. The primary excitation points were located at the rear end of the rectangular soil pit. In addition, it also indicated that when the vehicle was driven without autonomous power, the vehicle vibration frequency mainly depended on the excitation frequency of the field road surface and the frequency at the maximum vehicle vibration intensity was 2 or 3 times of that at the maximum field soft road excitation. These findings may provide a reference for optimal design of vibration reduction and control for agricultural vehicles.

On the applicability of a scan-based mobile mapping system for monitoring the planarity and subsidence of road surfaces – Pilot study on the A44n motorway in Germany

2020 ◽  
Vol 14 (1) ◽  
pp. 39-54 ◽  
Author(s):  
Erik Heinz ◽  
Christian Eling ◽  
Lasse Klingbeil ◽  
Heiner Kuhlmann
Keyword(s):  
Standard Deviation ◽  
Point Clouds ◽  
Road Surface ◽  
Control Points ◽  
Mobile Mapping ◽  
The Road ◽  
Mapping System ◽  
Road Surfaces ◽  
Mobile Mapping System ◽  
Physical Height

AbstractKinematic laser scanning is widely used for the fast and accurate acquisition of road corridors. In this context, road monitoring is a crucial application, since deficiencies of the road surface due to non-planarity and subsidence put traffic at risk. In recent years, a Mobile Mapping System (MMS) has been developed at the University of Bonn, consisting of a GNSS/IMU unit and a 2D laser scanner. The goal of this paper is to evaluate the accuracy and precision of this MMS, where the height component is of main interest. Following this, the applicability of the MMS for monitoring the planarity and subsidence of road surfaces is analyzed. The test area for this study is a 6 km long section of the A44n motorway in Germany. For the evaluation of the MMS, leveled control points along the motorway as well as point cloud comparisons of repeated passes were used. In order to transform the ellipsoidal heights of the MMS into the physical height system of the control points, undulations were utilized. In this respect, a local tilt correction for the geoid model was determined based on GNSS baselines and leveling, leading to a physical height accuracy of the MMS of < 10 mm (RMS). The related height precision has a standard deviation of about 5 mm. Hence, a potential subsidence of the road surface in the order of a few cm is detectable. In addition, the point clouds were used to analyze the planarity of the road surface. In the course of this, the cross fall of the road was estimated with a standard deviation of < 0.07 %. Yet, no deficiencies of the road surface in the form of significant rut depths or fictive water depths were detected, indicating the proper condition of the A44n motorway. According to our tests, the MMS is appropriate for road monitoring.

Stress Analysis on an Automotive Coil Spring Driven on Flat, Uphill, and Downhill Road Surfaces

2021 ◽  
Vol 892 ◽  
pp. 124-128
Author(s):  
Harahap Jagodang ◽  
Husaini ◽  
Edisah Putra Teuku ◽  
Dieter Schramm
Keyword(s):  
Carbon Steel ◽  
Dynamic Analysis ◽  
Stress Analysis ◽  
Maximum Stress ◽  
Road Surface ◽  
Coil Spring ◽  
Vehicle Load ◽  
Road Surfaces ◽  
Dynamic Analyses

This study aims to analyze the stress that occurred on the automotive coil spring made of SAE 5160 carbon steel due to various types of road surfaces. The 60-second strain signals measured on a coil spring of a car being driven on a flat, uphill, and downhill road surface were used as the loads in these dynamic analyses. The analysis results showed that the maximum stress occurred on the inside of the spring in the second coil from the top. The results of this dynamic analysis also showed that the three types of road surfaces provided almost the same stress. The downhill road surface gave the highest stress, which was 0.622 GPa, followed by flat road (0.621 GPa) and uphill road (0.62 GPa). The reasons for this are the shifting of the vehicle load to the front wheels together with the braking effect when driving downhill.

Sign in / Sign up

Export Citation Format

Share Document