Mechanical Properties of Granite-Gravel Porous Concrete

2021 ◽  
Vol 57 ◽  
pp. 115-123
Author(s):  
Samson Olalekan Odeyemi
Keyword(s):  
Compressive Strength ◽  
Coarse Aggregate ◽  
Optimal Combination ◽  
Control Surface ◽  
Control Specimen ◽  
Cement Ratio ◽  
Porous Concrete ◽  
Design Expert ◽  
Optimal Mix ◽  
Percentage Porosity

The need for porous concrete has become increased due its ability to control surface water, increase the rate of recharging groundwater, and reduce pollution of the ecosystem. Granite is a coarse aggregate that is quite expensive when compared with gravel in Nigeria. Therefore, this research is aimed at optimizing blended granite and gravel in the production of porous concrete. Samples of blended granite-gravel porous concrete of varying mix proportions were produced using cement to aggregate mix ratio of 1:4. The samples were tested for their porosity, workability and compressive strengths. The data collected were analyzed with the aid of Design Expert 10.0. It was observed that the optimal combination for the granite-gravel blended porous concrete is 12% granite, 88% gravel, and a water-cement ratio of 0.66%. This combination gave a porous concrete with a compressive strength of 48.4 N/mm2, percentage porosity of 6% and a compacting factor of 0.91. These values when compared to that of the control specimen revealed that the optimal mix gave a porous concrete with higher porosity, higher workability and a better compressive strength.

scholarly journals Relation between Density and Compressive Strength of Foamed Concrete

Materials ◽  
2021 ◽  
Vol 14 (11) ◽  
pp. 2967
Author(s):  
Rokiah Othman ◽  
Ramadhansyah Putra Jaya ◽  
Khairunisa Muthusamy ◽  
MohdArif Sulaiman ◽  
Youventharan Duraisamy ◽  
...  
Keyword(s):  
Compressive Strength ◽  
Building Materials ◽  
Bleaching Earth ◽  
Concrete Specimen ◽  
Control Specimen ◽  
Dilution Ratio ◽  
Sustainable Building ◽  
Cement Ratio ◽  
Foamed Concrete ◽  
Partial Cement Replacement

This study aims to obtain the relationship between density and compressive strength of foamed concrete. Foamed concrete is a preferred building material due to the low density of its concrete. In foamed concrete, the compressive strength reduces with decreasing density. Generally, a denser foamed concrete produces higher compressive strength and lower volume of voids. In the present study, the tests were carried out in stages in order to investigate the effect of sand–cement ratio, water to cement ratio, foam dosage, and dilution ratio on workability, density, and compressive strength of the control foamed concrete specimen. Next, the test obtained the optimum content of processed spent bleaching earth (PSBE) as partial cement replacement in the foamed concrete. Based on the experimental results, the use of 1:1.5 cement to sand ratio for the mortar mix specified the best performance for density, workability, and 28-day compressive strength. Increasing the sand to cement ratio increased the density and compressive strength of the mortar specimen. In addition, in the production of control foamed concrete, increasing the foam dosage reduced the density and compressive strength of the control specimen. Similarly with the dilution ratio, the compressive strength of the control foamed concrete decreased with an increasing dilution ratio. The employment of PSBE significantly influenced the density and compressive strength of the foamed concrete. An increase in the percentage of PSBE reduced the density of the foamed concrete. The compressive strength of the foamed concrete that incorporated PSBE increased with increasing PSBE content up to 30% PSBE. In conclusion, the compressive strength of foamed concrete depends on its density. It was revealed that the use of 30% PSBE as a replacement for cement meets the desired density of 1600 kg/m3, with stability and consistency in workability, and it increases the compressive strength dramatically from 10 to 23 MPa as compared to the control specimen. Thus, it demonstrated that the positive effect of incorporation of PSBE in foamed concrete is linked to the pozzolanic effect whereby more calcium silicate hydrate (CSH) produces denser foamed concrete, which leads to higher strength, and it is less pore connected. In addition, the regression analysis shows strong correlation between density and compressive strength of the foamed concrete due to the R2 being closer to one. Thus, production of foamed concrete incorporating 30% PSBE might have potential for sustainable building materials.

Experimental Study on Compressive Strength of Recycled Aggregate Concrete

2008 ◽  
Vol 385-387 ◽  
pp. 381-384 ◽  
Author(s):  
Wei Wang ◽  
Hua Ling ◽  
Xiao Ni Wang ◽  
Tian Xia ◽  
Da Zhi Wang ◽  
...  
Keyword(s):  
Experimental Study ◽  
Compressive Strength ◽  
Coarse Aggregate ◽  
Recycled Aggregate Concrete ◽  
Time Dependent ◽  
Recycled Aggregate ◽  
Experimental Investigations ◽  
Aggregate Concrete ◽  
Cement Ratio ◽  
Practical Engineering

With the increase in the use of recycled aggregate concrete (RAC), it is necessary to clearly understand its behavior and characteristics. In this paper, experimental study on compressive strength of RAC with same water/cement ratio is conducted. Firstly, influence of recycled coarse aggregate contents on cube compressive strength of RAC is studied. Secondly, experiment on time-dependent strength developing process of RAC is conducted with different solidification ages. Finally, based on above experimental investigations, empirical formula for compress strengths of RAC with different ages is presented. The result of this paper is helpful to theoretical analysis and practical engineering design of RAC structures.

scholarly journals Effect of Water Cement Ratios on Compressive Strength of Palm Kernel Shell Concrete

2019 ◽  
Vol 2 (Issue 1) ◽  
Author(s):  
A.O Adeyemi ◽  
M.A Anifowose ◽  
I.O Amototo ◽  
S.A Adebara ◽  
M.Y Olawuyi
Keyword(s):  
Compressive Strength ◽  
Coarse Aggregate ◽  
Fresh Concrete ◽  
Palm Kernel ◽  
Hardened Concrete ◽  
Cement Ratio ◽  
Water Cement Ratio ◽  
Palm Kernel Shell ◽  
Compressive Strength Of Concrete ◽  
Palm Kernel Shells

This study examined the effect of varying water cement ratio on the compressive strength of concrete produced using palm kernel shell (PKS) as coarse aggregate at different replacement levels. The replacement levels of coarse aggregate with palm kernel shells (PKS) were 0%, 25%, 50%, and 100% respectively. PKS concrete cubes (144 specimens) of sizes 150mm x 150mm x 150mm were cast and cured in water for 7, 14, 21 and 28 days respectively. A mix ratio of 1:2:4 was adopted with water-cement ratio of 0.45, 0.5, and 0.6 respectively while the batching was done by weight. Slump test was conducted on fresh concrete while compressive strength test was carried out on the hardened concrete cubes using a compression testing machine of 2000kN capacity. The result of tests on fresh concrete shows that the slump height of 0.45 water cement ratio (w/c) increases with an increase in PKS%. This trend was similar to 0.50 and 0.60 w/c. However, the compressive strength of concrete cube decreases with an increase in w/c (from 0.45 to 0.60) but increases with respect to curing age and also decreases with increase in PKS%. Concrete with 0.45 water-cement ratio possess the highest compressive strength. It was observed that PKS is not a good substitute for coarse aggregate in mix ratio 1:2:4 for concrete productions. Hence, the study suggest the use of chemical admixture such as superplasticizer or calcium chloride in order to improve the strength of palm kernel shells-concrete.

scholarly journals Influence of Reduced Water Cement Ratio on Behaviour of Concrete Having Plastic Aggregate

2018 ◽  
Vol 4 (12) ◽  
pp. 2971 ◽  
Author(s):  
Saad Tayyab ◽  
Asad Ullah ◽  
Kamal Shah ◽  
Faial Mehmood ◽  
Akhtar Gul
Keyword(s):  
Compressive Strength ◽  
Coarse Aggregate ◽  
Stress Strain ◽  
Cement Ratio ◽  
Coarse Aggregates ◽  
Alternative Materials ◽  
Super Plasticizer ◽  
Strain Relationship ◽  
Natural Aggregates ◽  
Reduced Water

The production and use of plastic bottles is increasing tremendously with passing time. These plastic bottles become a problem when they are disposed as they are non-biodegradable. This means that the waste plastic, when dumped, does not decompose naturally and stays in the environment affecting the ecological system. The use of alternative aggregates like Plastic Coarse Aggregate (PCA) is a natural step in solving part of reduction of natural aggregates as well as to solve the issue discussed above. The researchers are trying from half a century to investigate the alternative materials to be replaced in concrete mixture in place of either aggregate or cement.  In this research, the concrete made from plastic waste as coarse aggregates were investigated for compressive strength and Stress-strain relationship. Plastic coarse aggregate have been replaced in place of natural coarse aggregate by different percentages with w/c 0.5, 0.4 and 0.3. The percentage replacement of plastic aggregate in place of mineral coarse aggregate was 25%, 30%, 35% and 40 %. Using Super-plasticizer Chemrite 520-BAS. OPC-53 grade cement was used. Total of forty five Cylinders were prepared based on different combination of Percentage of Plastic aggregate replaced and W/C as discussed above and checked for compressive strength and stress-strain relationship. The compressive strength increases by about 19.25% due to the decrease in W/C from 0.5 to 0.3 for plastic percentage addition of 40%.

scholarly journals Use of Recycled Tyre Rubber in Non-structural Concrete

2018 ◽  
Vol 203 ◽  
pp. 06001
Author(s):  
Muhammad Bilal Waris ◽  
Hussain Najwani ◽  
Khalifa Al-Jabri ◽  
Abdullah Al-Saidy
Keyword(s):  
Compressive Strength ◽  
Water Absorption ◽  
Coarse Aggregate ◽  
Partial Replacement ◽  
Fine Aggregate ◽  
Structural Concrete ◽  
Cement Ratio ◽  
Mix Proportion ◽  
Water To Cement Ratio ◽  
Concrete Blocks

To manage tyre waste and conserve natural aggregate resource, this research investigates the use of waste tyre rubber as partial replacement of fine aggregates in non-structural concrete. The research used Taguchi method to study the influence of mix proportion, water-to-cement ratio and tyre rubber replacement percentage on concrete. Nine mixes were prepared with mix proportion of 1:2:4, 1:5:4 and 1:2.5:3; water-to-cement ratio of 0.25, 0.35 and 0.40 and rubber to fine aggregate replacement of 20%, 30% and 40%. Compressive strength and water absorption tests were carried out on 100 mm cubes. Compressive strength was directly proportional to the amount of coarse aggregate in the mix. Water-to-cement ratio increased the strength within the range used in the study. Strength was found to be more sensitive to the overall rubber content than the replacement ratio. Seven out of the nine mixes satisfied the minimum strength requirement for concrete blocks set by ASTM. Water absorption and density for all mixes satisfied the limits applicable for concrete blocks. The study indicates that mix proportions with fine to coarse aggregate ratio of less than 1.0 and w/c ratio around 0.40 can be used with tyre rubber replacements of up to 30 % to satisfy requirements for non-structural concrete.

Porous Concrete Paving Blocks Using Coarse Aggregate

2014 ◽  
Vol 554 ◽  
pp. 111-115 ◽  
Author(s):  
A.H. Nur Hidayah ◽  
Md. Nor Hasanan ◽  
P.J. Ramadhansyah
Keyword(s):  
Laboratory Tests ◽  
Coarse Aggregate ◽  
Skid Resistance ◽  
Fine Aggregate ◽  
Particle Sizes ◽  
Test Results ◽  
Cement Ratio ◽  
Porous Concrete ◽  
Water To Cement Ratio ◽  
Resistance Tests

The objective of the study is to investigate the potential of using Porous Concrete Paving Blocks (PCPB) as a part of paving surface. Laboratory tests were conducted to compare and examine the effect of particle sizes of coarse aggregate. Two coarse aggregate sizes were selected; passing 8 mm retains 5 mm and passing 10 mm retains 8 mm. The fine aggregate was eliminated from mixes. The water to cement ratio used was 0.35. Compressive strength and skid resistance tests were performed to evaluate the properties of PCPB. The test results indicated that there was a reduction in the strength when coarse aggregate at different size was used. Scanning electron microscopy showed that voids, poor bonding and lack of adhesion at the boundaries of the aggregate with cement paste contributing to the low PCPB strength. However, both PCPB specimens provide 30 % to 40 % increase in skid resistance compared to Concrete Paving Blocks (CPB).

scholarly journals Resistencia de concreto con agregado de alta absorción y baja relación a/c

2012 ◽  
Vol 2 (1) ◽  
pp. 21-28
Author(s):  
R. G. Solís ◽  
E. Moreno ◽  
E. Arjona
Keyword(s):  
Compressive Strength ◽  
Coarse Aggregate ◽  
Construction Site ◽  
Cement Ratio ◽  
Limestone Aggregate ◽  
Concrete Mixtures ◽  
Water To Cement Ratio ◽  
Maximum Compressive Strength ◽  
Crushed Limestone ◽  
High Absorption

RESUMENLa resistencia del concreto depende de la calidad de la pasta de cemento y de las características de los agregados pétreos. La primera es controlada por la relación agua - cemento, mientras que las propiedades de los agregados generalmente no pueden ser manipuladas ya que se suele utilizar aquellos que están disponibles cerca de la construcción. En muchas regiones rocas con propiedades no deseables son utilizadas como agregado. Por lo tanto, el objetivo de este trabajo fue responder a la pregunta sobre cuál sería la máxima resistencia de diseño que se podría utilizar para concretos fabricados con un tipo específico de agregados obtenidos a partir de la trituración de roca caliza de alta absorción. Se probaron concretos con seis relaciones agua - cemento y dos tamaños de agregado grueso. Se concluyó que con los agregados estudiados es posible fabricar concretos de hasta 500 k/cm2 de f’c.Palabras clave: Absorción; agregados calizos; concreto; relación agua/cemento; resistencia.ABSTRACTConcrete strength depends on the cement paste quality and on the characteristics of the aggregates. The former is controlled by the water to cement ratio, while the properties of the aggregate, in general, cannot be manipulated as it is customary to employ the ones available near the construction site. In many regions rocks with no desirable properties are employed as aggregates. Therefore, the aim of this study was to answer the question about what would that be the maximum compressive strength attainable in concrete made with a specific type of aggregate obtained from crushed limestone of high absorption. Concrete mixtures involved six water to cement ratios and two sizes of coarse aggregate. It was concluded that with this type of aggregate it is possible to made concrete with compressive strength up to 500 k/cm2 of f’c.Key words: Absorption; compressive strength; concrete; limestone aggregate; water/cement ratio.

scholarly journals Effects of Disparate Zones of Sand on the Compressive Strength of Concrete

2021 ◽  
Vol 9 (11) ◽  
pp. 1368-1375
Author(s):  
Suhaib Bakshi
Keyword(s):  
Compressive Strength ◽  
Coarse Aggregate ◽  
Testing Machine ◽  
Concrete Compressive Strength ◽  
Research Papers ◽  
Concrete Material ◽  
Cement Ratio ◽  
Water Cement Ratio ◽  
Concrete Mix ◽  
Compressive Strength Of Concrete

Abstract: Compressive strength of concrete is the capacity of concrete to bear loads of materials or structure sans breaking or being deformed. Specimen under compression shrinks in size whilst under tension the size elongates. Compressive strength essentially gives concept about the properties of concrete. Compressive strength relies on many aspects such as water-cement ratio, strength of cement, calidad of concrete material. Specimens are tested by compression testing machine after the span of 7 or 28 days of curing. Compressive strength of the concrete is designated by the load on the area of specimen. In this research various proportions of such aggregate mixed in preparing M 30 grade and M 40 grade of Concrete mix and the effect is studied on its compressive strength . Several research papers have been assessed to analyze the compressive strength of concrete and the effect of different zones of sand on compressive strength are discussed in this paper. Keywords: Sand, Gradation, Coarse aggregate, Compressive strength

scholarly journals Valorization of Crushed Glass as a Potential Replacement for Sand in Cement Stabilized Fly Ash Bricks

2019 ◽  
Vol 15 (1) ◽  
pp. 48-57 ◽  
Author(s):  
R. Saraswathy ◽  
Jijo James ◽  
P. Kasinatha Pandian ◽  
G. Sriram ◽  
J. K. Sundar ◽  
...  
Keyword(s):  
Compressive Strength ◽  
Fly Ash ◽  
Water Absorption ◽  
Optimal Combination ◽  
Maximum Strength ◽  
Cost Comparison ◽  
Fine Aggregate ◽  
Control Specimen ◽  
The Cost ◽  
Sand Stabilized

AbstractThe present study involved the utilization of crushed glass as an auxiliary additive in the manufacture of cement stabilized fly ash (CSF) bricks. The bricks were made with 1:1 proportion of fly ash and sand stabilized with 20 % cement. Crushed glass was used as replacement for the fine aggregate in increments of 10 % up to 40 % wherein the sand was completely replaced with crushed glass. The various mix proportions were then moulded into bricks with the addition of water by hand moulding method of forming the bricks and sun dried followed by sprinkle curing over a period of 21 days. The bricks were then subjected to compressive strength, water absorption and efflorescence tests to gauge its performance. The investigation revealed that the addition of crushed glass to the brick mix resulted in an increase in strength of the bricks, however, the maximum strength achieved could not achieve the strength of the control specimen. But the strength was higher than the minimum strength recommended by Bureau of Indian Standards (BIS) for stabilized blocks as well as burnt bricks. It also reduced the water absorption marginally while no efflorescence was seen in any of the combinations. A cost comparison revealed that the optimal combination with crushed glass was able reduce the cost of the brick by 20 %.

Sign in / Sign up

Export Citation Format

Share Document