Preparation and Characterization of Mesoporous Activated Carbon Fiber

2011 ◽  
Vol 480-481 ◽  
pp. 6-10
Author(s):  
Yan Feng Yang ◽  
Xue Jun Zhang ◽  
Hai Yan Li
Keyword(s):  
Activated Carbon ◽  
Carbon Fiber ◽  
Specific Surface ◽  
Pore Size ◽  
Surface Area ◽  
Specific Surface Area ◽  
Raw Materials ◽  
Activated Carbon Fiber ◽  
Activation Process ◽  
Cobalt Salt

General purpose pitch-based carbon fiber (PCF) was pretreated with steam to develop pores on the surface of fiber. After immersed in cobalt salt solution, PCF was used as raw materials to prepare activated carbon fiber (ACF) through steam activation process. The effect of pretreatment of carbon fiber on specific surface area, mesopore volume and pore size distribution was investigated by N2 adsorption, and morphology of the resultant ACF was observed with scanning electron microscope(SEM). The results show that pretreatment of PCF enlarges specific surface area and mesopore ratio of ACF remarkably. The best ACF obtained in experiment is the one with specific surface area of 2670 m2/g and mesoporosity of 61.8%. Cobalt has evident catalysis in preparing ACF from activation of PCF, while specific surface area and pore size of ACF get smaller with cobalt salt immersion when pretreatment is too strong.

Effect of ACF Properties on the Electric Adsorption Performance of the ACF Electrode

2012 ◽  
Vol 209-211 ◽  
pp. 1990-1994 ◽  
Author(s):  
Qin Zhang ◽  
Zhao Hui Zhang ◽  
Liang Wang ◽  
Zi Long Zhang ◽  
Xing Fei Guo
Keyword(s):  
Activated Carbon ◽  
Carbon Fiber ◽  
Specific Surface ◽  
Surface Area ◽  
Specific Surface Area ◽  
Activated Carbon Fiber ◽  
Adsorption Performance ◽  
Carbon Fiber Cloth ◽  
Activated Carbon Fiber Cloth ◽  
The Relationship

The properties of four different activated carbon fiber cloth (ACF), such as specific surface area, pore volumes and pore size distribution, were evaluated. The relationship between ACF properties and its electrosorption performance was analyzed. The experimental results show that pore structure has more influence on the performance of ACF electrode than that of specific surface area for ACF material. More abundant mesopores and shallower pore channels for ACF is favorable to improve the specific capacitance and electrosorption capacity of ions.

scholarly journals Removal Characteristics of Toxic Gas on Activated Carbon Fiber Based Paper Filter

2020 ◽  
Vol 42 (6) ◽  
pp. 289-297
Author(s):  
Eunbyul Lee ◽  
Jonggu Kim ◽  
Byungtae Yoo
Keyword(s):  
Activated Carbon ◽  
Carbon Fiber ◽  
Specific Surface ◽  
Surface Area ◽  
Removal Efficiency ◽  
Specific Surface Area ◽  
Activated Carbon Fiber ◽  
Gas Removal ◽  
Paper Filter ◽  
Toxic Gas

Objectives:A paper filter was prepared by pitch based activated carbon fibers to investigate the removal efficiency of toxic gas. Also, changes in pore characteristics and mechanical properties according to the ratio of the adsorbent and the binder were observed to optimize the decrease in specific surface area and micropore, which are the unique characteristics of activated carbon fibers. In addition, it is intended to establish optimized paper filter derived activated carbon fiber manufacturing conditions through evaluation of toxic gas removal characteristics.Methods:The pore characteristics of the activated carbon fiber and prepared paper were analyzed by measuring the BET specific surface area, and SEM analysis was performed on the fine surface shape. Tensile strength and air permeability were performed according to ISO 1924-2 and ASTM D737: 04, respectively. The adsorption performance of the prepared filter was evaluated as a gas removal efficiency using a gas detection tube (GV-110S).Results and Discussion:As the content of the binder increased in the paper manufacturing process, it was confirmed that the specific surface area of ​​the prepared filter decreased by up to 39.5% compared to the activated carbon fiber. It is considered that the micropores were closed because the surface of the activated carbon fiber was coated with the excessive addition of the binder. The removal efficiency showed a removal rate of 90% of ammonia, and methyl mercaptan and hydrogen sulfide showed a removal rate of about 60%. This result might be due to the difference in the physical adsorption rate according to the vapor pressure of each material.Conclusions:An activated carbon fiber-based paper filter for removing of toxic gas was prepared. It was confirmed that the mixing ratio of the adsorbent and the binder was an important process parameter for determining moldability and adsorption performance. Finally, optimum condition was selected as weight ratio condition of 8:2.

Mesoporous Activated Carbon Filaments

1996 ◽  
Vol 454 ◽  
Author(s):  
Weiming Lu ◽  
D. D. L. Chung
Keyword(s):  
Activated Carbon ◽  
Specific Surface ◽  
Pore Size ◽  
Surface Area ◽  
Specific Surface Area ◽  
Mesoporous Activated Carbon ◽  
Carbon Filaments

ABSTRACTActivated carbon filaments of diameter ∼0.1 μm, main pore size (BJH) 55 Å, specific surface area 1310 m2/g and yield 36.2% were obtained by activating carbon filaments of diameter ∼ 0.1 urn in C02 + N2 (1:1) at 970°C for 80 min. Prior to this activation, the filaments were surface oxidized by exposure to ozone.

scholarly journals Novel Activated Carbon Nanofibers Composited with Cost-Effective Graphene-Based Materials for Enhanced Adsorption Performance toward Methane

Polymers ◽  
2020 ◽  
Vol 12 (9) ◽  
pp. 2064
Author(s):  
Faten Ermala Che Othman ◽  
Norhaniza Yusof ◽  
Noorfidza Yub Harun ◽  
Muhammad Roil Bilad ◽  
Juhana Jaafar ◽  
...  
Keyword(s):  
Graphene Oxide ◽  
Activated Carbon ◽  
Specific Surface ◽  
Pore Size ◽  
Reduced Graphene Oxide ◽  
Surface Area ◽  
Carbon Nanofibers ◽  
Specific Surface Area ◽  
Activated Carbon Nanofibers ◽  
Reduced Graphene

Various types of activated carbon nanofibers’ (ACNFs) composites have been extensively studied and reported recently due to their extraordinary properties and applications. This study reports the fabrication and assessments of ACNFs incorporated with graphene-based materials, known as gACNFs, via simple electrospinning and subsequent physical activation process. TGA analysis proved graphene-derived rice husk ashes (GRHA)/ACNFs possess twice the carbon yield and thermally stable properties compared to other samples. Raman spectra, XRD, and FTIR analyses explained the chemical structures in all resultant gACNFs samples. The SEM and EDX results revealed the average fiber diameters of the gACNFs, ranging from 250 to 400 nm, and the successful incorporation of both GRHA and reduced graphene oxide (rGO) into the ACNFs’ structures. The results revealed that ACNFs incorporated with GRHA possesses the highest specific surface area (SSA), of 384 m2/g, with high micropore volume, of 0.1580 cm3/g, which is up to 88% of the total pore volume. The GRHA/ACNF was found to be a better adsorbent for CH4 compared to pristine ACNFs and reduced graphene oxide (rGO/ACNF) as it showed sorption up to 66.40 mmol/g at 25 °C and 12 bar. The sorption capacity of the GRHA/ACNF was impressively higher than earlier reported studies on ACNFs and ACNF composites. Interestingly, the CH4 adsorption of all ACNF samples obeyed the pseudo-second-order kinetic model at low pressure (4 bar), indicating the chemisorption behaviors. However, it obeyed the pseudo-first order at higher pressures (8 and 12 bar), indicating the physisorption behaviors. These results correspond to the textural properties that describe that the high adsorption capacity of CH4 at high pressure is mainly dependent upon the specific surface area (SSA), pore size distribution, and the suitable range of pore size.

Production and characterization of lignocellulosic biomass-derived activated carbon

2010 ◽  
Vol 62 (11) ◽  
pp. 2637-2646 ◽  
Author(s):  
A. B. Namazi ◽  
C. Q. Jia ◽  
D. G. Allen
Keyword(s):  
Activated Carbon ◽  
Specific Surface ◽  
Surface Area ◽  
Lignocellulosic Biomass ◽  
Specific Surface Area ◽  
Chemical Activation ◽  
Pulp Mill ◽  
Activation Process ◽  
Activation Temperature ◽  
Biomass Ratio

The goal of this work is to establish the technical feasibility of producing activated carbon from pulp mill sludges. KOH chemical activation of four lignocellulosic biomass materials, two sludges from pulp mills, one sludge for a linerboard mill, and cow manure, were investigated experimentally, with a focus on the effects of KOH/biomass ratio (1/1, 1.5/1 and 2/1), activation temperature (400–600°C) and activation time (1 to 2 h) on the development of porosity. The activation products were characterized for their physical and chemical properties using a surface area analyzer, scanning electron microscopy and Fourier transform infrared spectroscopy. Experiments were carried out to establish the effectiveness of the lignocellulosic biomass-derived activated carbon in removing methylene blue (MB), a surrogate of large organic molecules. The results show that the activated carbon are highly porous with specific surface area greater than 500 m2/g. The yield of activated carbon was greater than the percent of fixed carbon in the dry sludge, suggesting that the activation process was able to capture a substantial amount of carbon from the organic matter in the sludge. While 400°C was too low, 600°C was high enough to sustain a substantial rate of activation for linerboard sludge. The KOH/biomass ratio, activation temperature and time all play important roles in pore development and yield control, allowing optimization of the activation process. MB adsorption followed a Langmuir isotherm for all four activated carbon, although the adsorption capacity of NK-primary sludge-derived activated carbon was considerably lower than the rest, consistent with its lower specific surface area.

Preparation and Characterization of Microporous Activated Carbon from Raw Petroleum Cokes

2015 ◽  
Vol 814 ◽  
pp. 286-291
Author(s):  
Bo Tao Wang
Keyword(s):  
Methylene Blue ◽  
Activated Carbon ◽  
Specific Surface ◽  
Pore Size Distribution ◽  
Pore Size ◽  
Surface Area ◽  
Specific Surface Area ◽  
High Specific Surface Area ◽  
Activation Time ◽  
Activation Temperature

Adopting the chemical activation method, the high specific surface area activated carbon (AC) was prepared by the solid mixing method using Daqing petroleum cokes as raw materials and KOH as activator. The influence of the ratio of KOH to carbon, activation temperature and activation time on the iodine and methylene blue adsorption properties of the AC were studied. The micro-graphitic structure of the AC was studied by X-ray diffraction (XRD). The BET specific surface area, BJH pore size distribution and pore volume of the AC were determined by N2 adsorption (at 77K). The experimental results show that the high specific surface area AC can be prepared with the ratio of KOH to carbon of 4, activation temperature of 800°C and activation time of 1h. The specific surface area was as high as 2142 m2/g with the iodine adsorption value of 288mg/g and methylene blue adsorption value of 1266mg/g. The XRD and BJH results also show that amorphous carbon was the dominating form, and the pore size distribution represents micropore structure.

scholarly journals STUDY OF SORPTION OF Ni AND Cd IONS ON NEW CARBON SORBENTS FROM KAZAKHSTAN RAW MATERIALS

2021 ◽  
Vol 57 (2) ◽  
pp. 106-113
Author(s):  
A.Zh. Yerman ◽  
◽  
A.A. Atchabarovа ◽  
K.K. Kishibaev ◽  
◽  
...  
Keyword(s):  
Activated Carbon ◽  
Specific Surface ◽  
Surface Area ◽  
Specific Surface Area ◽  
Raw Materials ◽  
Hot Water ◽  
Static Mode ◽  
Cadmium Ions ◽  
Pine Sawdust ◽  
Plant Waste

This article presents the optimal results of new sorbents for the sorption separation of nickel and cadmium ions based on waste of plant raw materials of the Republic of Kazakhstan - pine sawdust. To obtain activated carbon, pine sawdust based on plant waste was subjected to thermal treatment by carbonization methods at a temperature of 600-800 ° C and hydrothermal 220-260 ° C. Further, to increase the specific surface area, the samples after heat treatment were activated with hot water vapor at a temperature of 800-850 ° C for 1 hour. As a result of steam-gas activation, combustion of unstructured carbon and an increase in pores on the surface of activated carbon occur. In addition, the main physicochemical characteristics, sorption properties of the obtained activated carbon (specific surface area, m2 /g, fraction of pore volume, cm3 /g, average pore size, nm, sorption capacity by the amount of iodine,%) are considered. Also, the obtained sorption materials were studied in the process of sorption of nickel and cadmium ions from model solutions in a static mode. The optimal parameters of the sorption process were determined, at which the highest degree of extraction of nickel and cadmium ions is achieved: pH, phase contact time, ratio of solid and liquid phases. The recovery rate of cadmium and nickel ions in the static regime was more than 95% for cadmium and nickel. Keywords: activated carbon, sorbent, sorption, plant waste, nickel ion, cadmium ion

Preparation of Activated Carbon Fibers by Chemical Activation Method with Hydroxides

2006 ◽  
Vol 510-511 ◽  
pp. 750-753 ◽  
Author(s):  
Sook Young Moon ◽  
Myung Soo Kim ◽  
Hyun Sik Hahm ◽  
Yun Soo Lim
Keyword(s):  
Activated Carbon ◽  
Specific Surface ◽  
Surface Area ◽  
Specific Surface Area ◽  
Carbon Fibers ◽  
Chemical Activation ◽  
Lower Surface ◽  
Activation Process ◽  
Temperature Profiles ◽  
Activated Carbon Fibers

Activated carbon fibers were prepared from stabilized PAN-based fibers by chemical activation using hydroxides at different concentrations. The experimental data showed variations in specific surface area, microstructure, pore size distribution, and amounts of iodine adsorbed by the activated carbon fibers. Specific surface area of about 2244m2/g and iodine adsorption of 1202mg/g were obtained in the KOH 1.5M. However, the use of NaOH in the activation process rather than KOH and using the same time/ temperature profiles resulted in a carbon with a much lower surface area. KOH is a more developed pore structure than NaOH, which means that KOH is a better activation agent in producing ACF than NaOH.

Activated Carbon Filaments with Mainly Mesopores

1996 ◽  
Vol 431 ◽  
Author(s):  
Weiming Lu ◽  
D. D. L. Chung
Keyword(s):  
Activated Carbon ◽  
Specific Surface ◽  
Pore Size ◽  
Surface Area ◽  
Specific Surface Area ◽  
Carbon Filaments

AbstractActivated carbon filaments of diameter ∼ 0.1 μm, mean pore size (BJH) 65 Å, specific surface area 1540 m2/g and burn-off 64% (yield 36%) were obtained by activating carbon filaments of diameter ∼ 0.1 μm in CO2 + N2 (1:1) at 970°C for 100 min. Prior to this activation, the filaments were surface oxidized by exposure to ozone (0.3 vol.% in air) at 150°C for 3 min.

Sign in / Sign up

Export Citation Format

Share Document