Solid-State Reaction and Gas Sensor Properties of Porous SnO2-In2O3 Composites

2012 ◽  
Vol 512-515 ◽  
pp. 1268-1272
Author(s):  
Yu Cao ◽  
Xiao Long Zhou ◽  
Jian Chun Cao ◽  
Yuan Yuan Peng ◽  
Jing Chao Chen ◽  
...  
Keyword(s):  
Composite Materials ◽  
Solid State ◽  
Solid State Reaction ◽  
Gas Sensing ◽  
Solid State Reaction Method ◽  
Testing System ◽  
X Ray Diffraction ◽  
X Ray ◽  
Gas Sensing Properties ◽  
Sensor Properties

Mixtures of ITO and SnO2 powders were prepared by a solid-state reaction method in order to produce porous composite materials. X-ray diffraction, scanning electron microscope and gas sensing testing system have been used to analyze the microstructure and properties of it .It has been concluded that when the sintering temperature is 1573K,it has better gas-sensing properties. The pore structure and CO gas sensing property of porous SnO2-In2O3 composite materials can be improved with the increase of SnO2 contents.

Thermal enhancement of 2H11/2→4I15/2 up-conversion luminescence of Er3+ doped K2Yb(PO4)(MoO4) phosphors

2021 ◽  
Author(s):  
Hongqiang Cui ◽  
Yongze Cao ◽  
Lei Zhang ◽  
Yuhang Zhang ◽  
Siying Ran ◽  
...  
Keyword(s):  
Crystal Structure ◽  
Solid State ◽  
Solid State Reaction ◽  
Solid State Reaction Method ◽  
X Ray Diffraction ◽  
Orthorhombic Crystal ◽  
Orthorhombic Crystal Structure ◽  
Reaction Method ◽  
X Ray ◽  
Thermal Enhancement

Er3+ with different concentrations doped K2Yb(PO4)(MoO4) phosphors were prepared by a solid-state reaction method, and the layered orthorhombic crystal structure of the samples was confirmed by X-ray diffraction (XRD). Under...

Changes in Crystallite Size of Tricalcium Silicate during the Laboratory Grinding

2021 ◽  
Vol 321 ◽  
pp. 23-27
Author(s):  
Simona Ravaszová ◽  
Karel Dvořák
Keyword(s):  
Solid State ◽  
Crystallite Size ◽  
Solid State Reaction ◽  
Solid State Reaction Method ◽  
Tricalcium Silicate ◽  
Planetary Mill ◽  
X Ray Diffraction ◽  
Reaction Method ◽  
X Ray ◽  
Grinding Time

The paper is focused on one of the most important component of Portland clinker-on the tricalcium silicate. The study reported in this article is focuses on the changes in crystallite size of synthetic tricalcium silicate obtained using solid state reaction method. Crystallite size changes are monitored during the grinding in three types of laboratory mills in two different conditions. Changing in crystallite size at various grinding time up to 120 minutes are studied with the aid of X-ray diffraction and using the Scherrer equation. It has been found that the most efficient laboratory mill in terms of speed and fineness of the material was the planetary mill.

Superconducting Compound Hg0.8Sb0.2Ba2Ca2Cu3O8+δ Compared with Hg0.8Sb0.2Ba2Ca1Cu2O6+δ to Evaluate Transition Temperature

2020 ◽  
Vol 18 (11) ◽  
pp. 14-18
Author(s):  
Abbas K. Saadon ◽  
Kareem A. Jasim ◽  
Auday H. Shaban
Keyword(s):  
High Temperature ◽  
Transition Temperature ◽  
Solid State ◽  
Solid State Reaction ◽  
Hot Spot ◽  
Solid State Reaction Method ◽  
X Ray Diffraction ◽  
Reaction Method ◽  
X Ray ◽  
Superconducting Compound

The high temperature superconductor’s compounds are one of the hot spot field of science, due to their applications in industries. Hg0.8Sb0.2Ba2Ca2Cu3O8+δ and Hg0.8Sb0.2Ba2Ca1Cu2O6+δ, were manufactured using a doable-step of solid state reaction method. The samples were sintered at 800 ° C. The transition temperatures Tc are found from electrically resistively by using four probe techniques. The resistivity become zero when the transition temperature Tc(offset) have 131 and 119 K, and the onset temperature Tc(onset) have 139 K for Hg0.8Sb0.2Ba2Ca2Cu3O8+δ and 132 K for Hg0.8Sb0.2Ba2Ca1Cu2O6+δ. Analysis of X-ray diffraction showed a tetragonal structure with lattice parameters changes for all samples.

Structural, dielectric and magnetic properties of Pr-, Tb- and Dy-doped (Bi0.95RE0.05)(Fe0.95Mn0.05)O3 ceramics synthesized by solid-state reaction method

2013 ◽  
Vol 03 (04) ◽  
pp. 1350033 ◽  
Author(s):  
Radheshyam Rai ◽  
Shweta Thakur ◽  
M. A. Valente ◽  
Andrei L. Kholkin
Keyword(s):  
Magnetic Properties ◽  
Solid State ◽  
Solid State Reaction ◽  
Magnetic Measurements ◽  
Ferroelectric Properties ◽  
Solid State Reaction Method ◽  
X Ray Diffraction ◽  
Solid State Reaction Technique ◽  
X Ray ◽  
Ceramic Samples

The multiferroic ( Bi 0.95 RE 0.05)( Fe 0.95 Mn 0.05) O 3 (where RE = Pr , Tb and Dy ) has been synthesized using solid-state reaction technique. Effects of Pr , Tb and Dy substitution on the structure, electrical and ferroelectric properties of ( Bi 0.95 RE 0.05)( Fe 0.95 Mn 0.05) O 3 samples have been studied by performing X-ray diffraction, dielectric measurements and magnetic measurements. The crystal structure of the ceramic samples have a monoclinic phase. The vibrating sample magnetometer (VSM) measurement shows a significant change in the magnetic properties of Pr -, Tb - and Dy -doped ( Bi 0.95 RE 0.05)( Fe 0.95 Mn 0.05) O 3. It is seen that coercive field (Hc) and remanent magnetization (Mr) increases for Pr but decreases for Dy and Tb .

Luminescence Properties of Self-Activated M3(VO4)2 (M = Mg, Ca, Sr, and Ba) Phosphors Synthesized by Solid-State Reaction Method

2016 ◽  
Vol 16 (4) ◽  
pp. 3684-3689 ◽  
Author(s):  
Xin Min ◽  
Zhaohui Huang ◽  
Minghao Fang ◽  
Yan’gai Liu ◽  
Chao Tang ◽  
...  
Keyword(s):  
Solid State ◽  
Solid State Reaction ◽  
Single Phase ◽  
Uv Light ◽  
Solid State Reaction Method ◽  
X Ray Diffraction ◽  
Light Emitting ◽  
Reaction Method ◽  
X Ray ◽  
Yield Decrease

In this paper, M3(VO4)2 (M = Mg, Ca, Sr, and Ba) self-activated phosphors were prepared by a solid-state reaction method at 1,000 °C for 5 h. The phase formation and micrographs were analyzed by X-ray diffraction and scanning electron microscopy. The Ca3(VO4)2 phosphor does not show any emission peaks under excitation with ultraviolet (UV) light. However, the M3(VO4)2 (M = Mg, Sr, and Ba) samples are effectively excited by UV light chips ranging from 200 nm to 400 nm and exhibit broad emission bands due to the charge transfer from the oxygen 2p orbital to the vacant 3d orbital of the vanadium in the VO4. The color of these phosphors changes from yellow to light blue via blue-green with increasing ionic radius from Mg to Sr to Ba. The luminescence lifetimes and quantum yield decrease with the increasing unit cell volume and V–V distance, in the order of Mg3(VO4)2 to Sr3(VO4)2 to Ba3(VO4)2. The emission intensity decreases with the increase of temperatures, but presents no color shift. This confirms that these self-activated M3(VO4)2 phosphors can be suggested as candidates of the single-phase phosphors for light using UV light emitting diodes (LEDs).

scholarly journals Thermoluminescent properties of LaAlO3:C crystals synthesized by solid state reaction applied to UV Dosimetry

2019 ◽  
Vol 7 (2A) ◽  
Author(s):  
Neriene Alves ◽  
Wilmar Barbosa Ferraz ◽  
Luiz Oliveira Faria
Keyword(s):  
Solid State ◽  
Solid State Reaction ◽  
Solid State Reaction Method ◽  
Hydrogen Atmosphere ◽  
X Ray Diffraction ◽  
X Ray ◽  
Carbon Doped ◽  
Lanthanum Aluminate ◽  
Uv Lamp ◽  
Low Exposure

In this work, the thermoluminescent (TL) response of carbon doped lanthanum aluminate crystals grown by solid state reaction method was investigated.  Three syntheses using different combinations of Al2O3, La2O3 and 0.1 wt % of carbon atoms were conducted. The 1:1 mixture of aluminum and lanthanum oxide was mixed with 0.1wt.% carbon and annealed at 1700°C for two hours in a hydrogen atmosphere. The X-ray diffraction analysis revealed the formation of the rhombohedral LaAlO3 crystallographic phase. Ultraviolet-visible spectroscopies were obtained and F and F+ centers were identified ascribed.  Fourier transform infrared spectroscopic data show higher and lower frequencies assigned to AlO6 octahedra in LaAlO3. The UV irradiations were carried out using a commercial 8W UV lamp. Thermoluminescence measurements were performed at a Harshaw 4500 TL reader. The three syntheses were very efficient to obtain carbon doped LaAlO3 crystals with high thermoluminescent output, for low exposure rates of UVR fields.

scholarly journals Synthesis of Vanadium (III) Doped Anatase TiO2 by Solid State Reaction Method

ALCHEMY ◽  
2018 ◽  
Vol 5 (1) ◽  
pp. 26
Author(s):  
Nur Aini ◽  
Rachamawati Ningsih
Keyword(s):  
Solid State ◽  
Visible Light ◽  
Solid State Reaction ◽  
Single Phase ◽  
Diffuse Reflectance Spectroscopy ◽  
Solid State Reaction Method ◽  
X Ray Diffraction ◽  
Reaction Method ◽  
X Ray ◽  
Vanadium Doping

Anatase of Titanium dioxide (TiO<sub>2</sub>)  was doped with vanadium ions (V<sup>3+</sup>), at doping levels ranging from 0.3, 0.5 to 0.7 atomic percentage in order to increase its photocatalytic activity under visible light irradiation. Vanadium doped TiO<sub>2</sub> was synthesized by solid state reaction method. Its physicochemical properties characterized by powder X-ray diffraction (XRD) and UV-Vis diffuse reflectance spectroscopy (DRS). Doping with V(III) resulted in a single phase structure of anatase TiO<sub>2</sub> with nanosize crystal ranging from 53.06 to 59.59 nm. Vanadium doping also resulted in a red-shift of the photophysical response of TiO<sub>2</sub> that was reflected in an extended absorption in the visible light between 400 and 700 nm.

scholarly journals Study of the Structural, Magnetic and Transport properties of La3+ Doped Cu-Zn Ferrite

2020 ◽  
Vol 12 (3) ◽  
pp. 259-267
Author(s):  
K. Nahar ◽  
M. A. Hossain ◽  
P. Roy ◽  
M. N. I. Khan ◽  
S. S. Sikder
Keyword(s):  
Solid State ◽  
Diffraction Pattern ◽  
Solid State Reaction ◽  
Solid State Reaction Method ◽  
X Ray Diffraction ◽  
Conventional Solid State Reaction ◽  
Reaction Method ◽  
X Ray ◽  
Zn Ferrite ◽  
La Doped

Crystalline La doped Cu-Zn ferrite with compositions Cu0.15Zn0.85LaxFe2-xO4 [ x = 0.00, 0.02, 0.04, 0.06 and 0.08] were synthesized by using conventional solid state reaction method technique. X-ray diffraction pattern (XRD), Crystalline La doped Cu-Zn ferrite with compositions Cu0.15Zn0.85LaxFe2-xO4 [x = 0.00, 0.02, 0.04, 0.06 and 0.08] were synthesized by using conventional solid state reaction method technique. X-ray diffraction pattern (XRD), scanning electron micrographs (SEM), hysteresis loop (M-H) curves and frequency dependent resistivity were employed to inspect the effect of La3+ doping on the structure, microstructure, magnetic and transport properties of the specimens. All the specimens exhibited fcc type cubic spinel structure where the particle size were within 500-1600 nm range. Magnetically ferromagnetic phenomenon was found for all the samples where the effect of La3+ doping consequence on the variation of various parameters like saturation magnetization (Ms), coercivity (Hc) and remanent magnetization (Mr). The resistivity tuned by frequency for all the samples presented the decreasing phenomenon with the increase of applied frequency.

scholarly journals Two-dimensional SnS nanoflakes: synthesis and application to acetone and alcohol sensors

RSC Advances ◽  
2017 ◽  
Vol 7 (35) ◽  
pp. 21556-21566 ◽  
Author(s):  
M. F. Afsar ◽  
M. A. Rafiq ◽  
A. I. Y. Tok
Keyword(s):  
Solid State ◽  
Solid State Reaction ◽  
Gas Sensing ◽  
Solid State Reaction Method ◽  
Two Dimensional ◽  
Reaction Method ◽  
Sensing Properties ◽  
Gas Sensing Properties

SnS nanoflakes were synthesized using a solid state reaction method at 600 °C and their gas sensing properties were investigated.

Sign in / Sign up

Export Citation Format

Share Document