Microstructure and Properties of Hot-Pressing Sintered Tungsten Carbide Composites by Adding Cubic Boron Nitride

2015 ◽  
Vol 655 ◽  
pp. 45-48
Author(s):  
Kun Li ◽  
Hai Yan Chen ◽  
Qiu Shuang He ◽  
Li Hua Dong
Keyword(s):  
Mechanical Properties ◽  
Boron Nitride ◽  
Flexural Strength ◽  
Tungsten Carbide ◽  
Vickers Hardness ◽  
Hot Pressing ◽  
Cubic Boron Nitride ◽  
Microstructure And Mechanical Properties ◽  
Hot Pressing Sintering ◽  
Sintering Method

(0, 5, 10, 15, 20) vol% CBN-WC/Co composites were consolidated by ball milling and the following hot-pressing sintering method. WC, Co and CBN powders were used as the starting materials. The effects of the CBN content on the density, microstructure and mechanical properties of CBN-WC/Co composites were investigated. The results showed that the CBN content had remarkable influence on the microstructure and mechanical properties of CBN-WC/Co Composites. With the increasing content of CBN, the density decrease, while Vickers hardness and flexural strength increased initially to the maximum values and then decreased at CBN 10 vol%. When 10 vol% CBN-WC/Co powders were hot-pressing sintered at 1350°C and 20MPa for 90 min, an excellent Vickers hardness of 19.8GPa was achieved, combining a flexural strength of 682MPa.

Microstructure and Mechanical Properties of TiC/Ti3AlC2 In Situ Composites Prepared by Hot Pressing Method

2015 ◽  
Vol 816 ◽  
pp. 200-204 ◽  
Author(s):  
Miao Miao Ruan ◽  
Xiao Ming Feng ◽  
Tao Tao Ai ◽  
Ning Yu ◽  
Kui Hua
Keyword(s):  
Fracture Toughness ◽  
Flexural Strength ◽  
Vickers Hardness ◽  
Hot Pressing ◽  
Sintering Temperature ◽  
Powder Mixtures ◽  
Pressing Method ◽  
Hot Pressing Sintering ◽  
Sintering Method

TiC/Ti3AlC2 composites were successfully prepared by hot-pressing sintering method from the elemental powder mixtures of Ti, Al and TiC. A possible reaction mechanism was investigated by XRD. The density, Vickers hardness, flexural strength, and fracture toughness of the TiC/Ti3AlC2 composites were also measured. At 660 °C, Al melted and reacted with Ti to form TiAl3. At 900 °C, TiAl3 reacted with TiC and Ti to form Ti2AlC. At 1100 °C, Ti2AlC reacted with TiC to form Ti3AlC2. Increasing the sintering temperature, the content of Ti3AlC2 increased. The TiC/Ti3AlC2 composites had excellent performance after sintered at 1100 °C, the density, Vickers hardness, flexural strength and fracture toughness of the composite were 4.35 g/cm3, 4.72 GPa, 566 MPa and 6.18 MPa·m1/2, respectively.

Effect of Co Content on the Densification, Microstructure and Mechanical Properties of cBN-WC/Co Composites

2015 ◽  
Vol 655 ◽  
pp. 41-44
Author(s):  
Qiu Shuang He ◽  
Hai Yan Chen ◽  
Kun Li ◽  
Li Hua Dong
Keyword(s):  
Mechanical Properties ◽  
Vickers Hardness ◽  
Hot Pressing ◽  
Cemented Carbide ◽  
Sintering Process ◽  
Composite Powders ◽  
Flexure Strength ◽  
Microstructure And Mechanical Properties ◽  
Hot Pressing Sintering ◽  
Full Densification

Hot pressing sintering process for cemented carbide preparation was investigated with cBN-WC/Co composite powders with different Co content from 4wt% to 10wt% at temperatures between 1300°C and 1400°C. The results showed that the Co content had remarkable influence on the densification and mechanical properties of cBN-WC/Co composites. Near-full densification can be obtained when cBN-WC/8wt%Co powders were sintered at temperatures at 1350°C, and pressures at 20MPa, combining an excellent Vickers hardness of 17.57GPa with an acceptable flexure strength of 601.58MPa.

Influence of Hot Pressing Sintering Temperature and Time on Microstructure and Mechanical Properties of TiB2/Al2O3 Tool Materials

2012 ◽  
Vol 500 ◽  
pp. 629-633 ◽  
Author(s):  
Mei Lin Gu ◽  
Hong Jing Xu ◽  
Jian Hua Zhang ◽  
Zhi Wei
Keyword(s):  
Mechanical Properties ◽  
Fracture Toughness ◽  
Flexural Strength ◽  
Hot Pressing ◽  
Sintering Temperature ◽  
Three Point Bending ◽  
Sintering Time ◽  
Microstructure And Mechanical Properties ◽  
Hot Pressing Sintering ◽  
Increasing Temperature

In this paper, a TiB2/Al2O3composite was hot-pressed. The effect of hot pressing parameters on the TiB2/Al2O3composite microstructure and mechanical properties was investigated. The flexural strength and fracture toughness were measured by three point bending testing and direct indentation method, respectively. Experimental results show that the flexural strength decreases consistently with an increase in the sintering time, however, the fracture toughness increases consistently with an increase in the sintering time and sintering temperature. The maximum of the flexural strength is 1072 MPa at 1530 sintering temperature and 60 min sintering time. The microstructures were revealed by means of SEM. The results show that the TiB2grain size and density increases with the increasing temperature and time during hot pressing sintering, which benefits the fracture toughness and flexural strength.

Effect of TiC Content on the Microstructure and Mechanical Properties of Ti3AlC2/Al2O3 In Situ Composites Synthesized by Hot Pressing

2012 ◽  
Vol 724 ◽  
pp. 278-281 ◽  
Author(s):  
Lan Ye ◽  
Jian Feng Zhu
Keyword(s):  
Mechanical Properties ◽  
Fracture Toughness ◽  
Phase Composition ◽  
Flexural Strength ◽  
High Temperatures ◽  
Vickers Hardness ◽  
Hot Pressing ◽  
Microstructure And Mechanical Properties ◽  
Reactive Hot Pressing

The Ti3AlC2/Al2O3 in situ composites were successfully synthesized from the system of Ti-TiC-Al-TiO2 by reactive hot pressing at 1350 °C. The effect of TiC content on the phase composition, microstructure and mechanical properties were investigated in detail. The results indicate that the fabricated products possess the highest purity as the TiC contents reduce to 90 % of its theoretical content. This deviation is mainly attributed to the decomposition of Ti3AlC2 and vaporization of Al at high temperatures. The effect of TiC content on the fracture toughness, flexural strength, Vickers hardness of Ti3AlC2/Al2O3 composites was also discussed in detail.

scholarly journals Microstructure and mechanical properties of Ti3SiC2 MAX phases sintered by hot pressing

2021 ◽  
Vol 1 (4) ◽  
pp. 216-222
Author(s):  
Sheida Haji Amiri ◽  
Nasser Pourmohammadie Vafa
Keyword(s):  
Mechanical Properties ◽  
Fracture Toughness ◽  
Flexural Strength ◽  
Vickers Hardness ◽  
Hot Pressing ◽  
Sintering Temperature ◽  
Sintered Sample ◽  
Max Phases ◽  
Microstructure And Mechanical Properties ◽  
Fine Grained Structure

The Ti3SiC2 used in this project has been purchased ready-made. This study aimed to investigate the effect of sintering temperature on samples' microstructure and mechanical properties, including three-point flexural strength, Vickers hardness, and fracture toughness. Therefore, Ti3SiC2 samples were sintered under a vacuum atmosphere at a pressure of 35 MPa for 30 minutes at two temperatures of 1500 °C and 1550 °C by hot pressing. The microstructure obtained from the fracture cross-section of the samples shows that by increasing the sintering temperature to 1550 °C, the microstructure of this sample becomes larger than the sintered sample at 1500 °C. Also, increasing the sintering temperature to 1550 °C causes the decomposition of Ti3SiC2 to TiC, which can be seen in the X-ray diffraction pattern (XRD). In addition, the relative density of the sintered sample at 1550 °C is 98.08% which is higher than that of the sintered sample at 1500 °C with the result of 89%. On the other hand, the three-point flexural strength (227.5 MPa), the Vickers hardness (~9 GPa), and the fracture toughness (8.6 MPa.m1/2) of the sintered sample at 1500 °C are higher due to the fine-grained structure.

Effect of BN Short Fiber Content on Mechanical Properties of ZrB2-SiC UHTCs

2012 ◽  
Vol 512-515 ◽  
pp. 706-709 ◽  
Author(s):  
Chang Ling Zhou ◽  
Yan Yan Wang ◽  
Zhi Qiang Cheng ◽  
Chong Hai Wang ◽  
Rui Xiang Liu
Keyword(s):  
Electron Microscopy ◽  
Mechanical Properties ◽  
Fracture Toughness ◽  
Scanning Electron Microscopy ◽  
Flexural Strength ◽  
Hot Pressing ◽  
Ceramic Composites ◽  
Short Fiber ◽  
Hot Pressing Sintering ◽  
Scanning Electron

ZrB2-20%volSiC ceramic composites with different volume of BN short fiber were fabricated by the hot-pressing sintering under 2000°C. The content of BN short fiber changed from 0 to 15vol%. The density, flexural strength, fracture toughness and thermal expansions coefficient were studied. The microstructures of the samples were observed by scanning electron microscopy. The results show that the introducing of BN short fiber into the ZrB2-20%volSiC lead to a serious of change to the mechanical properties of the ceramic. When the content of the BN short fiber is 10vol%, the flexural strength and fracture toughness reach 422.1MPa and 6.15 MPa•m 1/2 respectively. And the mechanism of the increasing toughness was studied.

Microstructure and Mechanical Properties of SiC Whisker-Reinforced ZrB2 Ultra-High Temperature Ceramic

2008 ◽  
Vol 368-372 ◽  
pp. 1730-1732 ◽  
Author(s):  
Ping Hu ◽  
Xing Hong Zhang ◽  
Jie Cai Han ◽  
Song He Meng ◽  
Bao Lin Wang
Keyword(s):  
Mechanical Properties ◽  
Fracture Toughness ◽  
High Temperature ◽  
Flexural Strength ◽  
Hot Pressing ◽  
Room Temperature ◽  
Pressing Temperature ◽  
Sintering Time ◽  
Microstructure And Mechanical Properties ◽  
Ultra High Temperature

SiC whisker-reinforced ZrB2 matrix ultra-high temperature ceramic were prepared at 2000°C for 1 h under 30MPa by hot pressing and the effects of whisker on flexural strength and fracture toughness of the composites was examined. The flexural strength and fracture toughness are 510±25MPa and 4.05±0.20MPa⋅m1/2 at room temperature, respectively. Comparing with the SiC particles-reinforced ZrB2 ceramic, no significant increase in both strength and toughness was observed. The microstructure of the composite showed that the SiC whisker was destroyed because the SiC whisker degraded due to rapid atom diffusivity at high temperature. The results suggested that some related parameters such as the lower hot-pressing temperature, a short sintering time should be controlled in order to obtain SiC whiskerreinforced ZrB2 composite with high properties.

Sign in / Sign up

Export Citation Format

Share Document