Production and Characterization of RE3+:Yb2O3 Nanoparticles

2021 ◽  
Vol 1034 ◽  
pp. 117-122
Author(s):  
Fatma Unal ◽  
Kursat Kazmanli
Keyword(s):  
Crystal Structure ◽  
Profile Analysis ◽  
Average Crystallite Size ◽  
Xrd Analysis ◽  
Lattice Parameter ◽  
X Ray Diffraction ◽  
X Ray ◽  
Phase Size ◽  
Size And Morphology ◽  
Dopant Element

In this study, doped ytterbium oxide (Yb2O3) nanoparticles (NPs) with different dopant type (Eu and / or Tb) and undoped were synthesized by wet chemical method using nitrate salt as a starting source. Afterwards, they were calcined at 900 °C for 4 h. The crystal structure phase, size, and morphology of undoped and doped Yb2O3 nanoparticles (NPs) were characterized by X-ray diffraction (XRD) analysis and scanning electron microscopy (SEM). Undoped and doped NPs were exhibited cubic bixbyite-type crystal structure (Ia-3 space group). Lattice parameter changes caused by dopant element in NPs were examined using X-ray peak profile analysis. In order to investigate the occuring changes in the crystal structure, average crystallite size (CS) and lattice parameter (LP) values were computed with Williamson–Hall (W–H) and Cohen-Wagner (C–W) methods, respectively. It was observed that the crystal structure of the doped NPs expanded compared to the undoped Yb2O3 NPs, which explains the increase in the LP and CS values. The LP values of all the NPs were ranged from 10.444 Å (R2 = 94.9) to 10.453 Å (R2 = 81.8) while the CS of them were between 19 nm (R2 = 95.9) and 24 nm (R2 = 88.8). All the NPs exhibited nearly spherical and agglomerate structure and there were also few pores between the agglomerate particles in the structure. Besides, continuous agglomerate morphology formation was observed in particles containing Tb. The average nanoparticle size values were varied between 46 and 115 nm depending on the dopant element.

scholarly journals VISUALISASI STRUKTUR KRISTAL KERAMIK PEROVSKITE MENGGUNAKAN VESTA

2018 ◽  
Vol 15 (1) ◽  
pp. 46
Author(s):  
Sundami Restiana ◽  
Ari Sulistyo Rini
Keyword(s):  
Crystal Structure ◽  
Diffraction Pattern ◽  
Critical Concentration ◽  
Ceramic Materials ◽  
Lattice Parameter ◽  
Peak Position ◽  
X Ray Diffraction ◽  
X Ray ◽  
Structure Information ◽  
Software Program

Visualization of crystal structures and simulation of X-ray diffraction patterns of perovskite ceramic was successfully performed by VESTA software programs. The purpose of this research is to obtain the relation of lattice parameter, and composition to the diffraction pattern. The software program produces crystal structure information and a representative X-ray diffraction pattern for the ceramic materials. The program needs several input parameters such as the coordinates of each constituent atom, lattice parameters, and space symmetry. The obtained output of the software program are in the form of diffraction pattern graph and crystal structure data which gives the description of the profile and type (phase) of ceramic material. The results showed that the peak position and intensity of the diffraction pattern are influenced by the arrangement of  the atoms within the unit cell. The addition of impurity atoms such as Sr on the Ba side in BaTiO3 causes the BaTiO3 structure changes from Orthorombic (a≠b≠c) to Tetragonal (a=b≠c) structure. Based on the simulation, it can be predicted that the critical concentration of the change of structure occur at Sr concentration about 0.4.

scholarly journals X-ray diffraction analysis of MTA-Plus, MTA-Angelus and DiaRoot BioAggregate

2014 ◽  
Vol 08 (02) ◽  
pp. 211-215 ◽  
Author(s):  
Yeliz Guven ◽  
Elif Bahar Tuna ◽  
Muzaffer Emin Dincol ◽  
Oya Aktoren
Keyword(s):  
Crystal Structure ◽  
Tantalum Oxide ◽  
Xrd Analysis ◽  
Tricalcium Silicate ◽  
Dicalcium Silicate ◽  
Glass Slide ◽  
Phase Identification ◽  
X Ray Diffraction ◽  
X Ray ◽  
Tricalcium Aluminate

ABSTRACT Objective: The purpose of this study was to investigate and compare the crystalline structures of recently released MTA Plus (MTA-P), MTA Angelus (MTA-A), DiaRoot BioAggregate (BA) by X-ray diffraction (XRD) analysis. Materials and Methods: Phase analysis was carried out on powder and set forms of tested materials. The powder specimens placed into sample holders that were packed with a glass slide and the set samples prepared according to the manufacturer's instructions were placed into molds. The samples after being set for three days at 37°C and 100% humidity in an incubator were mounted onto the XRD machine and phase identification was accomplished using a search-match software program. Results: XRD findings indicated that major constituents of MTA-P were bismuth oxide, portlandite, dicalcium silicate and tricalcium silicate. The crystal structure of MTA-A were similar to those of MTA-P except for the absence of portlandite. Additionally, MTA-A had tricalcium aluminate differing from MTA-P. BA mainly differed from MTA-P and MTA-A by the radiopacifier (tantalum oxide-TO) in its composition. Conclusions: The majority of constituents of the tested materials have shown similarity except for the presence of tricalcium aluminate in MTA-A and the inclusion of TO in BA. In addition, set MTA-P showed a strong peak of portlandite.

The Effect of Water Content on the Formation of TiO2 Nanotubes in Ethylene Glycol

2010 ◽  
Vol 173 ◽  
pp. 102-105 ◽  
Author(s):  
Khairul Arifah Saharudin ◽  
Srimala Sreekantan
Keyword(s):  
Crystal Structure ◽  
Aspect Ratio ◽  
Ethylene Glycol ◽  
Water Content ◽  
Anatase Phase ◽  
Xrd Analysis ◽  
X Ray Diffraction ◽  
X Ray ◽  
Degradation Of Methyl Orange ◽  
Scanning Electron

In this paper, anodization of Ti foil was carried out in ethylene glycol (EG) containing 5 wt% NH4F solution and 0 to 1.5 wt% of water at 50 V for 60 min. The pH of the bath was kept constant at ~pH7. The crystal structure was studied by X-Ray Diffraction (XRD) analysis, and the morphology was observed via field emission scanning electron microscopy (FESEM). TiO2 nanotube with aspect ratio of 100 was obtained in EG containing less than 1wt % water. The nanotubes wall was very smooth. Increasing the water content > 1wt % results in short nanotubes of approximately 6.2μm with aspect ratio of 62. As anodized, nanotubes were amorphous and annealed at 400 °C promote 100 % anatase phase. Photocatalytic activity of the nanotubes produced at different water content was also evaluated by the degradation of methyl orange and the detail of the observation was discussed thoroughly in this paper.

scholarly journals Synthesis, Characterization, and Thermal Decomposition of Pure and Dysprosium Doped Yttrium Phosphate System

2013 ◽  
Vol 2013 ◽  
pp. 1-8 ◽  
Author(s):  
K. K. Bamzai ◽  
Nidhi Kachroo ◽  
Vishal Singh ◽  
Seema Verma
Keyword(s):  
Thermogravimetric Analysis ◽  
Ammonium Hydroxide ◽  
Xrd Analysis ◽  
Lattice Parameter ◽  
Energy Dispersive ◽  
Water Molecules ◽  
X Ray Diffraction ◽  
Scanning Calorimetry ◽  
Structural Investigations ◽  
X Ray

Yttrium phosphate and dysprosium doped yttrium phosphate were synthesized from aqueous solutions using rare earth chloride, phosphoric acid, and traces of ammonium hydroxide. The synthesized material was then characterized for their structural investigations using powder X-ray diffraction (XRD) analysis and scanning electron microscopy (SEM) supplemented with energy dispersive X-ray analysis (EDAX). The spectroscopic investigations were carried out using Fourier transform infrared (FTIR) spectroscopy. The thermal stability was studied using differential thermogravimetric analysis (DTA), thermogravimetric analysis (TGA), and differential scanning calorimetry (DSC) techniques. X-ray diffraction analysis reveals that both yttrium phosphate and dysprosium doped yttrium phosphate belong to tetragonal system with lattice parameter  Å,  Å and  Å,  Å, respectively. The stoichiometry of the grown composition was established by energy dispersive X-ray analysis. The EDAX analysis suggests the presence of water molecules. The presence of water molecules along with orthophosphate group and metallic ion group was confirmed by FTIR analysis. Thermogravimetric analysis suggests that decomposition in case of yttrium phosphate takes place in three different stages and the final product stabilizes after 706°C, whereas in case of dysprosium doped yttrium phosphate the decomposition occurs in two different stages, and the final product stabilizes after 519°C.

Studied on Structural Characterization of Lanthanum Doped Barium Titanium Ceramics

2015 ◽  
Vol 819 ◽  
pp. 198-203
Author(s):  
Nur Farahin Abdul Hamid ◽  
Rozana Aina Maulat Osman ◽  
Mohd Sobri Idris ◽  
Tze Qing Tan
Keyword(s):  
Crystal Structure ◽  
Lattice Parameter ◽  
Phase Changes ◽  
X Ray Diffraction ◽  
X Ray ◽  
Tetragonal Crystal ◽  
Tetragonal Crystal Structure ◽  
La Doped ◽  
Conventional Solid State Synthesis

La-doped barium titanate (BaTiO3) was prepared using conventional solid state synthesis route. All peaks for sample x=0 are approaching the phase pure of BaTiO3 structure with tetragonal crystal structure (P4mm). Sintering of pressed powder are performed at 1300oC, 1400oC and 1450oC for overnight for pure BaTiO3 and 1350oC for 3 days for BaTiO3 doped lanthanum with intermittent grinding. Phase transition was studied by different x composition. The changes in the crystal structure of the composition x=0.1 and 0.2 were detected by using X-ray diffraction (XRD). The phase changes between tetragonal-cubic and cubic-tetragonal depending on the temperature. Rietveld Refinement analysis is carried out to determine the lattice parameter and unit cell for BaTiO3.

X-Ray Diffraction Profile Analysis for the Determination of the Crystal Structure of BaTiO3

1980 ◽  
Vol 19 (9) ◽  
pp. 1757-1762 ◽  
Author(s):  
Masahiro Tanaka ◽  
Hideshi Fujishita ◽  
Yōichi Shiozaki ◽  
Etsuro Sawaguchi
Keyword(s):  
Crystal Structure ◽  
Profile Analysis ◽  
X Ray Diffraction ◽  
Diffraction Profile ◽  
X Ray

scholarly journals Microstructure, Stress and Texture in Sputter Deposited TiN Thin Films: Effect of Substrate Bias

2014 ◽  
Vol 996 ◽  
pp. 855-859 ◽  
Author(s):  
Jay Chakraborty ◽  
Tias Maity ◽  
Kishor Kumar ◽  
S. Mukherjee
Keyword(s):  
Thin Films ◽  
Film Growth ◽  
Profile Analysis ◽  
Lattice Parameter ◽  
Line Profile Analysis ◽  
Substrate Bias ◽  
X Ray Diffraction ◽  
Strain Anisotropy ◽  
X Ray ◽  
Tin Thin Films

Titanium nitride thin films deposited by reactive dc magnetron sputtering under various substrate bias voltages have been investigated by X-ray diffraction. TiN thin films exhibits lattice parameter anisotropy for all bias voltages. Preferential entrapment of argon atoms in TiN lattice has been identified as the major cause of lattice parameter anisotropy. Bombardment of argon ions during film growth has produced stacking faults on {111} planes of TiN crystal. Stacking fault probability increases with increasing substrate bias voltages. X-ray diffraction line profile analysis indicates strain anisotropy in TiN thin films. Diffraction stress analysis by d-sin2ψ method reveals pronounced curvature in the plot of inter-planar spacing (d) (or corresponding lattice parameter (a)) versus sin2ψ. Direction dependent elastic grain interaction has been considered as possible source of the observed anisotropic line broadening.

X-ray structure determination of the rare earth oxides (Er1−uGdu)2O3applying the Rietveld method

2002 ◽  
Vol 35 (5) ◽  
pp. 577-580 ◽  
Author(s):  
Zein Heiba ◽  
Hasan Okuyucu ◽  
Y. S. Hascicek
Keyword(s):  
Rare Earth ◽  
Rietveld Method ◽  
Sol Gel ◽  
Average Crystallite Size ◽  
Lattice Parameter ◽  
X Ray Diffraction ◽  
X Ray ◽  
Gel Technique ◽  
Average Size

Nanosized polycrystalline samples of (Er1−uGdu)2O3(0 ≤u≤ 1.0) were synthesized by a sol–gel technique. X-ray diffraction data were collected and the crystal structures were refined by the Rietveld method. All samples are found to have the same crystal system and formed solid solutions over the whole range ofu. The Er3+and Gd3+ions were randomly distributed over two cationic sites, 8band 24d, in the space groupIa\bar{3} (206) in all refined structures. The lattice parameter was found to vary non-linearly with the composition (u). The average microstrain and average crystallite size have been calculated from the Williamson–Hall plots for each sample. The average size ranges from 50 to 70 nm, and the microstrain from 0.4 to 1.7%.

Molecular Packing Structure of Mesogenic Octa-Hexyl Substituted Phthalocyanine Thin Film by X-ray Diffraction Analysis

2016 ◽  
Vol 16 (4) ◽  
pp. 3318-3321 ◽  
Author(s):  
Masashi Ohmori ◽  
Takuya Higashi ◽  
Akihiko Fujii ◽  
Masanori Ozaki
Keyword(s):  
Thin Film ◽  
Crystal Structure ◽  
Liquid Crystalline ◽  
Xrd Analysis ◽  
Molecular Packing ◽  
Normal Vector ◽  
Organic Thin Film ◽  
X Ray Diffraction ◽  
X Ray ◽  
Packing Structure

The molecular packing structure in a thin film of the liquid crystalline phthalocyanine, 1,4,8,11,15,18,22,25-octahexylphthalocyanine (C6PcH2), which is a promising small-molecular material for solution-processable organic thin-film solar cells, has been investigated by X-ray diffraction (XRD) measurement. The crystal structure of C6PcH2 in the spin-coated film was determined to be a centered rectangular structure (a= 36.4Å, b 20.3 Å). The tilt angle of the phthalocyanine core normal vector was 34–39° from the column axis, and the shortest intermolecular distance was 3.9–4.0 Å. The crystal structure determined by XRD analysis was ascertained to be consistent with that calculated by Fourier analysis.

scholarly journals Formation of NanoscaleMg(x)Fe(1-x)O  (x=0.1,0.2,0.4)Structure by Solution Combustion: Effect of Fuel to Oxidizer Ratio

2012 ◽  
Vol 2012 ◽  
pp. 1-8 ◽  
Author(s):  
Mohsen Ahmadipour ◽  
K. Venkateswara Rao ◽  
V. Rajendar
Keyword(s):  
Particle Size ◽  
Electron Microscope ◽  
Crystallite Size ◽  
Average Crystallite Size ◽  
Combustion Method ◽  
X Ray Diffraction ◽  
Solution Combustion ◽  
X Ray ◽  
Particle Size And Morphology ◽  
Size And Morphology

Mg(x)Fe(1-x)O(magnesiowustite) nanopowder samples synthesized by solution-combustion method and fuel to oxidizer ratio (Ψ=1,1.25) are used as a control parameter to investigate how particle size and morphology vary withΨ. The method is inexpensive and efficient for synthesis of oxide nanoparticles. The average crystallite size ofMg(x)Fe(1-x)Onanoparticles was estimated from the full-width-half maximum of the X-ray diffraction peaks of powders using Debye-Scherrer’s formula; the average crystallite size varies from 16 nm to 51 nm. From X-ray diffraction analysis, it was observed thatMg(x)Fe(1-x)Onanoparticles have cubic structure. The particle size measured by particle size analyzer ranges from 37.7 nm to 73 nm which is in the order of XRD results. Thermal analysis was done by thermal gravimetric-differential thermal analyzer. The particle size and morphology of the synthesized powder were examined by transmission electron microscope and scanning electron microscope. The crystal size and particle size were compared with some of the most recently published research works by XRD and TEM. FTIR conforms formation of theMg(x)Fe(1-x)O.

Sign in / Sign up

Export Citation Format

Share Document