Bioactivity of Plasma-Sprayed TiO2 Coating in Simulated Body Fluid by Hydrofluoric Acid Treatment

2006 ◽  
Vol 510-511 ◽  
pp. 13-16
Author(s):  
Xiao Bing Zhao ◽  
Xuan Yong Liu ◽  
Chuan Xian Ding
Keyword(s):  
Titanium Alloy ◽  
Simulated Body Fluid ◽  
Hydrofluoric Acid ◽  
Body Fluid ◽  
Acid Treatment ◽  
Atmospheric Plasma ◽  
X Ray ◽  
Tio2 Coatings ◽  
Plasma Sprayed

TiO2 coatings on titanium alloy substrates were prepared by atmospheric plasma spraying using commercial nano-powders. Then, as-sprayed coatings were treated using 10% hydrofluoric acid (HF) at room temperature for 30 seconds. As-sprayed and HF-treated titania coatings were soaked in simulated body fluid to investigate the formation of apatite on their surface. Field-emission scanning electron microscopy was used to observe the surface morphologies, and the phase composition of the as-sprayed coating and apatite were analyzed by X-ray diffraction and energy-dispersive X-ray spectrometry. As-sprayed titania coating is composed of rutile, anatase, and a small quantity of Ti3O5. It exhibited excellent adhesion between the TiO2 coatings and titanium alloy substrates, and the bonding strength was about 38 MPa. After in vitro experiment, a new substance containing calcium and phosphate was formed on the surface of HF-treated TiO2 coatings after being soaked in SBF, while the new substance was not formed on the surface of as-sprayed TiO2 coatings. The results indicated that the bioactivity can be induced to the surface of plasma sprayed TiO2 coatings by hydrofluoric acid treatment.

Apatite Formation on Surface of Plasma-Sprayed TiO2 Coating by Sulfuric Acid Treatment

2007 ◽  
Vol 544-545 ◽  
pp. 653-656
Author(s):  
Xiao Bing Zhao ◽  
Xuan Yong Liu ◽  
You Tao Xie ◽  
Zhi Gang Chen ◽  
Chuan Xian Ding
Keyword(s):  
Simulated Body Fluid ◽  
Body Fluid ◽  
Atmospheric Plasma ◽  
Apatite Formation ◽  
Sulfuric Acid Treatment ◽  
Before And After ◽  
Tio2 Coatings ◽  
Plasma Sprayed ◽  
Surface Morphologies ◽  
Soaking Test

TiO2 coatings on titanium alloy substrates were prepared by atmospheric plasma spraying using commercial nano-powders and followed by H2SO4 treatment. The bioactivity of coatings was evaluated by the simulated body fluid soaking test. Scanning electron microscopy and energy-dispersive X-ray spectrometry were used to characterize the surface morphologies and phase composition of the coating before and after soaking in simulated body fluid. The results obtained indicate that H2SO4-treated TiO2 coating can induce a bone-like apatite formation on its surface, however, no apatite appears on the surface of as-sprayed TiO2 coatings. The acid concentration and treated time affected the bioactivities of TiO2 coatings.

scholarly journals Preparation and Degradation Characteristics of MAO/APS Composite Bio-Coating in Simulated Body Fluid

Coatings ◽  
2021 ◽  
Vol 11 (6) ◽  
pp. 667
Author(s):  
Zexin Wang ◽  
Fei Ye ◽  
Liangyu Chen ◽  
Weigang Lv ◽  
Zhengyi Zhang ◽  
...  
Keyword(s):  
Simulated Body Fluid ◽  
Composite Coating ◽  
Body Fluid ◽  
Composite Coatings ◽  
Degradation Process ◽  
Ceramic Coatings ◽  
Immersion Test ◽  
Substrate Material ◽  
Atmospheric Plasma

In this work, ZK60 magnesium alloy was employed as a substrate material to produce ceramic coatings, containing Ca and P, by micro-arc oxidation (MAO). Atmospheric plasma spraying (APS) was used to prepare the hydroxyapatite layer (HA) on the MAO coating to obtain a composite coating for better biological activity. The coatings were examined by various means including an X-ray diffractometer, a scanning electron microscope and an energy spectrometer. Meanwhile, an electrochemical examination, immersion test and tensile test were used to evaluate the in vitro performance of the composite coatings. The results showed that the composite coating has a better corrosion resistance. In addition, this work proposed a degradation model of the composite coating in the simulated body fluid immersion test. This model explains the degradation process of the MAO/APS coating in SBF.

Bioactivity of Silver Doped Hydroxyapatite Scaffolds in Simulated Body Fluids

2014 ◽  
Vol 604 ◽  
pp. 175-179 ◽  
Author(s):  
Lasma Poca ◽  
Arita Dubnika ◽  
Dagnija Loca ◽  
Liga Berzina-Cimdina
Keyword(s):  
Simulated Body Fluid ◽  
Incubation Period ◽  
Powder Diffraction ◽  
Body Fluid ◽  
Body Fluids ◽  
Apatite Layer ◽  
X Ray ◽  
Simulated Body Fluids ◽  
Two Phases

In the present study, thein vitrobioactivity of silver-doped hydroxyapatite (HAp/Ag) scaffolds was investigated. HAp/Ag was prepared using two different modified wet precipitation methods. The X-ray powder diffraction (XRD) results showed, that sintered HAp/Ag samples prepared using method (I) contain two phases HAp and Ag, but samples prepared by method (II) contain three different phases - HAp, Ag and AgO. After 2 month incubation period in simulated body fluid (SBF), surface of HAp/Ag scaffolds was coated with bone-like apatite. Thickness of bone-like apatite layer increased from 2 μm up to 32 μm, increasing the incubation period.

In Vitro Study of Microplasma Sprayed Hydroxyapatite Coatings in Simulated Body Fluid

2009 ◽  
Vol 79-82 ◽  
pp. 815-818 ◽  
Author(s):  
Qiu Ying Zhao ◽  
Ding Yong He ◽  
Xiao Yan Li ◽  
Jian Min Jiang
Keyword(s):  
Simulated Body Fluid ◽  
Body Fluid ◽  
Carbonate Apatite ◽  
In Vitro Test ◽  
X Ray Diffraction ◽  
X Ray ◽  
Amorphous Phases ◽  
Hydroxyapatite Coatings ◽  
Vitro Test

Hydroxyapatite (HA) coatings were deposited onto Ti6Al4V substrate by microplasma spraying (MPS) in the current research. The morphology, phase compositions, and percentage of crystallinity of the coatings were characterized by means of scanning electron microscopy (SEM) and X-ray diffraction. An in vitro evaluation by soaking the coatings in simulated body fluid (SBF) for up to 14 days was conducted aiming at the evaluation of their bioactivity. Results from the present investigation suggest that microplasma sprayed HA coatings exhibited certain roughness, pores, and microcracks. Thermal decomposition existed in the coatings where HA, α-TCP，β-TCP, amorphous phases, and CaO-exclusive impurities were observed. The in vitro test indicated that HA coatings deposited by MPS possessed better bioactivity and stability. A layer of carbonate-apatite covered most of the coating surface, which did not exhibit significant spalling after incubation in SBF.

scholarly journals The Atomic-Scale Interaction of Bioactive Glasses with Simulated Body Fluid

2005 ◽  
Vol 480-481 ◽  
pp. 21-26 ◽  
Author(s):  
L.J. Skipper ◽  
F.E. Sowrey ◽  
D.M. Pickup ◽  
R.J. Newport ◽  
K.O. Drake ◽  
...  
Keyword(s):  
Simulated Body Fluid ◽  
Body Fluid ◽  
Sol Gel ◽  
Atomic Scale ◽  
X Ray Diffraction ◽  
Bioactive Glasses ◽  
Edge Structure ◽  
X Ray ◽  
X Ray Absorption

The formation of a carbonate-containing hydroxyapatite, HCAp, layer on bioactive calcium silicate sol-gel glass of the formula (CaO)0.3(SiO2)0.7 has been studied in-vitro in Simulated Body Fluid (SBF). Extended X-ray Absorption Fine Structure (EXAFS), X-ray Absorption Near Edge Structure (XANES), X-ray diffraction (XRD), and solid state nuclear magnetic resonance (NMR) measurements have been performed with results showing the formation of a significantly amorphous HCAp layer after less than 5 hours in solution.

Studies on Development, Bioactivity and Corrosion Behaviour of Nanostructured Titania/Hydroxyapatite Composite Layer on Cp Ti

2011 ◽  
Vol 471-472 ◽  
pp. 325-330 ◽  
Author(s):  
K. Venkateswarlu ◽  
N. Rameshbabu ◽  
Arumugam Chandra Bose ◽  
V. Muthupandi ◽  
S. Subramanian
Keyword(s):  
Corrosion Resistance ◽  
Simulated Body Fluid ◽  
Body Fluid ◽  
Composite Layer ◽  
In Vitro Bioactivity ◽  
X Ray ◽  
Composite Layers ◽  
Cp Ti ◽  
Nanostructured Titania

Nanostructured titania/hydroxyapatite (HA) composite layer was developed on commercially pure titanium (Cp Ti) implant material by plasma electrolytic processing (PEP) technique in order to improve its bioactivity and corrosion resistance under physiological conditions. The phases present in the developed composite layer were studied by X-ray diffraction (XRD) technique. The surface morphology and thickness of the composite layers were observed by scanning electron microscopy (SEM). The corrosion characteristics of the developed layer were studied by potentiodynamic polarization scan under simulated body fluid (7.4 pH Hanks solution) and simulated osteoclast (4.5 pH) conditions. The in-vitro bioactivity of the composite layers was studied by using Kokubu’s simulated body fluid (SBF) solution. The X-ray diffractograms reveal the presence of anatase TiO2 and HA phases in the developed layer. The SEM results confirm the pore-free morphology of the implant material surface and the thickness of the developed composite layer was observed to be 110 ± 5 µm for 12 min of PEP. The potentiodynamic polarization study shows an improved corrosion resistance and the in-vitro bioactivity test results indicate enhanced apatite forming ability of PEP treated Cp Ti surfaces compared to that of the untreated Cp Ti, under simulated body fluid conditions.

scholarly journals Improved bioactivity of GUMMETAL®, Ti59Nb36Ta2Zr3O0.3, via formation of nanostructured surfaces

2018 ◽  
Vol 9 ◽  
pp. 204173141877417 ◽  
Author(s):  
Shiva Kamini Divakarla ◽  
Seiji Yamaguchi ◽  
Tadashi Kokubo ◽  
Dong-Wook Han ◽  
Jae Ho Lee ◽  
...  
Keyword(s):  
Simulated Body Fluid ◽  
Body Fluid ◽  
Cell Attachment ◽  
Cell Number ◽  
Calcium Titanate ◽  
Apatite Formation ◽  
X Ray ◽  
Nanostructured Surfaces ◽  
Implant Integration

The leading reason for implant revision surgery globally is lack of implant integration with surrounding bone. A new titanium alloy GUMMETAL® (Ti59Nb36Ta2Zr3O0.3) is currently used in biomedical devices and has a Young’s modulus that is better matched to bone. The surface was subject to NaOH, CaCl2, heat and water treatment (BioGum) after which the surfaces were evaluated using atomic force microscope, scanning electron microscope, X-ray diffractometer and elemental analysis using energy dispersive X-ray. To demonstrate enhanced bone bonding ability and cytocompatibility, apatite formation in simulated body fluid and in vitro stem cell attachment, proliferation and cytoskeleton organisation were examined. The formation of a ~200 nm nanoscale needle-like calcium titanate network on the surface following treatment was revealed and upon soaking in simulated body fluid, the formation of a ~5 µm layer of apatite. Metabolic activity of rat bone marrow stem cells on BioGum was increased in comparison to control and the cell number appeared greater, with more elongated morphology as early as 2 h post-seeding. This positions the modification as a simple and potentially universal technology for the improvement of implant integration.

Microstructure and in vitro bioactivity of laser-cladded bioceramic coating on titanium alloy in a simulated body fluid

2010 ◽  
Vol 489 (1) ◽  
pp. 211-214 ◽  
Author(s):  
Min Zheng ◽  
Ding Fan ◽  
Xiu-kun Li ◽  
Jian-bin Zhang ◽  
Qi-bin Liu
Keyword(s):  
Titanium Alloy ◽  
Simulated Body Fluid ◽  
Body Fluid ◽  
In Vitro Bioactivity

Micro-Topography and Reactivity of Implant Surfaces: An In Vitro Study in Simulated Body Fluid (SBF)

2015 ◽  
Vol 21 (1) ◽  
pp. 190-203 ◽  
Author(s):  
M.G. Gandolfi ◽  
P. Taddei ◽  
F. Siboni ◽  
V. Perrotti ◽  
G. Iezzi ◽  
...  
Keyword(s):  
Simulated Body Fluid ◽  
Body Fluid ◽  
Calcium Phosphates ◽  
Raman Band ◽  
Biologically Active ◽  
Textured Surface ◽  
X Ray ◽  
Micro Topography ◽  
Element Mapping

AbstractThe creation of micro-textured dental implant surfaces possessing a stimulating activity represents a challenge in implant dentistry; particularly, the formation of a thin, biologically active, calcium-phosphate layer on their surface could help to strengthen the bond to the surrounding bone. The aim of the present study was to characterize in terms of macrostructure, micro-topography and reactivity in simulated body fluid (SBF), the surface of titanium (Ti) implants blasted with TiO2 particles, acid etched with hydrofluoric acid, and activated with Ca and Mg-containing nanoparticles. Sandblasted and acid-etched implants were analyzed by ESEM-EDX (environmental scanning electron microscope with energy dispersive X-ray system) to study the micromorphology of the surface and to perform elemental X-ray microanalysis (microchemical analyses) and element mapping. ESEM-EDX analyses were performed at time 0 and after a 28-day soaking period in SBF Hank’s balanced salt solution (HBSS) following ISO 23317 (implants for surgery—in vitro evaluation for apatite-forming ability of implant materials). Microchemical analyses (weight % and atomic %) and element mapping were carried out to evaluate the relative element content, element distribution, and calcium/phosphorus (Ca/P) atomic ratio. Raman spectroscopy was used to assess the possible presence of impurities due to manufacturing and to investigate the phases formed upon HBSS soaking. Micro-morphological analyses showed a micro-textured, highly rough surface with microgrooves. Microchemical analyses showed compositional differences among the apical, middle, and distal thirds. The micro-Raman analyses of the as-received implant showed the presence of amorphous Ti oxide and traces of anatase, calcite, and a carbonaceous material derived from the decomposition of an organic component of lipidic nature (presumably used as lubricant). A uniform layer of Ca-poor calcium phosphates (CaPs) (Ca/P ratio <1.47) was observed after soaking in HBSS; the detection of the 961 cm−1 Raman band confirms this finding. These implants showed a micro-textured surface supporting the formation of CaPs when immersed in SBF. These properties may likely favor bone anchorage and healing by stimulation of mineralizing cells.

Sign in / Sign up

Export Citation Format

Share Document