scholarly journals New Creep Deformation Concept Based on Creep under Lower Stresses

2010 ◽  
Vol 638-642 ◽  
pp. 2297-2302
Author(s):  
Takashi Matsuo
Keyword(s):  
Steady State ◽  
Creep Rate ◽  
Slip System ◽  
Single Crystals ◽  
Creep Deformation ◽  
Single Phase ◽  
Rupture Life ◽  
Stage Iii ◽  
Transient Stage ◽  
Primary Slip System

Through the analysis of many creep rate-time or creep rate-strain curves of -single phase Ni-20mass% Cr alloy single crystals with various stress axes, it was clarified that the creep deformation manners at lower stresses are drastically different to those at higher stresses. These creep features at lower stresses are summarized into three ones as follows. (i) The fully extended transient stage occupies the considerable ratio of rupture life. (ii) The steady state stage disappears, because the transient stage directly connected with the accelerating stage. (iii) The origin of the onset of accelerating stage is regarded as the formation of the dynamic recrystallized grain. These difference in creep deformation manner were caused by the predominant operation of the primary slip system and then the homogeneous evolution of dislocation substructures.

Role of Transient Creep in γ-Single Phase Ni-20Mass%Cr Alloy

2007 ◽  
Vol 539-543 ◽  
pp. 3030-3035
Author(s):  
Takashi Matsuo
Keyword(s):  
Creep Rate ◽  
Slip System ◽  
Single Crystal ◽  
Single Crystals ◽  
Slip Plane ◽  
Single Phase ◽  
Stage I ◽  
Stage Ii ◽  
Stress Axis ◽  
Transient Stage

Through the analysis of many creep rate-strain curves of γ-single phase Ni-20mass%Cr alloy single crystals with various stress axes, it has been elucidated that the ratio of transient stage to rupture life becomes larger with decreasing the stress. And the transient stage consists of Stage I and Stage II. In Stage I, the creep rate just after loading remains constant, and in Stage II, a steep decrease in creep rate continues. It is noticeable that there is a marked difference in transient stage among single crystals with different stress axes. The aim of this study is to elucidate the mechanisms leading to the different transient stages as the function of stress axes. The deformation during transient stage in the single crystals except for the single crystals with the stress axes of the [001] and [1,–11] poles in the standard stereographic triangle, proceeds using the primary slip plane. And they are divided into two groups of the single crystals with the angle between stress axis and primary slip plane, θ, less than 45° and the single crystals with θ more than 45°. The deformations of Stage I and Stage II in these single crystals proceed using the slip system of (111)<1,–01> and the slip system of (111)<1,–10>, and in Stage I, the former slip system acts mainly except for that of single crystals with stress axis of [011]. While, in the single crystal with stress axis of [011], two slip systems above described operate at the beginning of Stage I, and the stress axis moves along [011]-[1,–11] line. And this moving gives slight increase in the Schmid factor, therefore, in Stage I slight increase in creep rate was confirmed. The {111} pole figure of the single crystal with stress axis of [1,–11] whose deformation proceeds using the plural slip planes are obtained by SEM-EBSD method. It becomes clear that the smallest strains of Stage I and Stage II derived from the increase in the torsion with creep deformation.

Change in Stress Axis with Creep Deformation in γ-Single Phase Ni-20mass%Cr Single Crystal within Standard Stereographic Triangle

2006 ◽  
Vol 15-17 ◽  
pp. 864-869 ◽  
Author(s):  
Kentaro Yuge ◽  
Yoshihiro Terada ◽  
Takashi Matsuo
Keyword(s):  
Creep Rate ◽  
Slip System ◽  
Single Crystals ◽  
Slip Plane ◽  
Creep Deformation ◽  
Single Phase ◽  
Stage I ◽  
Stress Axis ◽  
Stereographic Triangle ◽  
Primary Slip Plane

The creep deformations of γ-single phase Ni-20mass%Cr single crystals with stress axes within standard stereographic triangle and at the three pole positions have been investigated. The most of the creep life is occupied by the transient stage, which consists of Stage I and Stage II. In Stage I, the creep rate just after loading remains constant. In Stage II, the creep rate decreases continuously. Except for the single crystals with stress axes of [001] and [1,–11] poles, the single crystals make the creep deformation using the primary slip plane of (111). As a result, the cross section of the specimens turns from circular to elliptical in shape. However, there are marked difference in deformation manner among single crystals with the stress axes within standard stereographic triangle. The single crystals whose angle between stress axis and primary slip plane of (111), θ. is more than 45° shows the heterogeneous deformation during creep. While, the homogeneous deformation will be expected in the single crystals with θ less than 45°. In this study, by using the four single crystals with θ less than 45°, the change in the stress axis with the creep deformation at 1173K-29.4MPa, is investigated and the deformation manner due to the primary slip plane of (111) is estimated by conducting the creep interrupting tests. In the two single crystals with stress axes in the standard stereographic triangle where the moving range of θ is narrow, comparing to the others, the spot of the stress axis in the inverse pole figure moves for <1,– 01> direction by using (111)<1,–01> slip system, and after arriving at the [001]-[1,–11] line, the spot turns to its direction for [1,–11] pole using (111)<1,–10> slip system. While, in the other two single crystals whose stress axes located in the area with wider moving range of θ, the spot of stress axis only move for <1,–01> direction. And, the widely spread spot of the stress axis is confirmed after subjecting the small strain.

Change in Creep Deformation of PST Crystals with Different Stress Axes

2006 ◽  
Vol 980 ◽  
Author(s):  
Xiaohua Min ◽  
Eisaku Sakurada ◽  
Masao Takeyama ◽  
Takashi Matsuo
Keyword(s):  
Creep Rate ◽  
Slip System ◽  
Initial Stress ◽  
Creep Deformation ◽  
Strain Curve ◽  
Stage I ◽  
Stress Axis ◽  
Creep Tests ◽  
Transient Stage ◽  
Stereographic Triangle

AbstractBased on our analysis of a lot of creep rate-strain curves of PST crystals with the different angles between the lamellar plate and the stress axis, designated as ø, it was confirmed that the creep rate and the creep deformation manner strongly depend on the ø. It was supposed that the predominant creep deformation using γ plate during the transient stage is derived by the fully suppression of the operation of another slip systems not parallel to γ plate through α2 plate. It was also confirmed that the initial stress axes of the PST crystals within the standard stereographic triangle move for the [001]-[111] line, and then turn their directions for [111] pole during the transient stage. This moving manner of the stress axis indicated that the first slip system of [101](111) continues to the area near the [001]-[111] line in the standard stereographic triangle, and then, the second slip system of [110](111) operates. By comparing this moving manner to the creep rate-strain curve, it is suggested that the first slip system of [101](111) operates during the Stage I where the light decrease in the creep rate remains, after that, the second slip system of [110](111) appears and leads to steep decrease in the creep rate. This stage was designated as the Stage II. According to this conception, it is supposed that the strain at the end of the Stage I is directly correlated with the angle from the initial stress axis to the [001]-[111] line in the standard stereographic triangle. In this study, this supposition was confirmed by conducting the creep tests at 1148 K/68.6 MPa using two PST crystals with ø of 31° and 34°. The initial stress axis of the PST crystal with ø of 31° locates nearer to the [001]-[-111] line than that of the PST crystal with ø of 34°. The strain at the end of the Stage I of the PST crystal with ø of 31° is half that of the PST crystal with ø of 34°. By analyzing the inverse pole figures of the creep interrupted PST crystals, it was confirmed that the angle from the initial stress axis to the [001]-[111] line is correlated with the strain of the transient stage.

Change in Stress Axis with Creep Deformation in Ni-20mass%Cr Single Crystal with Orientation of [011]

2006 ◽  
Vol 15-17 ◽  
pp. 870-875 ◽  
Author(s):  
Masaomi Mitsutake ◽  
Yoshihiro Terada ◽  
Takashi Matsuo
Keyword(s):  
Creep Rate ◽  
Single Crystal ◽  
Single Crystals ◽  
Slip Plane ◽  
Creep Deformation ◽  
Stage I ◽  
Stage Ii ◽  
Stress Axis ◽  
Transient Stage ◽  
Primary Slip Plane

The features of the creep deformation of γ-single phase single crystals with the composition of Ni-20mass%Cr are characterized by the extended transient stage, which consists of Stage I and Stage II. In the Stage I, the creep rate just after loading remains unchanged, while the creep rate decreases continuously in Stage II. In the single crystals except for the single crystals with the stress axis of [001] and [1, – 11], the predominant creep deformation using the primary slip plane continues. By this deformation, the cross section of specimen turns to elliptical in shape. However, in the single crystals with the angle between stress axis and primary slip plane (111) is more than 45°, the deformation using the primary slip plane does not continue, as a result, the duration of Stage II turn to shorter one. The single crystal with the stress axis of [011] has the largest angle of 55°. In this study, the deformation manner during transient stage of single crystal with the stress axis of [011] orientation is investigated from the two viewpoints. The first one is to clarify the change in deformation manner with decreasing the stress. As a result, with decreasing the stress, the Stage I become clear and strain during Stage I and Stage II become small, furthermore, the decreasing ratio of creep rate with definite strain becomes larger. While, the second viewpoint is to investigate the change in crystallographic orientation of the [011] single crystals with creep deformation using the inverse pole figure obtained by the EBSD method. As a result, at the stress of 29.4 MPa, the spot of stress axis turns from the [011]-[1, – 11] line to the <1, – 01> direction. While, at the stress of 19.6 MPa, the stress axis moves for the [1, – 11] pole along the [011]-[1, – 11] line from the [011] pole. And, it is noteworthy that the spot widely spread from the [011] pole during transient stage. This indicates the large distortion in the primary slip plane and the evidence of heterogeneous deformation.

Tensile Deformation of Si Single Crystals at High Temperatures

2021 ◽  
Vol 1016 ◽  
pp. 1443-1447
Author(s):  
Tubasa Suzuki ◽  
Masaki Tanaka ◽  
Tatsuya Morikawa ◽  
Yelm Okuyama ◽  
Jun Fujise ◽  
...  
Keyword(s):  
Slip System ◽  
Single Crystals ◽  
Tensile Deformation ◽  
Tensile Tests ◽  
Stage Ii ◽  
Electron Backscattered Diffraction ◽  
Kink Bands ◽  
Schmid Factor ◽  
Primary Slip System ◽  
Yield Point Phenomenon

Czochralski silicon single crystals were deformed in tensile tests along the direction at between 1173 K and 1373. Yield point phenomenon were observed in the specimens deformed at below 1273 K while continues yield was observed in the specimens deformed at above 1323 K. It is due to the effect of dislocation starvation in the used crystals. Work-hardening rates in stage II were consistent with those reported in fcc crystals such as copper. The onset of stage II was found to be active before the Schmid factor of the second slip system becomes larger than that of the primary slip system. Electron backscattered diffraction images indicated clear kink bands near grips and in the parallel portion. The kink bands were formed at the middle of stage I, which suggest that the formation of kink bands is a trigger of stage II.

The Creep Deformation and Elevated Temperature Microstructural Stability of a Two-Phase TiAl/Ti3Al Lamellar Alloy.

1994 ◽  
Vol 364 ◽  
Author(s):  
M. F. Bartholomeusz ◽  
J. A. Wert
Keyword(s):  
Elevated Temperature ◽  
Creep Rate ◽  
Microstructural Evolution ◽  
Creep Deformation ◽  
Minimum Creep Rate ◽  
Single Phase ◽  
Lamellar Microstructure ◽  
Microstructural Stability ◽  
Two Phase ◽  
The Individual

AbstractEnhanced work hardening of the phases in the lamellar microstructure has been cited as an explanation for the lower minimum creep rates of a two-phase TiAl/Ti3Al lamellar alloy compared with the minimum creep rates of the individual TiAl and Ti3Al single-phase alloys tested between 980 K and 1130 K. This proposition is confirmed by TEM observations. Thermal and thermomechanical exposure result in the microstructural evolution, which increases the minimum creep rate (εmin) of the lamellar alloy. The effect of microstructural evolution on εmin will be discussed in the present paper.

scholarly journals ɤ-TiAl Alloy: Tensile Creep Deformation Behaviour and Creep Life at 832 °C

2021 ◽  
Author(s):  
Mainak Saha
Keyword(s):  
Steady State ◽  
Creep Deformation ◽  
Original Work ◽  
Single Phase ◽  
Tial Alloy ◽  
Deformation Behaviour ◽  
Steady State Creep ◽  
Tensile Creep ◽  
Creep Life ◽  
Processing Techniques

Creep deformation in single phase ɤ-TiAl alloy manufactured using different processing techniques has been an extensively studied topic since the late 1970s. The present work revisits the original work on understanding the tensile creep deformation behaviour of wrought single-phase ɤ-TiAl alloy by Hayes and Martin [1] and is aimed to develop an understanding of steady state creep. Besides, it is also aimed to investigate the creep life for stress levels of 69.4 and 103.4 MPa at 832 ⁰C using Monkman-Grant [2] approach.

scholarly journals Deformation of Floating Ice Shelves

1957 ◽  
Vol 3 (21) ◽  
pp. 38-42 ◽  
Author(s):  
J. Weertman
Keyword(s):  
Steady State ◽  
Creep Rate ◽  
Creep Deformation ◽  
Plasticity Theory ◽  
Steady State Creep ◽  
Creep Tests ◽  
Ice Shelves ◽  
The Antarctic ◽  
Good Agreement

AbstractThe problem of the creep deformation of floating ice shelves is considered. The problem is solved using Glen’s creep law for ice and Nye’s relation of steady-state creep (the analogue of the Lévy-Miles relation in plasticity theory). Good agreement is obtained between an observed creep rate at Maudheim in the Antarctic and that predicted from the results of creep tests made by Glen.

scholarly journals Observations of pressure effects on the creep of ice single crystals

1996 ◽  
Vol 42 (140) ◽  
pp. 169-175 ◽  
Author(s):  
David M. Cole
Keyword(s):  
Steady State ◽  
Creep Rate ◽  
Single Crystals ◽  
Basal Slip ◽  
Confining Pressure ◽  
Absolute Temperature ◽  
Steady State Creep ◽  
Pressure Effects ◽  
Steady State Creep Rate ◽  
Experimental Errors

AbstractExperiments performed on ice single crystals oriented for basal slip indicate that the steady-state creep rate is only marginally affected by confining pressure up to 19 MPa, at a constant absolute temperature of 263 K. The observations Contradict earlier work at similar pressures and the disparity is examined in terms of experimental errors.

scholarly journals ɤ-TiAl alloy: Tensile creep deformation behaviour and creep life at 832 °C

2021 ◽  
Author(s):  
Mainak Saha
Keyword(s):  
Steady State ◽  
Creep Deformation ◽  
Original Work ◽  
Single Phase ◽  
Tial Alloy ◽  
Deformation Behaviour ◽  
Steady State Creep ◽  
Tensile Creep ◽  
Creep Life ◽  
Processing Techniques

Abstract Creep deformation in single phase ɤ-TiAl alloy manufactured using different processing techniques has been an extensively studied topic since the late 1970s. The present work revisits the original work on understanding the tensile creep deformation behaviour of wrought single-phase ɤ-TiAl alloy by Hayes and Martin [1] and is aimed to develop an understanding of steady state creep. Besides, it is also aimed to investigate the creep life for stress levels of 69.4 and 103.4 MPa at 832 ⁰C using Monkman-Grant [2] approach.

Sign in / Sign up

Export Citation Format

Share Document