Boron Nitride Doped Transparent Polycrystalline Silicon Nitride Ceramics

2010 ◽  
Vol 658 ◽  
pp. 428-431
Author(s):  
Bhupendra Joshi ◽  
Hyun Hwi Lee ◽  
Seung Ho Kim ◽  
Zheng Yi Fu ◽  
Koichi Niihara ◽  
...  
Keyword(s):  
Electron Microscopy ◽  
Mechanical Properties ◽  
Fracture Toughness ◽  
Polycrystalline Silicon ◽  
Sintering Aids ◽  
X Ray Diffraction ◽  
X Ray ◽  
Nitride Ceramics ◽  
Xrd Techniques ◽  
Scanning Electron

The addition of h- BN to a polycrystalline Si3N4 was to increase the fracture toughness and other mechanical properties such as flexural strength and hardness of the material. The hot pressed samples were prepared from the mixture of α-Si3N4, AlN, MgO and h-BN. The composite contained from 0 to 2 wt.% BN powder with sintering aids (9% AlN + 3% MgO). The transparency, mechanical properties and microstructure of hot pressed polycrystalline Si3N4-BN composite materials were investigated by UV/VIS spectrophotometer, scanning electron microscopy (SEM) and X-ray diffraction (XRD) techniques. The transparency decreased with increasing the content of h-BN into Si3N4.

Effect of Sintering Temperature on Microstructure and Mechanical Properties of Al2O3-TiC-ZrO2 Ceramic Composites

2012 ◽  
Vol 476-478 ◽  
pp. 1031-1035
Author(s):  
Wei Min Liu ◽  
Xing Ai ◽  
Jun Zhao ◽  
Yong Hui Zhou
Keyword(s):  
Electron Microscopy ◽  
Mechanical Properties ◽  
Fracture Toughness ◽  
Flexural Strength ◽  
Relative Density ◽  
Sintering Temperature ◽  
Ceramic Composites ◽  
X Ray Diffraction ◽  
X Ray ◽  
Scanning Electron

Al2O3-TiC-ZrO2ceramic composites (ATZ) were fabricated by hot-pressed sintering. The phases and microstructure of the composites were studied by X-ray diffraction (XRD) and scanning electron microscopy (SEM). The relative density and mechanical properties (flexural strength, fracture toughness and Vicker’s hardness) of the composites were tested. The results show that the microstructure of the composites was the gray core-white rim. With the increase of sintering temperature, the relative density and mechanical properties of the composites increased first and then decreased. The composite sintered at 1705°C has the highest synthetical properties, and its relative density, flexural strength, fracture toughness and Vickers hardness are 98.3%,970MPa,6.0 MPa•m1/2and 20.5GPa, respectively.

Mechanical Properties of AlMgB14-xTiB2 Prepared by Field Activated and Pressure Assisted Synthesis

2013 ◽  
Vol 745-746 ◽  
pp. 652-656
Author(s):  
Yang Miao ◽  
Wen Liu ◽  
Lei Zhuang ◽  
Hui Ling Cheng ◽  
Qing Sen Meng
Keyword(s):  
Electron Microscopy ◽  
Mechanical Properties ◽  
Fracture Toughness ◽  
Scanning Electron Microscopy ◽  
Mechanical Alloying ◽  
Composite Ceramic ◽  
X Ray Diffraction ◽  
X Ray ◽  
Wear Tests ◽  
Scanning Electron

In this paper, Mechanical alloying (MA) and field activated and pressure assisted synthesis (FAPAS) were used for preparing the ultra-hard, super-abrasive AlMgB14-xTiB2 composite ceramic. The samples were fabricated at 1500 under a pressure of 60 MPa. The microstructures and compositions of samples were observed and determined by scanning electron microscopy (SEM), energy dispersive X-ray analysis (EDX), X-ray diffraction (XRD). It was indicated that addition of TiB2 was effective for increasing both quantities. A maximum Vichers hardness of 38.5GPa and a fracture toughness of 3.85MPam½ of AlMgB14 reinforced with 70 wt.% of TiB2 were achieved. Abrasion wear tests showed that adding TiB2 would improve the wearability obviously.

scholarly journals Effect of silver nanoparticless in the structure and mechanical properties of mullite/Ag cermets

2019 ◽  
Vol 51 (2) ◽  
pp. 175-187
Author(s):  
Gabriela Téllez-Arias ◽  
José Miranda-Hernández ◽  
Oscar Olea-Mejía ◽  
J. Lemus-Ruiz ◽  
Eduardo Terrés
Keyword(s):  
Electron Microscopy ◽  
Mechanical Properties ◽  
Fracture Toughness ◽  
X Ray Diffraction ◽  
Microstructural Characteristics ◽  
X Ray ◽  
Different Temperatures ◽  
Confocal Scanning ◽  
Confocal Scanning Microscopy ◽  
Scanning Electron

The objective of this work was to study the influence of the addition of silver nanoparticles in the microstructure of mullite at two different temperatures of sintering (1500 and 1600?C), in order to decrease the porosity and increase the density as well better the hardness and fracture toughness. The microstructural characteristics were studied by scanning electron microscopy, confocal scanning microscopy and X-ray diffraction. Mullite/Ag cermets with homogenous microstructure were and a fracture toughness of 2.42 MP??m1/2.

Research on compatibility and surface of high impact bio-based polyamide

2021 ◽  
pp. 095400832110055
Author(s):  
Yang Wang ◽  
Yuhui Zhang ◽  
Yuhan Xu ◽  
Xiucai Liu ◽  
Weihong Guo
Keyword(s):  
Electron Microscopy ◽  
Mechanical Properties ◽  
Scanning Electron Microscopy ◽  
Differential Scanning Calorimetry ◽  
Crystallization Behavior ◽  
High Impact ◽  
X Ray Diffraction ◽  
Scanning Calorimetry ◽  
X Ray ◽  
Scanning Electron

The super-tough bio-based nylon was prepared by melt extrusion. In order to improve the compatibility between bio-based nylon and elastomer, the elastomer POE was grafted with maleic anhydride. Scanning Electron Microscopy (SEM) and Thermogravimetric Analysis (TGA) were used to study the compatibility and micro-distribution between super-tough bio-based nylon and toughened elastomers. The results of mechanical strength experiments show that the 20% content of POE-g-MAH has the best toughening effect. After toughening, the toughness of the super-tough nylon was significantly improved. The notched impact strength was 88 kJ/m2 increasing by 1700%, which was in line with the industrial super-tough nylon. X-ray Diffraction (XRD) and Differential Scanning Calorimetry (DSC) were used to study the crystallization behavior of bio-based PA56, and the effect of bio-based PA56 with high crystallinity on mechanical properties was analyzed from the microstructure.

UTILIZATION OF FLY ASH AND CONCRETE RESIDUE IN THE PRODUCTION OF GEOPOLYMER BRICKS

2017 ◽  
Vol 12 (1) ◽  
pp. 63-77 ◽  
Author(s):  
Siriporn Sirikingkaew ◽  
Nuta Supakata
Keyword(s):  
Electron Microscopy ◽  
Mechanical Properties ◽  
Scanning Electron Microscopy ◽  
Compressive Strength ◽  
Phase Composition ◽  
Fly Ash ◽  
Industrial Waste ◽  
X Ray Diffraction ◽  
X Ray ◽  
Scanning Electron

This study presents the development of geopolymer bricks synthetized from industrial waste, including fly ash mixed with concrete residue containing aluminosilicate compound. The above two ingredients are mixed according to five ratios: 100:0, 95:5, 90:10, 85:15, and 80:20. The mixture's physico-mechanical properties, in terms of water absorption and the compressive strength of the geopolymer bricks, are investigated according to the TIS 168-2546 standard. Scanning electron microscopy (SEM) and X-ray diffraction (XRD) analyses are used to investigate the microstructure and the elemental and phase composition of the brick specimens. The results indicate that the combination of fly ash and concrete residue represents a suitable approach to brick production, as required by the TIS 168–2546 standard.

scholarly journals Amazonian Metakaolin Reactivity for Geopolymer Synthesis

2019 ◽  
Vol 2019 ◽  
pp. 1-7 ◽  
Author(s):  
Ruy A. Sá Ribeiro ◽  
Marilene G. Sá Ribeiro ◽  
Gregory P. Kutyla ◽  
Waltraud M. Kriven
Keyword(s):  
Electron Microscopy ◽  
Mechanical Properties ◽  
Scanning Electron Microscopy ◽  
X Ray Diffraction ◽  
Local Resource ◽  
X Ray ◽  
Potassium Sodium ◽  
Mixing Intensity ◽  
Amazonian Region ◽  
Scanning Electron

To determine the viability of using a local resource for geopolymer synthesis, geopolymers were synthesized using metakaolin made from clay mined in the Amazonian region of Brazil. Samples were made with mixed potassium-sodium and pure sodium metakaolin-based geopolymer. Samples were also made using commercial metakaolin (CMK) from BASF, Inc. as a comparison to the Amazonian metakaolin (AMK). Scanning electron microscopy was used to investigate the microstructure of the materials. X-ray diffraction was able to confirm the formation of geopolymer. The mechanical properties of AMK material were nearly equivalent to those based on CMK. Neither CMK nor AMK reacted completely, although samples made with CMK showed less unreacted material. By increasing the mixing intensity and duration, the amount of residual unreacted material was substantially reduced, and mechanical properties were improved.

SYNERGISTIC REINFORCEMENT OF ORGANOCLAY AND DOUBLE NETWORKING IN NATURAL RUBBER

2013 ◽  
Vol 86 (2) ◽  
pp. 205-217 ◽  
Author(s):  
Hedayatollah Sadeghi Ghari ◽  
Zahra Shakouri
Keyword(s):  
Electron Microscopy ◽  
Mechanical Properties ◽  
Natural Rubber ◽  
Physical And Mechanical Properties ◽  
X Ray Diffraction ◽  
Double Network ◽  
X Ray ◽  
Extension Ratio ◽  
Curing Characteristics ◽  
Scanning Electron

ABSTRACT Research was undertaken on natural rubber (NR) nanocomposites with organoclays. A double-network (DN) structure is formed when a partially cross-linked elastomer is further cross-linked during a state of strain. Two methods were used in the preparation of NR/organoclay nanocomposites: the ordinary method (single-network NR nanocomposite) and double-networked NR (DN-NR) nanocomposites. The single-networked NR nanocomposites were used for comparison. The effects of organoclay (5 phr) with a different extension ratio on curing characteristics, mechanical properties, hardness, swelling behavior, and morphology of single- and double-networked NR nanocomposites were studied. The results showed that double-networked NR nanocomposites exhibited higher physical and mechanical properties. The tensile strength of DN-NR nanocomposites increased up to 33 MPa (more than four times greater than that of pure NR) and then decreased with an increasing extension ratio. Modulus and hardness continuously increased with an increased extension ratio. The microstructure of the NR/organoclay systems was studied by X-ray diffraction and field emission scanning electron microscopy. The effects of different extension ratios on the dispersion of organoclay layers in the nanocomposites were investigated. Generally, results showed that the optimized extension ratio in DN nanocomposites was equal (or about or around) to α= 2.

scholarly journals Investigation of deformation and microstructure of bainite in Cu-9.97%Al-4.62%mn alloy

2014 ◽  
Vol 50 (1) ◽  
pp. 87-90 ◽  
Author(s):  
E. Aldirmaz ◽  
I. Aksoy
Keyword(s):  
Electron Microscopy ◽  
Mechanical Properties ◽  
Scanning Electron Microscopy ◽  
Physical And Mechanical Properties ◽  
Compression Stress ◽  
X Ray Diffraction ◽  
Deformation Effect ◽  
X Ray ◽  
Deformation Test ◽  
Scanning Electron

In this study, some physical and mechanical properties in Cu-9.97%Al-4.62%Mn (wt%) alloy were investigated by X-ray diffraction (XRD), Scanning Electron Microscopy (SEM) and compression deformation test. Bainite phase were obtained in the samples according to SEM and XRD analyses. Compression stress was applied on the alloy in order to investigate the deformation effect on the bainite phase transformation. On the surface of the Cu-9.97%Al-4.62%Mn alloy after the deformation, both bainite and martensite variants formed.

Processing of Biodegradable Polymer Composite Using Soy Protein-Based Resin and Nanoclay

2016 ◽  
Author(s):  
Mohammad K. Hossain ◽  
Samira N. Shaily ◽  
Hadiya J. Harrigan ◽  
Terrie Mickens
Keyword(s):  
Electron Microscopy ◽  
Mechanical Properties ◽  
Scanning Electron Microscopy ◽  
Optical Microscopy ◽  
Soy Protein ◽  
Poly Vinyl Alcohol ◽  
X Ray Diffraction ◽  
Scanning Calorimetry ◽  
X Ray ◽  
Scanning Electron

A completely biodegradable composite was fabricated from an herbal polymer, soy protein concentrate (SPC) resin. Soy protein was modified by adding 30 wt% of glycerol and 5 wt% of poly vinyl alcohol (PVA) to enhance its mechanical as well as thermal property. 3%, 5%, 10%, and 20% nanoclay (NC) were infused into the system. To evaluate its mechanical properties, crystallinity, thermal properties, bonding interaction, and morphological evaluation, tensile, X-ray diffraction (XRD), thermogravimetric analysis (TGA), differential scanning calorimetry (DSC), and Fourier transform infrared spectroscopy (FTIR) tests, and optical microscopy (OM) and scanning electron microscopy (SEM) evaluation were performed. Tensile tests showed that the addition of nanoclay improved the mechanical properties of the modified resin. Soy protein is hydrophilic due to the presence of amino acids that contain various polar groups such as amine, carboxyl, and hydroxyl. As a result, polar nanoclay particles that are exfoliated can be evenly dispersed in the SPC resin. From experimental results, it is clear that adding of nanoclay with SPC resin significantly increased the stiffness of the SPC resin. A combination of 5% clay, 30% glycerol, and 5% PVA with the modified SPC resulted in the maximum stress of 18 MPa and Young modulus of 958 MPa. The modified SPC showed a reduced failure strain as well. X-ray diffraction curves showed an improvement of crystallinity of the prepared resin with increasing amount of nanoclay. Interaction among soy, glycerol, PVA, and nanoclay was clearly demonstrated from the FTIR analysis. Optical microscopy (OM) and scanning electron microscopy (SEM) micrographs revealed rougher surface in the nanoclay infused SPC samples compared to that of the neat one. SEM evaluation revealed rougher fracture surface in the NC infused samples.

Preparation and Mechanical Properties of Rubber/Organoclay Nanocomposites

2011 ◽  
Vol 221 ◽  
pp. 200-204
Author(s):  
Guang Yi Lin ◽  
Ben Fa Gao ◽  
Chuan Sheng Wang
Keyword(s):  
Electron Microscopy ◽  
Mechanical Properties ◽  
Rubber Matrix ◽  
High Tensile Strength ◽  
X Ray Diffraction ◽  
Mechanical Mixing ◽  
X Ray ◽  
Mixing Method ◽  
Mooney Viscosity ◽  
Scanning Electron

The NR/SBR/oranoclay nancomposites were prepared by mechanical mixing method. The dispersion of the oranoclay in the rubber matrix was characterized by X-ray diffraction and scanning electron microscopy. And the effects of different filler and contents on the mechanical properties were investigated. The results showed that the particles of organoclay can be dispersed homogeneously in the rubber matrix. Compbination of carbon black and organoclay shows the synergistic effect which lead to high tensile strength. In addition, organoclay can decrease the Mooney viscosity which is useful for processing. The method is simple, which can be used industrially for use of organoclay in elastomer.

Sign in / Sign up

Export Citation Format

Share Document