Surface Topography and Kerf Study of Nimonic 80A Using Wire-Cut EDM

2014 ◽  
Vol 808 ◽  
pp. 35-41 ◽  
Author(s):  
Amitesh Goswami ◽  
Jatinder Kumar
Keyword(s):  
Surface Topography ◽  
Process Parameters ◽  
Electrical Discharge Machining ◽  
Weight Ratio ◽  
High Strength ◽  
Machining Parameters ◽  
Influence Of Process Parameters ◽  
Nimonic 80A ◽  
Pulse On Time ◽  
Pulse Off Time

Nimonic-80A is a nickel based super alloy which is specifically used in aerospace industry for its high strength to weight ratio and corrosion resistance. This paper presents the influence of process parameters of wire cut Electrical Discharge Machining (WEDM) during the machining of Nimonic 80A with brass wire as electrode and optimization of machining parameters on kerf width. Process parameters (pulse-on time, pulse-off time, peak current, spark gap set voltage, wire feed and wire tension) have been investigated using L27orthogonal array. With the assistance of Taguchi quality design, ANOVA and F-test, significant parameters affecting the kerf have been identified. The surface topography of machined samples has been studied in correlation with the rate of input energy into the spark.

Parameter optimization and experimental study on wire electrical discharge machining of porous Ni40Ti60 alloy

2015 ◽  
Vol 231 (6) ◽  
pp. 956-970 ◽  
Author(s):  
Neeraj Sharma ◽  
Tilak Raj ◽  
Kamal Kumar Jangra
Keyword(s):  
Process Parameters ◽  
Electrical Discharge ◽  
Electrical Discharge Machining ◽  
Machining Process ◽  
Wire Electrical Discharge Machining ◽  
Influence Of Process Parameters ◽  
Work Surface ◽  
Pulse On Time ◽  
Pulse Off Time ◽  
Response Variables

NiTi is a shape memory alloy, mostly employed in cardiovascular stents, orthopedic implants, orthodontic wires, micro-electromechanical systems and so on. The effective and net shape machining of NiTi is very critical for excellent response of this material in medical and other applications. The present experimental work on wire electrical discharge machining process identifies the influence of process parameters that affect the cutting rate, dimensional shift and surface roughness while machining of porous nickel–titanium (Ni40Ti60) alloy. Porous Ni40Ti60 alloy was produced in-house using powder metallurgy technique. Response surface methodology–based central composite rotatable design has been used for the planning of experiments on wire electrical discharge machining. Empirical relations have been developed between the process parameters (pulse on-time, pulse off-time, servo voltage and peak current) and response variables. Desirability approach has been used for optimizing the three response variables simultaneously. Confirmation experiments were also performed at the optimized settings and reflect a close agreement between the predicted and experimental values (percentage error varies from −6.13% to +6.85%). Using wire electrical discharge machining, NiTi alloy can be machined easily and successfully in single-cutting operation, but after the first cut in wire electrical discharge machining, a surface projection appears on work surface which is the unmachined material on work surface.

scholarly journals A Study on Optimization of Process Parameters in Machining of Bronze using Wire-EDM

2021 ◽  
pp. 484-493
Author(s):  
Gajanan Kamble ◽  
Dr. N. Lakshamanaswamy ◽  
Gangadhara H S ◽  
Sharon Markus ◽  
N. Rajath
Keyword(s):  
Surface Roughness ◽  
Process Parameters ◽  
Material Removal Rate ◽  
Material Removal ◽  
Electrical Discharge Machining ◽  
Removal Rate ◽  
Machining Parameters ◽  
Wire Edm ◽  
Pulse On Time ◽  
Pulse Off Time

Wire cut electrical discharge machining (WEDM) is a hybrid manufacturing technology which enables machining of all engineering materials. This research article deals with investigation on Optimization of the Process Parameters of the wire cut EDM of Bronze material of dimension (80*80*40) in mm. Material removal rate, Surface roughness and Kerf width were studied against the process parameters such as Pulse on time(TON), Pulse off time (TOFF) and Current(IP). The machining parameters for wire EDM were optimized for achieving the combined objectives. As there are three input parameters 27 experiments is carried out and full factorial is used. Optimized parameters were found using (ANOVA) and the error percentage can be validated and parameter contribution for the Material removal rate (MRR) and Surface roughness were found.

Optimization of Wire Electrical Discharge Machining Parameters of Activated Carbon Reinforced Aluminium Composite

2020 ◽  
Vol 979 ◽  
pp. 3-9
Author(s):  
G. Ramanan ◽  
M.Madhu Kiran Reddy ◽  
V. Manishankar
Keyword(s):  
Activated Carbon ◽  
Process Parameters ◽  
Electrical Discharge ◽  
Electrical Discharge Machining ◽  
Influential Factors ◽  
Wire Electrical Discharge Machining ◽  
Machining Parameters ◽  
Pulse On Time ◽  
Pulse Off Time ◽  
Wedm Process

The quality of machining through process parameters on the responses in wire electrical discharge machining (WEDM) is studied. This paper discusses the optimization of parameters of a process in WEDM machining with the application of the desirability approach on the basis of response surface methodology (RSM). Pulse on time, servo speed rate, discharge current, and pulse off time have been considered as influential factors. The established experimental data of AA7075 aluminium reinforced with 9% of activated carbon composite to analyze the process parameter effects on responses, like material removal rate (MRR) and surface roughness (SR). After machining multiple regression analysis is used to find the interaction among the process parameters is obtained. The optimal parameters were found using the desirability optimization methodologies as 10.43mm3/min and 3.32μm respectively. The performance of the optimization test confirmed that the proposed method in this study effectively improves the performance of the WEDM process.

Optimization and surface modification in electrical discharge machining of AA 6061/SiCp composite using Cu–W electrode

2015 ◽  
Vol 231 (3) ◽  
pp. 332-348 ◽  
Author(s):  
Balbir Singh ◽  
Jatinder Kumar ◽  
Sudhir Kumar
Keyword(s):  
Process Parameters ◽  
Electrical Discharge Machining ◽  
Removal Rate ◽  
Surface Characteristics ◽  
Electrode Wear ◽  
Material Transfer ◽  
Machined Surface ◽  
Recast Layer Thickness ◽  
Pulse On Time ◽  
Pulse Off Time

This paper presents the experimental investigation on the electro-discharge machining of aluminum alloy 6061 reinforced with SiC particles using sintered Cu–W electrode. Experiments have been designed as per central composite rotatable design, using response surface methodology. Machining characteristics such as material removal rate (MRR), electrode wear ratio (EWR), and surface roughness (SR) have been investigated under the influence of four electrical process parameters; namely peak current, pulse on time, pulse off time, and gap voltage. The process parameters have been optimized to obtain optimal combination of MRR, EWR, and SR. Further, the influence of sintered Cu–W electrode on surface characteristics has been analyzed with scanning electron microscopy, energy dispersive spectroscopy, and Vicker microhardness tests. The results revealed that all the process parameters significantly affect MRR, EWR, and SR. The machined surface properties are modified as a result of material transfer from the electrode. The recast layer thickness is increased at higher setting of electrical parameters. The hardness across the machined surface is also increased by the use of sintered Cu–W electrode.

Mathematical Modeling of Machining Parameters in Electrical Discharge Machining with Cu-B4C Composite Electrode

2012 ◽  
Vol 488-489 ◽  
pp. 871-875
Author(s):  
V. Anandakrishnan ◽  
V. Senthilkumar
Keyword(s):  
Mathematical Models ◽  
Current Pulse ◽  
Electrical Discharge ◽  
Electrical Discharge Machining ◽  
Removal Rate ◽  
Machining Parameters ◽  
Pulse On Time ◽  
Pulse Off Time ◽  
Off Time ◽  
Selection Of

Copper based metal matrix composite reinforced with Boron Carbide is a newly developed Electrical Discharge Machining (EDM) electrode showing better performance than the conventional copper based electrode. Right selection of machining parameters such as current, pulse on time and pulse off time is one of the most important aspects in EDM. In this paper an attempt has been made to develop mathematical models for relating the Material Removal Rate (MRR), Tool Removal Rate (TRR) and Surface roughness (Ra) to machining parameters (current, pulse-on time and pulse-off time). Furthermore, a study was carried out to analyze thSubscript texte effects of machining parameters on various performance parameters such as, MRR, TRR and Ra. The results of Analysis of Variance (ANOVA) indicate that the proposed mathematical models, can adequately describe the performance within the limits of the factors being studied. Response surface modeling is used to develop surface and contour graphs to analyze the effects of EDM input parameters on outer parameters.

scholarly journals Study of wire-electrical discharge machining parameters of titanium alloy by using taguchi method

2018 ◽  
Vol 7 (2.8) ◽  
pp. 10
Author(s):  
A VS Ram Prasad ◽  
Koona Ramji ◽  
B Raghu Kumar
Keyword(s):  
Surface Roughness ◽  
Taguchi Method ◽  
Process Parameters ◽  
Optimization Technique ◽  
Machining Process ◽  
Machining Parameters ◽  
Wire Edm ◽  
Pulse On Time ◽  
Pulse Off Time ◽  
Edm Process

Machining of Titanium alloys is difficult due to their chemical and physical properties namely excellent strength, chemical reactivity and low thermal conductivity. Traditional machining of such materials leads to formation of continuous chips and tool bits are subjected to chatter which leads to formation of poor surface on machined surface. In this study, Wire-EDM one of the most popular unconventional machining process which was used to machine such difficult-to-cut materials. Effect of Wire-EDM process parameters namely peak current, pulse-on- time, pulse-off-time, servo voltage on MRRand SR was investigated by Taguchi method. 0.25 mm brass wire was used in this process as electrode material. A surface roughness tester (Surftest 301) was used to measure surface roughness value of the machined work surface. A multi-response optimization technique was then utilized to optimize Wire-EDM process parameters for achieving maximum MRR and minimum SR simultaneously.

scholarly journals Multi-Objective Optimization of Process Parameters for Powder Mixed Electrical Discharge Machining of Inconel X-750 Alloy Using Taguchi-Topsis Approach

2021 ◽  
Vol 71 (1) ◽  
pp. 1-18
Author(s):  
Basha Shaik Khadar ◽  
Raju M. V. Jagannadha ◽  
Kolli Murahari
Keyword(s):  
Boron Carbide ◽  
Process Parameters ◽  
Electrical Discharge Machining ◽  
Removal Rate ◽  
Optimization Technique ◽  
Dielectric Fluid ◽  
Carbide Powder ◽  
Powder Concentration ◽  
Pulse On Time ◽  
Pulse Off Time

Abstract The paper investigates the influence of boron carbide powder (B4C) mixed in dielectric fluid on EDM of Inconel X-750 alloy. The process parameters selected as discharge current (Ip), pulse on time(Ton), pulse off time(Toff), boron carbide(B4C) powder concentration to examine their performance responses on Material Removal Rate (MRR), Surface Roughness(Ra) and Recast Layer Thickness (RLT).In this study, o examine the process parameters which influence the EDM process during machining of Inconel X-750 alloy using combined techniques of Taguchi and similarity to ideal solutions (TOPSIS).Analysis of variance (ANOVA) was conducted on multi-optimization technique of Taguchi-TOPSIS. ANOVA results identified the best process parameters and their percentages. It developed the mathematical equation on Taguchi-TOPSIS performance characteristics results. The multi optimization results indicated that Ip and Toff are more significant parameters; V, and Ton parameters are less significant. Finally, surface structures were studied at optimized EDM conditions by using scanning electron microscope (SEM).

scholarly journals Multi-Objective Optimization of Wire Electrical Discharge Machining of AL 2124/SIC Composite

2019 ◽  
Vol 9 (1) ◽  
pp. 2155-2163
Keyword(s):  
Electrical Discharge ◽  
Electrical Discharge Machining ◽  
Removal Rate ◽  
High Strength ◽  
Wire Electrical Discharge Machining ◽  
Multi Objective Optimization ◽  
Multi Objective ◽  
Predicted Values ◽  
Pulse On Time ◽  
Pulse Off Time

The growing demand for the use of high strength to weight alloys in industries for manufacturing complex structures challenges the machinability of such advanced materials. In the present investigation, the machinability of SiC particle reinforced Al 2124 composite was studied on Wire electrical discharge machining (WEDM). The process parameters namely pulse on-time (Ton), pulse off time (Toff), peak current (IP), and servo voltage (SV) were optimized by utilizing the central composite design layout. The output responses such as kerf and material removal rate (MRR) were studied in detail. The single and multi-objective optimization was studied for a combination effect using Derringer’s desirability approach and Genetic Algorithm (GA). The experimental and predicted values for each response were validated at the optimized condition. The experimental results were found in line with the predicted values. Multi objective optimization of kerf and MRR by GA showing better result compared to RSM.

scholarly journals Parametric optimization of wire cut electrical discharge machining

2014 ◽  
Vol 3 (2) ◽  
pp. 212
Author(s):  
M. Durairaj ◽  
A.K.S. Ansari ◽  
M. H. Gauthamkumar
Keyword(s):  
Surface Roughness ◽  
Orthogonal Array ◽  
Electrical Discharge ◽  
Electrical Discharge Machining ◽  
Fluid Pressure ◽  
Performance Criteria ◽  
Dielectric Fluid ◽  
Machining Parameters ◽  
Pulse On Time ◽  
Pulse Off Time

Wire Electrical Discharge Machining is a manufacturing process whereby a desired shape is obtained using electrical discharges (or) by repetitive spark cycle. Precision and intricate machining are the strengths. Machining parameters tables provided by the machine tool manufacturers often do not meet the operator requirements. Selection of optimum machining and machining parameters combinations is needed for obtaining higher cutting efficiency and accuracy. In this present study, machining is done using Wire-Cut EDM and optimization of surface roughness is done using Taguchis design of experiments. Experimentation was planned as per Taguchis L16 orthogonal array. Each experiment has been performed under different cutting conditions of gap voltage, pulse ON time, and pulse OFF time and Wire feed. Dielectric fluid pressure, wire speed, wire tension, resistance and cutting length are taken as fixed parameters. Inconel 800 was selected as a work material to conduct the experiments. From experimental results, the surface roughness was determined for each machining performance criteria. Signal to noise ratio was applied to measure the performance characteristics deviating from the actual value. Finally, experimental confirmation was carried out to identify the effectiveness of this proposed method. Keywords: Optimization; Taguchis L-16 Orthogonal Array; Surface Roughness; S/N Ratio.

Optimization of WEDM Process Parameters

2014 ◽  
Vol 592-594 ◽  
pp. 831-835 ◽  
Author(s):  
Vikram Singh ◽  
Sharad Kumar Pradhan
Keyword(s):  
Surface Roughness ◽  
Response Surface ◽  
Process Parameters ◽  
Material Removal Rate ◽  
Material Removal ◽  
Removal Rate ◽  
Machining Parameters ◽  
Pulse On Time ◽  
Pulse Off Time ◽  
Wedm Process

The objective of the present work is to investigate the effects of various WEDM process parameters like pulse on time, pulse off time, corner servo, flushing pressure, wire feed rate, wire tension, spark gap voltage and servo feed on the material removal rate (MRR) & Surface Roughness (SR) and to obtain the optimal settings of machining parameters at which the material removal rate (MRR) is maximum and the Surface Roughness (SR) is minimum in a range. In the present investigation, Inconel 825 specimen is machined by using brass wire as electrode and the response surface methodology (RSM) is for modeling a second-order response surface to estimate the optimum machining condition to produce the best possible response within the experimental constraints.

Sign in / Sign up

Export Citation Format

Share Document