Ag-Enhanced Antibacterial Property of MgO Film

2016 ◽  
Vol 859 ◽  
pp. 90-95 ◽  
Author(s):  
Zafer Alajmi ◽  
Tao Fu ◽  
Yan Tao Zhao ◽  
Shui Yun Yang ◽  
Jia Mao Sun
Keyword(s):  
Silver Nanoparticles ◽  
Photoelectron Spectroscopy ◽  
Antibacterial Property ◽  
Thermal Analyses ◽  
Sol Gel ◽  
Inhibition Zone ◽  
X Ray Diffraction ◽  
X Ray ◽  
Antibacterial Surface ◽  
Modification Of Titanium

MgO and silver-containing MgO (AgMgO, 3.3, 9.1 at% Ag) films were sol-gel coated on titanium to improve its antibacterial property. Thermal analyses of MgAc2·4H2O powder revealed that MgO was crystallized at 400 °C. X-ray diffraction analysis showed that MgO was converted to Mg(OH)2 or Mg5(CO3)4(OH)2·4H2O during the ageing in air. Silver nanoparticles at the surface of AgMgO films were identified by scanning electron microscopy and x-ray photoelectron spectroscopy. The MgO film was about 1.5 um thick. The potentiodynamic polarization test in the Ca-free Hank’s balanced salt solution showed that the coated titanium samples had better corrosion resistance than the polished one. The dissolution of silver nanoparticles resulted in a current peak in the polarization plots. In the antibacterial test against E. Coli, the inhibition zone width was 0.3, 1.6, 2.0 mm for the films with 0, 3.3, 9.1 at% Ag, respectively. The bactericidal mechanisms of the MgO and AgMgO films were discussed. The present work would provide a facile method for antibacterial surface modification of titanium based osteo-implants.

Magnetic Properties of Bulk Zn0.95-XMnXFe0.05O2 Prepared by Sol-Gel Method and Subsequent Hot Pressing

2011 ◽  
Vol 268-270 ◽  
pp. 356-359 ◽  
Author(s):  
Wen Song Lin ◽  
C. H. Wen ◽  
Liang He
Keyword(s):  
Magnetic Properties ◽  
Photoelectron Spectroscopy ◽  
Raw Materials ◽  
Sol Gel ◽  
Secondary Phase ◽  
X Ray Diffraction ◽  
Gel Method ◽  
X Ray ◽  
Sol Gel Method ◽  
Doped Zno

Mn, Fe doped ZnO powders (Zn0.95-xMnxFe0.05O2, x≤0.05) were synthesized by an ameliorated sol-gel method, using Zn(CH3COO)2, Mn(CH3COO)2and FeCl2as the raw materials, with the addition of vitamin C as a kind of chemical reducer. The resulting powder was subsequently compacted under pressure of 10 MPa at the temperature of 873K in vacuum. The crystal structure and magnetic properties of Zn0.95-xMnxFe0.05O2powder and bulk samples have been investigated by X-ray diffraction (XRD) and vibrating sample magnetometer (VSM). X-ray photoelectron spectroscopy (XPS) was used to study chemical valence of manganese, iron and zinc in the samples. The x-ray diffraction (XRD) results showed that Zn0.95-xMnxFe0.05O (x≤0.05) samples were single phase with the ZnO-like wurtzite structure. No secondary phase was found in the XRD spectrum. X-ray photoelectron spectroscopy (XPS) showed that Fe and Mn existed in Zn0.95-xMnxFe0.05O2samples in Fe2+and Mn2+states. The results of VSM experiment proved the room temperature ferromagnetic properties (RTFP) of Mn, Fe co-doped ZnO samples.

FeYO3@rGO nanocomposites: Synthesis, characterization and application in photooxidative degradation of atrazine under visible light

2021 ◽  
Vol 11 (5) ◽  
pp. 706-716
Author(s):  
Nada D. Al-Khthami ◽  
Tariq Altalhi ◽  
Mohammed Alsawat ◽  
Mohamed S. Amin ◽  
Yousef G. Alghamdi ◽  
...  
Keyword(s):  
Visible Light ◽  
Photoelectron Spectroscopy ◽  
Sol Gel ◽  
Bandgap Energy ◽  
X Ray Diffraction ◽  
X Ray ◽  
Transmission Electron ◽  
Reduced Graphene ◽  
Structural Surface ◽  
Adsorption Desorption

Different organic pollutants have been remediated photo catalytically by applying perovskite photocatalysts. Atrazine (ATR) is a pesticide commonly detected as a pollutant in drinking, surface and ground water. Herein, FeYO3@rGO heterojunction was synthesized and applied for photooxidation decomposition of ATR. First, FeYO 3nanoparticles (NPs) were prepared via routine sol-gel. After that, FeYO3 NPs were successfully incorporated with different percentages (5, 10, 15 and 20 wt.%) of reduced graphene oxide (rGO) in the synthesis of novel FeYO3@rGO photocatalyst. Morphological, structural, surface, optoelectrical and optical characteristics of constructed materials were identified via X-ray diffraction (XRD), X-ray photoelectron spectroscopy (XPS), Transmission electron microscopy (TEM), adsorption/desorption isotherms, diffusive reflectance (DR) spectra, and photoluminescence response (PL). Furthermore, photocatalytic achievement of the constructed materials was evaluated via photooxidative degradation of ATR. Various investigations affirmed the usefulness of rGO incorporation on the advancement of formed photocatalysts. Actually, novel nanocomposite containing rGO (15 wt.%) possessed diminished bandgap energy, as well as magnified visible light absorption. Furthermore, such nanocomposite presented exceptional photocatalytic achievement when exposed to visible light as ATR was perfectly photooxidized over finite amount (1.6 g · L-1) from the optimized photocatalyst when illuminated for 30 min. The advanced photocatalytic performance of constructed heterojunctions could be accredited mainly to depressed recombination amid induced charges. The constructed FeYO3@rGO nanocomposite is labelled as efficient photocatalyst for remediation of herbicides from aquatic environments.

Improved Functional Capabilities of Quasi-Two-Dimensional Tungsten Oxide Nanostructures

2016 ◽  
Vol 689 ◽  
pp. 55-59
Author(s):  
Serge Zhuiykov
Keyword(s):  
Photoelectron Spectroscopy ◽  
Sol Gel ◽  
X Ray Diffraction ◽  
Current Sensing ◽  
X Ray ◽  
Force Microscopy ◽  
Functional Capabilities ◽  
Atomic Force ◽  
Oxide Nanostructures ◽  
Afm Analysis

Electrical properties and morphology of orthorhombic β–WO3 nano-flakes with thickness of ~7-9 nm were investigated at the nanoscale using energy dispersive X-ray diffraction (XRD), X-ray photoelectron spectroscopy (XPS) and current sensing force spectroscopy atomic force microscopy (CSFS-AFM, or PeakForce TUNATM). CSFS-AFM analysis established good correlation between the topography of the developed nanostructures and various features of WO3 nano-flakes synthesized via a two-step sol-gel-exfoliation method. It was determined that β–WO3 nano-flakes annealed at 550°C possess distinguished and exceptional thickness-dependent properties in comparison with the bulk, micro- and nano-structured WO3 synthesized at alternative temperatures.

Antibacterial Activity of Nickel -Doped ZnO\MWCNTs hybrid Prepared by Sol-Gel technique

2021 ◽  
Author(s):  
Selma M.H. AL-Jawad ◽  
Zahraa S. Shakir ◽  
Duha S. Ahmed
Keyword(s):  
Antibacterial Activity ◽  
Sol Gel ◽  
Inhibition Zone ◽  
Sem Analysis ◽  
Morphological Properties ◽  
X Ray Diffraction ◽  
Zno Nps ◽  
X Ray ◽  
Vis Spectroscopy ◽  
Doped Zno

ZnO/MWCNTs hybrid and doped with different concentration of Nickel element prepared by using Sol-gel been technique reported. All samples were prepared and characterized by X-Ray Diffraction Analysis (XRD), Energy Dispersive X-ray Spectroscopy (EDS), Fourier-Transform Infrared Spectroscopy (FTIR), Field-Emission Scanning Electron Microscopy (FE-SEM), and UV-Vis spectroscopy have been identified the structural, optical and morphological properties. X-ray diffraction showed the polycrystalline nature with hexagonal wutzite structure of hybrid and doped with Nickel. The crystalline size of the hybrid nanostructure was increasing from 23.73 nm to 34.59 nm. Besides, the UV-Vis spectroscopy showed a significant decrease in the band gap values from 2.97 eV to 2.01 eV. Whereas the FE-SEM analysis confirm the formation spherical shapes of ZnO NPs deposited on cylindrical tubes representing the MWCNTs. The antibacterial activity reveals that the inhibition zone of Ni doped-ZnO/MWCNTs hybrid was 28.5 mm, 26.5 mm toward E. coli and S. aureus bacteria, respectively.

scholarly journals Bulk Versus Surface Modification of Alumina with Mn and Ce Based Oxides for CH4 Catalytic Combustion

Materials ◽  
2019 ◽  
Vol 12 (11) ◽  
pp. 1771 ◽  
Author(s):  
Stefan Neatu ◽  
Mihaela M. Trandafir ◽  
Adelina Stănoiu ◽  
Ovidiu G. Florea ◽  
Cristian E. Simion ◽  
...  
Keyword(s):  
Photoelectron Spectroscopy ◽  
Catalytic Combustion ◽  
Mixed Oxides ◽  
Sol Gel ◽  
Nitrogen Adsorption ◽  
X Ray Diffraction ◽  
X Ray ◽  
Temperature Programmed ◽  
Catalytic Combustion Of Methane ◽  
Adsorption Desorption

This study presents the synthesis and characterization of lanthanum-modified alumina supported cerium–manganese mixed oxides, which were prepared by three different methods (coprecipitation, impregnation and citrate-based sol-gel method) followed by calcination at 500 °C. The physicochemical properties of the synthesized materials were investigated by various characterization techniques, namely: nitrogen adsorption-desorption isotherms, X-ray diffraction (XRD), X-ray photoelectron spectroscopy (XPS), scanning electron microscopy (SEM) and H2–temperature programmed reduction (TPR). This experimental study demonstrated that the role of the catalytic surface is much more important than the bulk one. Indeed, the incipient impregnation of CeO2–MnOx catalyst, supported on an optimized amount of 4 wt.% La2O3–Al2O3, provided the best results of the catalytic combustion of methane on our catalytic micro-convertors. This is mainly due to: (i) the highest pore size dimensions according to the Brunauer-Emmett-Teller (BET) investigations, (ii) the highest amount of Mn4+ or/and Ce4+ on the surface as revealed by XPS, (iii) the presence of a mixed phase (Ce2MnO6) as shown by X-ray diffraction; and (iv) a higher reducibility of Mn4+ or/and Ce4+ species as displayed by H2–TPR and therefore more reactive oxygen species.

scholarly journals Photocatalytic Performance of SiO2/CNOs/TiO2 to Accelerate the Degradation of Rhodamine B under Visible Light

Nanomaterials ◽  
2019 ◽  
Vol 9 (12) ◽  
pp. 1671 ◽  
Author(s):  
Weike Zhang ◽  
Yanrong Zhang ◽  
Kai Yang ◽  
Yanqing Yang ◽  
Jia Jia ◽  
...  
Keyword(s):  
Photocatalytic Activity ◽  
Visible Light ◽  
Rhodamine B ◽  
Photoelectron Spectroscopy ◽  
Degradation Rate ◽  
Photocatalytic Performance ◽  
Sol Gel ◽  
X Ray Diffraction ◽  
X Ray ◽  
Electronic Microscope

A silicon dioxide/carbon nano onions/titanium dioxide (SiO2/CNOs/TiO2) composite was synthesized by a simple sol-gel method and characterized by the methods of X-ray diffraction (XRD), scanning electronic microscope (SEM), X-ray photoelectron spectroscopy (XPS), Brunauer–Emmett–Teller (BET), Fourier transform infrared (FTIR), thermogravimetric analysis (TG), differential scanning calorimeter (DSC) and UV-Vis diffuse reflectance spectra (UV-Vis DRS). In this work, the photocatalytic activity of the SiO2/CNOs/TiO2 photocatalyst was assessed by testing the degradation rate of Rhodamine B (RhB) under visible light. The results indicated that the samples exhibited the best photocatalytic activity when the composite consisted of 3% CNOs and the optimum dosage of SiO2/CNOs/TiO2(3%) was 1.5 g/L as evidenced by the highest RhB degradation rate (96%). The SiO2/CNOs/TiO2 composite greatly improved the quantum efficiency of TiO2. This work provides a new option for the modification of subsequent nanocomposite oxide nanoparticles.

scholarly journals Ultrasound enhanced heterogeneous activation of peroxymonosulfate by a Co-NiOx catalyst

2017 ◽  
Vol 76 (6) ◽  
pp. 1436-1446 ◽  
Author(s):  
Chenmo Wei ◽  
Jing Zhang ◽  
Yongli Zhang ◽  
Gucheng Zhang ◽  
Peng Zhou ◽  
...  
Keyword(s):  
Photoelectron Spectroscopy ◽  
Sol Gel ◽  
Maximum Efficiency ◽  
Acid Orange 7 ◽  
X Ray Diffraction ◽  
X Ray ◽  
Surface Hydroxyl ◽  
Transmission Electron ◽  
Initial Ph ◽  
Reactive Oxidant

Sulfate radical-based advanced oxidation processes have had considerable attention due to the highly oxidizing function of sulfate radicals (SO4−·) resulting in acceleration of organic pollutants degradation in aqueous environments. A Co-Ni mixed oxide nanocatalyst, which was prepared by the sol-gel method, was employed to activate peroxymonosulfate (PMS, HSO5−) to produce SO4−· with Acid Orange 7 (AO7) selected as a radical probe. The catalyst was characterized by X-ray diffraction (XRD), X-ray photoelectron spectroscopy (XPS), Fourier transform infrared spectroscopy (FT-IR) and transmission electron microscopy (TEM). The characterization results indicated that the ingredient of the catalyst had been changed and the amount of surface hydroxyl increased significantly with the addition of Ni. Therefore, it proved that Co-NiOx catalyst was more effective than CoOx to activate PMS. Moreover, ultrasound (US) can increase the degradation rate of AO7 and US/Co-NiOx/PMS system. This study also focused on some synthesis parameters and the system reached the maximum efficiency under the condition when [PMS] = 0.4 mM, [catalyst] = 0.28 g/L, Pus = 200 W. The AO7 removal in these systems follows first order kinetics. Last but not least, quenching studies was conducted which indicated that the amount of hydroxyl radicals (·OH) increases with the increase of initial pH and SO4−· was the primary reactive oxidant for AO7 degradation.

Preparation of PCL/PVP/Ag Nanofiber Membranes by Electrospinning Method

2012 ◽  
Vol 268-270 ◽  
pp. 580-583 ◽  
Author(s):  
Yong Tang Jia ◽  
Cui Wu ◽  
Feng Chun Dong ◽  
Gang Huang ◽  
Xian Hua Zeng
Keyword(s):  
Silver Nanoparticles ◽  
Photoelectron Spectroscopy ◽  
Composite Nanofibers ◽  
Average Diameter ◽  
Vinyl Pyrrolidone ◽  
X Ray Diffraction ◽  
X Ray ◽  
Electrospinning Method ◽  
Nanofiber Membranes ◽  
Poly Vinyl Pyrrolidone

The composite nanofiber membranes of poly (ε-caprolactone)/poly(vinyl pyrrolidone) (PCL/PVP) containing silver nanoparticles were prepared by electrospinning method. The morphology of composite nanofibers was characterized by scanning electron microscopy (SEM). The silver nanoparticles on the electrospun fibers were characterized by X-Ray diffraction (XRD) and X-ray photoelectron spectroscopy (XPS). The contact angle and water uptake of PCL/PVP/Ag nanofiber membranes were measured. The SEM photos indicated that the average diameter of the fibers was significantly decreased with the addition of silver nanoparticles. The X-Ray images showed that Ag nanoparticles were distributed on the surface of nanofiber membranes. When the PVP mole ratio was higher than 15%, the nanofiber membranes showed good hydrophilic property. The PCL/PVP/Ag nanofiber membranes could be applied to prepare wound dressing.

Photoconversion of CO2 using copper-modified titanium dioxide nanoparticles

2011 ◽  
Vol 76 (11) ◽  
pp. 1335-1346 ◽  
Author(s):  
Jing Wei ◽  
Xin Tan ◽  
Tao Yu ◽  
Lin Zhao
Keyword(s):  
Titanium Dioxide ◽  
Photoelectron Spectroscopy ◽  
Titanium Dioxide Nanoparticles ◽  
Sol Gel ◽  
Chemical Properties ◽  
High Photocatalytic Activity ◽  
X Ray Diffraction ◽  
X Ray ◽  
Uv Illumination ◽  
One Step

A series of copper-modified titanium dioxide (Cu/TiO2) nanoparticles were synthesized via one-step sol-gel method. The crystal structure and chemical properties were characterized using X-ray diffraction (XRD) and X-ray photoelectron spectroscopy (XPS). The Cu/TiO2nanoparticles were applied to CO2photoconversion and the yield of formaldehyde was used to evaluate the photocatalytic performance. The optimum amount of copper modifying was 0.6 wt.% and the yield of formaldehyde was 946 μmol/gcatunder UV illumination for 6 h. 20 wt.% Cu/TiO2also performed a high photocatalytic activity, which yielded 433 μmol/gcatformaldehyde under UV illumination for 6 h.

Synthesis, Characterization and Photocatalytic Activity of Nb-Doped TiO2 Nanoparticles

2012 ◽  
Vol 455-456 ◽  
pp. 110-114 ◽  
Author(s):  
Xuan Dong Li ◽  
Xi Jiang Han ◽  
Wen Ying Wang ◽  
Xiao Hong Liu ◽  
Yan Wang ◽  
...  
Keyword(s):  
Aqueous Solution ◽  
Photocatalytic Activity ◽  
Methyl Orange ◽  
Photoelectron Spectroscopy ◽  
Sol Gel ◽  
Molar Ratio ◽  
X Ray Diffraction ◽  
Doped Tio2 ◽  
X Ray ◽  
Vis Spectroscopy

Nb-doped TiO2 powders with different concentrations of Nb have been synthesized by a sol-gel method and characterized by a series of technologies including X-ray diffraction (XRD), X-ray photoelectron spectroscopy (XPS) and UV-vis spectroscopy. The photocatalytic activity of Nb-doped TiO2 is evaluated by degradation efficiency of methyl orange in aqueous solution. The results indicate that the photocatalytic activity of Nb-doped TiO2 synthesized with a Nb/Ti molar ratio of 5% is higher than that of TiO2 under the visible light.

Sign in / Sign up

Export Citation Format

Share Document