Wettability Alteration of Dolomite Rock Using Nanofluids for Enhanced Oil Recovery

2016 ◽  
Vol 864 ◽  
pp. 194-198 ◽  
Author(s):  
Mohd Shahrizan Moslan ◽  
Wan Rosli Wan Sulaiman ◽  
Abdul Razak Ismail ◽  
Mohd Zaidi Jaafar ◽  
Issham Ismail
Keyword(s):  
Contact Angle ◽  
Interfacial Tension ◽  
Enhanced Oil Recovery ◽  
Oil Recovery ◽  
Ion Pairs ◽  
Adsorption Rate ◽  
Wettability Alteration ◽  
Rock Surface ◽  
Wet Condition ◽  
The Impact

Wettability alteration of rock by surfactant has been considered as feasible method for recovery of oil reservoirs by modifying the wettability of rock surface from oil-wet to water-wet condition. The impact of surfactant can be enhanced by adding nanoparticles. Cationic surfactant performed well in carbonate rock by forming ion pairs between cationic head and acidic component of the crude. Meanwhile, nanoparticles will form continuous wedge film between the liquid and solid surface. In this paper, Al2O3 and ZrO2 nanoparticles were used as enhanced oil recovery (EOR) agents. The impact of these two nanoparticles on contact angle and interfacial tension was studied. Besides that, adsorption Cetyltrimethylammonium Bromide (CTAB) surfactant on rock surface was also investigated. The results show a significant change in water-oil contact angle after application of surfactant and nanoparticles. Initial water-oil contact angle for 6 dolomites demonstrate oil-wet condition. Then, the dolomites were submerged in prepared solution for 48 hours. The result shows that, dolomites 2, 5 and 6 changes drastically to more water-wet condition with contact angle 56°, 40° and 47° respectively. For surfactant adsorption, the adsorption is very fast at the beginning. The adsorption rate after 5 minutes was 50 mg/g and after 60 minutes the adsorption rate was 310 mg/g. The adsorption rate slowed down after 60 minutes and after 180 minutes the adsorption rate was 315 mg/g in which the rate of adsorption achieve equilibrium. Nanoparticles retention test and Zeta potential shows that Al2O3 is more stable than ZrO2. The results for interfacial tension (IFT) also show a significant reduction. The IFT value reduces from 8.46 mN/m to 1.65 mN/m and 1.85 mN/m after the application of Al2O3 and ZrO2 nanofluids respectively

scholarly journals Recent Advances in Nanoparticles Enhanced Oil Recovery: Rheology, Interfacial Tension, Oil Recovery, and Wettability Alteration

2017 ◽  
Vol 2017 ◽  
pp. 1-15 ◽  
Author(s):  
Muhammad Shahzad Kamal ◽  
Ahmad A. Adewunmi ◽  
Abdullah S. Sultan ◽  
Mohammed F. Al-Hamad ◽  
Umer Mehmood
Keyword(s):  
Interfacial Tension ◽  
Enhanced Oil Recovery ◽  
Oil Recovery ◽  
Mobility Ratio ◽  
Wettability Alteration ◽  
Factors Affecting ◽  
Recent Advances ◽  
The Impact ◽  
Recovery Methods

Chemically enhanced oil recovery methods are utilized to increase the oil recovery by improving the mobility ratio, altering the wettability, and/or lowering the interfacial tension between water and oil. Surfactants and polymers have been used for this purpose for the last few decades. Recently, nanoparticles have attracted the attention due to their unique properties. A large number of nanoparticles have been investigated for enhanced oil recovery applications either alone or in combination with surfactants and/or polymers. This review discusses the various types of nanoparticles that have been utilized in enhanced oil recovery. The review highlights the impact of nanoparticles on wettability alteration, interfacial tension, and rheology. The review also covers the factors affecting the oil recovery using nanoparticles and current challenges in field implementation.

scholarly journals Application of ion-engineered Persian Gulf seawater in EOR: effects of different ions on interfacial tension, contact angle, zeta potential, and oil recovery

2021 ◽  
Author(s):  
Amir Hossein Saeedi Dehaghani ◽  
Seyed Masoud Ghalamizade Elyaderani
Keyword(s):  
Contact Angle ◽  
Zeta Potential ◽  
Interfacial Tension ◽  
Oil Recovery ◽  
Persian Gulf ◽  
Rock Surface ◽  
Divalent Ions ◽  
Smart Water ◽  
Wet Condition ◽  
The Persian Gulf

AbstractIn this study, we initially performed interfacial tension (IFT) tests to investigate the potential of using the Persian Gulf seawater (PGSW) as smart water with different concentrations of NaCl, KCl, MgCl2, CaCl2, and Na2SO4. Next, for each salt, at the concentration where IFT was minimum, we conducted contact angle, zeta potential, and micromodel flooding tests. The results showed that IFT is minimized if NaCl or KCl is removed from PGSW; thus, for solutions lacking NaCl and KCl, the IFT values were obtained at 26.29 and 26.56 mN/m, respectively. Conversely, in the case of divalent ions, minimum IFT occurred when the concentration of MgCl2, CaCl2, and Na2SO4 in PGSW increased. Specifically, a threefold rise in the concentration of Na2SO4 further reduced IFT as compared to optimal concentrations of MgCl2 or CaCl2. It should be mentioned that eliminating NaCl from PGSW resulted in the lowest IFT value compared to adding or removing other ions. Whereas the removal of NaCl caused the contact angle to decrease from 91.0° to 67.8° relative to PGSW and changed surface wettability to weakly water-wet, eliminating KCl did not considerably change the contact angle, such that it only led to a nine-degree reduction in this angle relative to PGSW and left wettability in the same neutral-wet condition. At optimal concentrations of MgCl2, CaCl2, and Na2SO4, only an increase in Na2SO4 concentration in PGSW could change wettability from neutral-wet to weakly water-wet. For solutions with optimal concentrations, the removal of NaCl or KCl caused the rock surface to have slightly higher negative charges, and increasing the concentration of divalent ions led to a small reduction in the negative charge of the surface. The results of micromodel flooding indicated that NaCl-free PGSW could raise oil recovery by 10.12% relative to PGSW. Furthermore, when the Na2SO4 concentration in PGSW was tripled, the oil recovery increased by 7.34% compared to PGSW. Accordingly, depending on the conditions, it is possible to use PGSW so as to enhance the efficiency of oil recovery by removing NaCl or by increasing the concentration of Na2SO4 three times.

scholarly journals Wettability alteration and oil recovery by spontaneous imbibition of smart water and surfactants into carbonates

2020 ◽  
Vol 17 (3) ◽  
pp. 712-721 ◽  
Author(s):  
Saeb Ahmadi ◽  
Mostafa Hosseini ◽  
Ebrahim Tangestani ◽  
Seyyed Ebrahim Mousavi ◽  
Mohammad Niazi
Keyword(s):  
Contact Angle ◽  
Enhanced Oil Recovery ◽  
Oil Recovery ◽  
Carbonate Rock ◽  
Spontaneous Imbibition ◽  
Wettability Alteration ◽  
Rock Surface ◽  
Smart Water ◽  
Fractured Carbonate ◽  
Enhance Oil Recovery

AbstractNaturally fractured carbonate reservoirs have very low oil recovery efficiency owing to their wettability and tightness of matrix. However, smart water can enhance oil recovery by changing the wettability of the carbonate rock surface from oil-wet to water-wet, and the addition of surfactants can also change surface wettability. In the present study, the effects of a solution of modified seawater with some surfactants, namely C12TAB, SDS, and TritonX-100 (TX-100), on the wettability of carbonate rock were investigated through contact angle measurements. Oil recovery was studied using spontaneous imbibition tests at 25, 70, and 90 °C, followed by thermal gravity analysis to measure the amount of adsorbed material on the carbonate surface. The results indicated that Ca2+, Mg2+, and SO42− ions may alter the carbonate rock wettability from oil-wet to water-wet, with further water wettability obtained at higher concentrations of the ions in modified seawater. Removal of NaCl from the imbibing fluid resulted in a reduced contact angle and significantly enhanced oil recovery. Low oil recoveries were obtained with modified seawater at 25 and 70 °C, but once the temperature was increased to 90 °C, the oil recovery in the spontaneous imbibition experiment increased dramatically. Application of smart water with C12TAB surfactant at 0.1 wt% changed the contact angle from 161° to 52° and enhanced oil recovery to 72%, while the presence of the anionic surfactant SDS at 0.1 wt% in the smart water increased oil recovery to 64.5%. The TGA analysis results indicated that the adsorbed materials on the carbonate surface were minimal for the solution containing seawater with C12TAB at 0.1 wt% (SW + CTAB (0.1 wt%)). Based on the experimental results, a mechanism was proposed for wettability alteration of carbonate rocks using smart water with SDS and C12TAB surfactants.

scholarly journals Mechanism of active silica nanofluids based on interface-regulated effect during spontaneous imbibition

2021 ◽  
Author(s):  
Xu-Guang Song ◽  
Ming-Wei Zhao ◽  
Cai-Li Dai ◽  
Xin-Ke Wang ◽  
Wen-Jiao Lv
Keyword(s):  
Contact Angle ◽  
Interfacial Tension ◽  
Oil Recovery ◽  
Dynamic Contact Angle ◽  
Liquid Interface ◽  
Spontaneous Imbibition ◽  
Wettability Alteration ◽  
Low Permeability ◽  
Oil Water ◽  
Solid Liquid

AbstractThe ultra-low permeability reservoir is regarded as an important energy source for oil and gas resource development and is attracting more and more attention. In this work, the active silica nanofluids were prepared by modified active silica nanoparticles and surfactant BSSB-12. The dispersion stability tests showed that the hydraulic radius of nanofluids was 58.59 nm and the zeta potential was − 48.39 mV. The active nanofluids can simultaneously regulate liquid–liquid interface and solid–liquid interface. The nanofluids can reduce the oil/water interfacial tension (IFT) from 23.5 to 6.7 mN/m, and the oil/water/solid contact angle was altered from 42° to 145°. The spontaneous imbibition tests showed that the oil recovery of 0.1 wt% active nanofluids was 20.5% and 8.5% higher than that of 3 wt% NaCl solution and 0.1 wt% BSSB-12 solution. Finally, the effects of nanofluids on dynamic contact angle, dynamic interfacial tension and moduli were studied from the adsorption behavior of nanofluids at solid–liquid and liquid–liquid interface. The oil detaching and transporting are completed by synergistic effect of wettability alteration and interfacial tension reduction. The findings of this study can help in better understanding of active nanofluids for EOR in ultra-low permeability reservoirs.

scholarly journals Carbon dioxide adsorption and interaction with formation fluids of Jordanian unconventional reservoirs

2021 ◽  
Author(s):  
H. Samara ◽  
T. V. Ostrowski ◽  
F. Ayad Abdulkareem ◽  
E. Padmanabhan ◽  
P. Jaeger
Keyword(s):  
Carbon Dioxide ◽  
Contact Angle ◽  
Interfacial Tension ◽  
Oil Recovery ◽  
Gas Adsorption ◽  
Sessile Drop ◽  
Global Climate ◽  
Gravimetric Method ◽  
Rock Surface ◽  
Operating Pressure

AbstractShales are mostly unexploited energy resources. However, the extraction and production of their hydrocarbons require innovative methods. Applications involving carbon dioxide in shales could combine its potential use in oil recovery with its storage in view of its impact on global climate. The success of these approaches highly depends on various mechanisms taking place in the rock pores simultaneously. In this work, properties governing these mechanisms are presented at technically relevant conditions. The pendant and sessile drop methods are utilized to measure interfacial tension and wettability, respectively. The gravimetric method is used to quantify CO2 adsorption capacity of shale and gas adsorption kinetics is evaluated to determine diffusion coefficients. It is found that interfacial properties are strongly affected by the operating pressure. The oil-CO2 interfacial tension shows a decrease from approx. 21 mN/m at 0.1 MPa to around 3 mN/m at 20 MPa. A similar trend is observed in brine-CO2 systems. The diffusion coefficient is observed to slightly increase with pressure at supercritical conditions. Finally, the contact angle is found to be directly related to the gas adsorption at the rock surface: Up to 3.8 wt% of CO2 is adsorbed on the shale surface at 20 MPa and 60 °C where a maximum in contact angle is also found. To the best of the author’s knowledge, the affinity of calcite-rich surfaces toward CO2 adsorption is linked experimentally to the wetting behavior for the first time. The results are discussed in terms of CO2 storage scenarios occurring optimally at 20 MPa.

scholarly journals A mechanistic investigation of low salinity water flooding coupled with ion tuning for enhanced oil recovery

RSC Advances ◽  
2020 ◽  
Vol 10 (69) ◽  
pp. 42570-42583
Author(s):  
Rohit Kumar Saw ◽  
Ajay Mandal
Keyword(s):  
Enhanced Oil Recovery ◽  
Oil Recovery ◽  
Water Flooding ◽  
Wettability Alteration ◽  
Rock Surface ◽  
Calcite Dissolution ◽  
Low Salinity ◽  
Low Salinity Water ◽  
Mechanistic Investigation ◽  
Salinity Water

The combined effects of dilution and ion tuning of seawater for enhanced oil recovery from carbonate reservoirs. Dominating mechanisms are calcite dissolution and the interplay of potential determining ions that lead to wettability alteration of rock surface.

scholarly journals Experimental and modeling study of wettability alteration through seawater injection in limestone: a case study

2020 ◽  
Vol 17 (3) ◽  
pp. 749-758
Author(s):  
Omolbanin Seiedi ◽  
Mohammad Zahedzadeh ◽  
Emad Roayaei ◽  
Morteza Aminnaji ◽  
Hossein Fazeli
Keyword(s):  
Oil Recovery ◽  
Contact Angle Measurement ◽  
Angle Measurement ◽  
Carbonate Reservoirs ◽  
Water Flooding ◽  
Wettability Alteration ◽  
Rock Surface ◽  
Indirect Contact ◽  
Molecular Kinetic Theory ◽  
Wet Condition

AbstractWater flooding is widely applied for pressure maintenance or increasing the oil recovery of reservoirs. The heterogeneity and wettability of formation rocks strongly affect the oil recovery efficiency in carbonate reservoirs. During seawater injection in carbonate formations, the interactions between potential seawater ions and the carbonate rock at a high temperature can alter the wettability to a more water-wet condition. This paper studies the wettability of one of the Iranian carbonate reservoirs which has been under Persian Gulf seawater injection for more than 10 years. The wettability of the rock is determined by indirect contact angle measurement using Rise in Core technique. Further, the characterization of the rock surface is evaluated by molecular kinetic theory (MKT) modeling. The data obtained from experiments show that rocks are undergoing neutral wetting after the aging process. While the wettability of low permeable samples changes to be slightly water-wet, the wettability of the samples with higher permeability remains unchanged after soaking in seawater. Experimental data and MKT analysis indicate that wettability alteration of these carbonate rocks through prolonged seawater injection might be insignificant.

scholarly journals Synthesis and Characterization of Polymeric Surfactant from Palm Oil Methyl Ester and Vinyl Acetate for Chemical Flooding

REAKTOR ◽  
2021 ◽  
Vol 21 (2) ◽  
pp. 65-73
Author(s):  
Agam Duma Kalista Wibowo ◽  
Pina Tiani ◽  
Lisa Aditya ◽  
Aniek Sri Handayani ◽  
Marcelinus Christwardana
Keyword(s):  
Methyl Ester ◽  
Interfacial Tension ◽  
Vinyl Acetate ◽  
Enhanced Oil Recovery ◽  
Oil Recovery ◽  
Mobility Control ◽  
Wettability Alteration ◽  
Polymeric Surfactant ◽  
Chemical Flooding

Surfactants for enhanced oil recovery are generally made from non-renewable petroleum sulfonates and their prices are relatively expensive, so it is necessary to synthesis the bio-based surfactants that are renewable and ecofriendly. The surfactant solution can reduce the interfacial tension (IFT) between oil and water while vinyl acetate monomer has an ability to increase the viscosity as a mobility control. Therefore, polymeric surfactant has both combination properties in reducing the oil/water IFT and increasing the viscosity of the aqueous solution simultaneously. Based on the study, the Critical Micelle Concentration (CMC) of Polymeric Surfactant was at 0.5% concentration with an IFT of 7.72x10-2 mN/m. The best mole ratio of methyl ester sulfonate to vinyl acetate for polymeric surfactant synthesis was 1:0.5 with an IFT of 6.7x10-3 mN/m. Characterization of the product using FTIR and HNMR has proven the creation of polymeric surfactant. Based on the wettability alteration study, it confirmed that the product has an ability to alter from the initial oil-wet to water-wet quartz surface. In conclusion, the polymeric surfactant has ultralow IFT and could be an alternative surfactant for chemical flooding because the IFT value met with the required standard for chemical flooding ranges from 10-2 to 10-3 mN/m.Keywords: Enhanced Oil recovery, Interfacial Tension, Methyl Ester Sulfonate, Polymeric surfactant, vinyl acetate

Sign in / Sign up

Export Citation Format

Share Document